TE Connectivity (Deutsch)

Deutsch DTP connectors

DTP seriesDeutsch DTP connectorDTP04 / DTP06

A Deutsch DTP connector is the power member of TE's DT family: a sealed, rectangular wire-to-wire housing with size 12 contacts rated at 25 A each. TE sells 2 way and 4 way DTP receptacles and plugs, rated -55 to 125 °C, IP68 and IP6K9K, with separate orange wedge locks.710122

At a glance

Contact size
  • Size 12
  • Mating pin diameter 2.4 mm0.094 in
Sourced710
Current25 A maximum per contactSourced7103
Layouts2and 4 waySourced79810
Wire range
  • 12-14 AWG on the standard solid contacts2-3.3 mm²
  • 10-14 AWG quoted for the series
TE's standard size 12 contacts list 12-14 AWG. The Mouser launch note quotes 10-14 AWG for the series without naming a 10 AWG contact.Conflict342
Insulation OD
  • 3.4-4.3 mm receptacles0.134-0.169 in
  • 3.4-4.9 mm plugs0.134-0.193 in
Sourced710
Temperature-55 to 125°C-67 to 257 °FSourced710
SealingIP68 and IP6K9KSourced710
Operating voltage200V AC/DCSourced710
Pitch
  • 6.7 mm0.264 in
  • 10.2 mm row to row on 4 way0.4 in
Sourced7108
Wedge lockSeparate orange PBT wedge: WP-2P, WP-2S, WP-4P, WP-4SSourced12131415

What a Deutsch DTP connector is

The Deutsch DTP connector is the higher-current sister of the DT series.

It uses size 12 contacts rated 25 A, against 13 A for DT size 16 contacts, in 2 way and 4 way housings.762

Naming follows DT

DTP04 receptacles hold pins and DTP06 plugs hold sockets. TE lists the circuit application as power, which suits feeds to fans, pumps and power distribution boxes.Medium79810

DTP housings and their wedges

All four housings carry size 12 contacts rated 25 A, work from -55 to 125 °C and seal to IP68 and IP6K9K.

DTP receptacles and plugs (TE product pages)7981012131415
PartHalfWays / rowsL x W x H (mm)Wedge lock
DTP04-2PReceptacle (pins)2 / 122.1 x 22.1 x 47.3WP-2P (orange)
DTP06-2SPlug (sockets)2 / 118.6 x 18.6 x 34.6WP-2S (orange)
DTP04-4PReceptacle (pins)4 / 226.6 x 26.9 x 47.3WP-4P (orange)
DTP06-4SPlug (sockets)4 / 224.4 x 22.0 x 34.6WP-4S (orange)

TE's product pages give the long axis as height for DTP housings. DTP04-4P is listed in PA66 GF15; the others in glass-filled polyamide.

Sizes are TE product-page values.79810

DTP contacts and tools

DTP housings take size 12 Deutsch common contacts.

Crimp tool

HDT-48-00: four-indent hand tool for solid size 12, 16 and 20 contacts

Sourced11
Contact removal tool
  • DT-RT1, front release
  • TE lists DT, DTP and DTM
Sourced5
Sealing plug114017, white, for size 12 and 16 cavitiesSourced · medium1
Size 12 contacts for DTP housings (TE product pages)34
PartRoleStyleWirePlating
0460-204-12141PinSolid12-14 AWG (2.08-3.31 mm²)Nickel
0462-203-12141SocketSolid12-14 AWG (2-3 mm²)Nickel

The standard solid nickel pair covers 12-14 AWG and carries 25 A typical.34

DTP vs DT

Choose DTP when a circuit needs more than the 13 A a DT size 16 contact carries.

DTP and DT compared (TE product pages)71062
ItemDTPDT
Contact size1216
Current per contact25 A13 A
Operating voltage200 V AC/DC250 V AC/DC
Layouts2, 4 way2-12 way
Insulation OD3.4-4.9 mm2.23-3.68 mm

The housings are larger, the operating voltage is 200 V rather than 250 V, and DTP contacts, wedges and housings do not interchange with DT.Medium762

Assembly notes

Fit the wedge only after every cavity holds a contact or a sealing plug.

TE sells the WP wedges separately as secondary locks.12131415

The contact range (12-14 AWG) sets what fits, not what the circuit needs. Size the wire for the load current and run length, and check voltage drop with the wire gauge calculator.Medium3

CAD and drawings

We link to the maker's own downloads and do not rehost drawings, 3D models or specifications: the makers' terms grant no redistribution. Our cavity maps are drawn from the cavity numbers, never traced from these drawings.

Crimp and assembly quick card

Strip length

Solid size 12 (0460-204-12141, 0462-203-12141): 5.64-7.21 mm (0.222-0.284 in).

Sourced1920
Crimp height

Solid 0460-204-12/0462-203-12 on HDT-48-00 at 12 AWG (reference only, validate by pull test): 1.38-1.51 mm lock indent, 1.55-1.71 mm entry indent.

For 14 AWG, the HDT-48-00 table lists gold contacts 0460-220-12/0462-210-12 (1.29-1.40 / 1.34-1.62 mm), not the nickel 0460-204-12141 / 0462-203-12141 already in the library.Sourced19
Pull-out force (minimum)
  • Crimp tensile minimum, solid size 12: 12 AWG 334 N75 lbf
  • 14 AWG 311 N. Contact retention in the housing: 133 N minimum.70 lbf · 30 lbf
Sourced1922
Application spec

Connector: 114-151012 rev A. Solid contacts: 114-151004 rev E1. Stamped size 12 contacts are covered by 114-151002 / 114-151006 (not reviewed; the library lists only solid DTP contacts). Tool: 0425-071-0000 rev D (HDT-48-00).

Sourced161920

Assembly

  1. Check the insulation OD fits the DTP seal: 10-14 AWG, N-seal 3.40-4.32 mm, E-seal option 2.46-4.01 mm.16
  2. Strip 5.64-7.21 mm and check for damaged strands.1920
  3. Set the HDT-48-00 dial to the wire size, insert the wire until strands show in the inspection hole with a 0.63-2.54 mm gap to the insulation, and crimp until the ratchet releases.2019
  4. Hold the contact about 25 mm behind the barrel, grommet towards you, and push straight in until it stops and locks. Tug the wire lightly to confirm.16
  5. Fit a sealing plug in every unused cavity, flush with the opening.16
  6. Push the WP- wedge lock in until it snaps into the locked position (pliers can help on receptacles; plugs by hand).16

Removal

  1. Grip the wedge lock with small long-nose pliers and pull it straight out. Avoid damaging its inner ribs if it will be reused.16
  2. Push the DT-RT1 screwdriver tip or a small flat screwdriver into the cavity to release the locking finger.1621
  3. Pull the wire until the contact comes out, holding the rear grommet in place if needed.16
  4. If the grommet came out, inspect and replace it if damaged.16

Summarised in our own words from the maker's application specifications and instruction sheets cited above. Disconnect the battery before working on a vehicle harness. A crimp is only as good as its pull test: check samples with your tool and wire before building a loom. Choosing a crimp tool →

Kit parts for this family

ItemPart numberDescriptionWireQtySource
Cavity plug114017Sealing plug, white PBT, size 12/16 - the plug TE specifies for DTPAllper unused cavity16
BootDTP2P-BTSlip-on PVC boot for DTP 2-way receptacle (gray; DTP2P-BT-BK black)All116
BootDTP4P-BTSlip-on PVC boot for DTP 4-way receptacle (gray; DTP4P-BT-EN long)All116
Backshell180-DTP04Straight backshell for DTP06-4S (16 mm corrugated tubing); 90-degree versions A90-DTP04, B90-DTP04 (and -952B variants)Spec drawing shows the straight version as '2 REQD'. TE lists no DTP plug boots.All1Medium16
Crimp toolHDT-48-00Hand crimp tool for solid size 12 contacts12-14 AWG11120
Removal toolDT-RT1Removal tool for front-release connectorsAll11621
Other0413-214-1205Keying pin, yellow PBT (optional)Allas needed16

Where it's used

Our harness designs

Not used in our current harness designs.

Sensors that mate with it

No sensor in our sensor library lists this connector yet.

Factory (OEM) use

No factory ECU in our pinout library uses this connector family.

Frequently asked

What is a Deutsch DTP connector?

A Deutsch DTP connector is a sealed wire-to-wire power connector in TE's DT family. It uses size 12 contacts rated at 25 A each, comes in 2 way and 4 way housings, seals to IP68 and IP6K9K, and works from -55 to 125 °C. Separate orange wedge locks hold the contacts.71012

How many amps is a Deutsch DTP connector rated for?

TE rates DTP contacts at 25 A maximum each, with a 200 V AC/DC operating voltage. That is close to double the 13 A of a DT size 16 contact. The rating applies per contact, so size the wire, fuse and voltage drop for the real load and run length.736

What wire size fits a Deutsch DTP connector?

The standard DTP contacts, 0460-204-12141 pins and 0462-203-12141 sockets, take 12-14 AWG wire. A Mouser launch note quotes 10-14 AWG for the series, but no 10 AWG contact was confirmed here. Insulation must measure 3.4-4.3 mm on receptacles or up to 4.9 mm on plugs.Medium342710

What is the difference between Deutsch DT and DTP?

DT uses size 16 contacts rated 13 A in 2 to 12 way housings; DTP uses size 12 contacts rated 25 A in 2 and 4 way housings. DTP housings are larger and take thicker insulation. Contacts, wedges and housings are specific to each series and do not interchange.Medium672

Which wedge does a DTP06-2S use?

DTP06-2S uses the WP-2S wedge lock, an orange PBT secondary lock that TE lists for 2-way DTP plugs. The matching DTP04-2P receptacle uses WP-2P. Fit the wedge after both contacts have clicked into the housing, and use the matching 4-way wedges on 4-way housings.13129

Keep going

Related

Sources

25 sources
  1. 114017 sealing plug, size 12 and 16 · BuyDeutsch (distributor) · vendor-doc · retrieved 2026-10-27
  2. Mouser offers wide inventory of DEUTSCH DT family of cable-to-cable connectors from TE Connectivity · Elektor Magazine · press · retrieved 2026-10-27
  3. 0460-204-12141 size 12 solid pin, nickel · TE Connectivity · vendor-doc · retrieved 2026-10-27
  4. 0462-203-12141 size 12 solid socket, nickel · TE Connectivity · vendor-doc · retrieved 2026-10-27
  5. DT-RT1 contact removal tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  6. DT04-2P product page (DEUTSCH DT receptacle, 2 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  7. DTP04-2P product page (DEUTSCH DTP receptacle, 2 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  8. DTP04-4P product page (DEUTSCH DTP receptacle, 4 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  9. DTP06-2S product page (DEUTSCH DTP plug, 2 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  10. DTP06-4S product page (DEUTSCH DTP plug, 4 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  11. HDT-48-00 hand crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  12. WP-2P wedge lock product page (DTP, 2 way receptacle) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  13. WP-2S wedge lock product page (DTP, 2 way plug) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  14. WP-4P wedge lock product page (DTP, 4 way receptacle) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  15. WP-4S wedge lock product page (DTP, 4 way plug) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  16. Application Specification 114-151012 DEUTSCH DTP Series Connector System, rev A (26 Aug 2020) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  17. Product Specification 108-151012 DEUTSCH DTP Series, rev C · TE Connectivity · vendor-doc · retrieved 2026-10-27
  18. DTP06-2S product page (documents tab) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  19. Application Specification 114-151004 DEUTSCH Size 4-20 Solid Pin and Socket Contacts, rev E1 (14 Sep 2022) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  20. Instruction Sheet 0425-071-0000 DEUTSCH Field Maintenance Crimp Tool HDT-48-00, rev D (15 Jan 2018) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  21. Instruction Sheet 408-151008 DEUTSCH Removal Tool DT-RT1 for Front-Release Connectors, rev B (22 Jan 2015) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  22. Product Specification 108-151004 DEUTSCH Solid Contacts (HD), rev E (20 Aug 2020) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  23. Application Specification 114-151000 DEUTSCH Size 16 S&F Pin and Socket Contacts, rev R (08 Aug 2025) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  24. Instruction Guide 0425-037-0000 for DTT-16-00, rev D · TE Connectivity · vendor-doc · retrieved 2026-10-27
  25. Instruction Guide 0425-072-0000 for DTT-20-00, rev A · TE Connectivity · vendor-doc · retrieved 2026-10-27

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.