Wiring guide

Crimp tools: open barrel vs closed barrel, Deutsch tools and pull testing

An open barrel crimp tool rolls the two wire-barrel wings of a stamped terminal into the strands (an F-crimp) and closes a second set of wings around the insulation. Closed-barrel solid contacts, such as Deutsch machined pins, need an indent crimper instead: TE's HDT-48-00 makes a 4-indent crimp on size 12, 16 and 20 solid contacts. Deutsch stamped contacts use the DTT-16-00 and DTT-20-00 hand tools.761089

Key takeaways

  • Match the tool to the contact: F-crimp for stamped and formed, indent crimp for solid machined contacts.
  • HDT-48-00 is TE's 4-indent hand tool for size 12, 16 and 20 Deutsch solid contacts.
  • DTT-16-00 and DTT-20-00 are size-specific tools for Deutsch stamped contacts; TE lists both as superseded.
  • A good 18 AWG crimp holds at least 89 N (20 lbf) in TE's pull test, the same figure Cirris lists for UL 486A.
  • Check crimp height, bellmouth and brush on every setup, then pull-test samples.

Open barrel vs closed barrel contacts

Stamped and formed contacts start as flat strip with open wings.

Contact style, crimp form and Deutsch hand tool653241089
Contact styleExample (TE)Crimp formHand tool
Stamped and formed, size 201060-20-0122 pinF-crimpDTT-20-00
Stamped and formed, size 161060-16-0122 pinF-crimpDTT-16-00
Solid, size 200460-202-20141 pinIndent crimpHDT-48-00
Solid, size 160460-202-16141 pinIndent crimpHDT-48-00
Solid, size 120460-204-12141 pinO-crimp (TE listing)HDT-48-00

An open barrel crimp tool folds the wings into the strands and a second pair onto the insulation, which TE calls an F-crimp on its Deutsch stamped contacts.56

Solid contacts are machined with a closed tube for the wire. They take an indent crimp: TE lists its size 16 and 20 solid contacts as indent crimp and its size 12 solid pin as an O-crimp.234

Deutsch crimp tools

For a Deutsch crimp tool, start from the contact style.

HDT-48-00
  • Closed barrel, 4 indent
  • Contact sizes 12, 16, 20solid
  • Instruction sheet 0425-071-0000
Sourced10
DTT-20-00
  • Size 20 stamped contacts
  • Ratchet operator releasable and adjustable
  • Status superseded
Sourced9
DTT-16-00
  • Size 16 stamped contacts
  • Ratchet operator releasable and adjustable
  • Status superseded
Sourced8
Wire range per tool

Set by the contact: 22-16 AWG for 1060-20-0122, 18-14 AWG for 1060-16-0122

TE's DTT-20-00 and DTT-16-00 pages do not list a wire range; the figures are the ranges of the matching TE contacts.Researched, unverified65

HDT-48-00 is TE's closed-barrel, 4-indent hand tool for size 20, 16 and 12 solid contacts, with a fixed die and a ratchet that is neither releasable nor adjustable.10

DTT-20-00 and DTT-16-00 are straight-action tools for size 20 and size 16 stamped contacts, with an operator-releasable, adjustable ratchet. TE lists both as superseded, so confirm the current replacement with TE or a distributor before buying.98

Anatomy of a good open barrel crimp

TE's application specification for FASTON flag receptacles shows what to check on any open barrel crimp.

Inspection points and the limits TE sets for one terminal family (114-143089)7
FeatureWhat to look forLimit in 114-143089
Wire end extrusion (brush)Strands just past the front of the wire barrel0.38-1.14 mm (0.015-0.045 in)
Front bellmouthFlare at the mating end of the wire barrel0.7 mm (0.028 in) max
Rear bellmouthFlare at the wire entry, prevents strand nicks0.2-0.7 mm (0.008-0.028 in)
Cut-off tabLeftover carrier strip0.5 mm (0.020 in) max
Wire barrel flashMetal squeezed out at the sides0.13 mm (0.005 in) max
Wire locationNo strands outside the barrel; insulation not in the wire barrelVisual

Limits are for the FASTON flag receptacles in that specification. Use the application specification for your own terminal.

The strands must stay inside the wire barrel, the insulation must stop short of it, and both must be visible in the gap between the two barrels.7

The insulation wings should wrap the jacket firmly without cutting it. They support the wire against vibration; they are not what carries the pull load.Medium7

Crimp height

Crimp height is the finished height of the wire barrel, measured with a crimp micrometer after filing off any flash.

Micrometer vs cross-section

Micrometer readings run about 0.10-0.15 mm (0.004-0.006 in) lower than a squared cross-section measurement

Sourced7
Applicator setup tolerance

Front and rear wire barrel crimp heights within ±0.05 mm (±0.002 in) of nominal

Sourced7

TE wants front and rear readings within 0.05 mm (0.002 in) of each other; a bigger gap points to worn tooling or a bad setup.7

A cross-section confirms it

TE accepts a 10-30% reduction in the wire's area on these terminals. Set the wire barrel height first, check pull strength, then close the insulation crimp until it grips.7

Pull test: minimum pull-out force

A pull test loads the crimp until the wire breaks or pulls out.

IPC/WHMA-A-620 pull-force tablePublished in the standard for each wire sizeWe could not read the IPC/WHMA-A-620 table on a public page; the values below come from TE and from Cirris's summary of the other standards.Researched, unverified
Minimum crimp pull-out force by wire sizeMedium71
AWGTE 114-143089 (N / lbf)UL 486A terminals (lbf, per Cirris)SAE AS7928 Table II (lbf, per Cirris)
2422 / 5510
2236 / 8815
2058 / 131319
1889 / 202038
16133 / 303050
14222 / 505070
12311 / 7070110

The TE column is from the application specification. The UL and AS7928 columns are Cirris's summary, which asks readers to check the standards themselves.

TE's method disables the insulation crimp, pulls at 25.4 mm/min (1 in/min) or holds a dead weight for one minute, and counts only wire-from-barrel separation below the limit as a failure.7

TE's minimums for that terminal match the UL 486A column in Cirris's summary. Aerospace limits (SAE AS7928) are higher.71

Common crimping mistakes

Using pliers or an open barrel tool on a solid contact is the classic one: the indent tool exists because a machined barrel does not fold. The reverse also fails, since an indent die cannot form F-crimp wings.Medium105

Insulation inside the wire barrel, strands outside it and a missing rear bellmouth are all rejects in TE's inspection list. Each one shows up in a magnifier before the connector is assembled.7

Frequently asked

What is an open barrel crimp tool?

An open barrel crimp tool is a ratcheting crimper with dies that roll the open wings of a stamped terminal into the wire strands and around the insulation, forming an F-crimp. It suits stamped and formed contacts, such as TE's 1060-16-0122 Deutsch pin. Solid machined contacts need an indent tool instead.510

What crimp tool do I need for Deutsch connectors?

It depends on the contact. Deutsch solid contacts in sizes 12, 16 and 20 use TE's HDT-48-00, a 4-indent closed-barrel hand tool. Stamped and formed contacts use DTT-20-00 for size 20 and DTT-16-00 for size 16. TE lists both DTT tools as superseded, so check the current replacement before ordering.1098

Can I crimp Deutsch solid pins with an open barrel crimper?

No. Solid Deutsch contacts have a closed, machined wire barrel that TE specifies for an indent crimp, made by a tool such as HDT-48-00. An open barrel die is shaped to fold wings and will crush or split a closed barrel. Use stamped contacts if you want to use an F-crimp tool.Medium2105

How strong should a crimp be in a pull test?

TE's application specification 114-143089 sets minimums of 58 N (13 lbf) for 20 AWG, 89 N (20 lbf) for 18 AWG, 133 N (30 lbf) for 16 AWG and 222 N (50 lbf) for 14 AWG. Cirris lists the same values under UL 486A. Aerospace SAE AS7928 limits are higher.71

What is crimp height?

Crimp height is the height of the finished wire barrel, measured with a crimp micrometer across the crimp after removing any flash. It is the main setup check for an open barrel crimp. TE expects front and rear readings within 0.05 mm of each other and confirms the result by cross-section.7

Keep going

Related

Sources

10 sources
  1. Crimp pull testers: pullout force per wire size (summary of AS7928, UL 486A/486C, DIN 41611-3, NASA-STD-8739.4) · Cirris Systems · reference · retrieved 2026-10-27
  2. 0460-202-16141 pin, solid, size 16, nickel: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  3. 0460-202-20141 pin, solid, size 20, nickel: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  4. 0460-204-12141 pin, solid, size 12: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  5. 1060-16-0122 pin, stamped and formed, size 16: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  6. 1060-20-0122 pin, stamped and formed, size 20: product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  7. Application Specification 114-143089 rev H1, FASTON standard flag receptacle terminals with 2D crimp · TE Connectivity · vendor-doc · retrieved 2026-10-27
  8. DTT-16-00 hand crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  9. DTT-20-00 hand crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  10. HDT-48-00 hand crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.