TE Connectivity (AMP)

TE Superseal 1.0 connectors

AMP Superseal 1.0 mmSuperseal 1.0 connectorSuperseal 26 / 34 / 60 way

A Superseal connector, in its 1.0 mm form, is TE's sealed wire-to-board system for modules and ECUs. Black plug housings with 26 or 34 cavities on a 3.0 mm pitch mate with PCB pin headers of 26, 34 or 60 pins. TE rates the system at up to 15 A per contact, 250 V and -40 to 125 °C.12

At a glance

Plug sizes
  • 26 and 34 way
  • 60-way headers take one of each
Sourced1
Contact1.0 mm stamped double-spring receptacleSourced15
CurrentUp to 15 A per contactconsult 108-78140Sourced15
Wire range0.5-1.25mm²20-16 AWGSourced65
Pitch3.0mm0.118 inSourced2
Temperature-40 to 125°C-40 to 257 °FSourced12
Voltage
  • 250 V AC/DC
  • Withstands 1000 V AC for 1 minute
Sourced1
Sealing
  • Immersion per JIS D0203
  • Silicone grommet
Sourced12
CodingKeys 1 to 4 on 26 way, Keys 1 and 2 on 34 waySourced1

Part numbers

What a Superseal 1.0 connector is

The Superseal connector family from TE (originally AMP) covers several contact sizes.

The 1.0 mm version is the multi-pin wire-to-board system: a sealed plug on the harness mates with a pin header soldered to a circuit board.Medium12

Plugs carry a silicone grommet, a seal ring and a white final lock that confirms every contact is seated. Headers come with straight or right-angle pins and with upper, lower or double locking latches.14

Plug sizes and dimensions

TE lists two plug sizes.

Sources disagreeSuperseal 1.0 plug housing, reference dimensions from the TE catalog (mm).Medium1
CavitiesLengthHeightWidth
2632.134.532.1
3432.138.038.2

TE's product page and drawing for the upper-lock 34-way plugs 4-1437290-0 / -1 give a height of 34.55 mm; the catalog's 38.0 mm matches the double-lock drawing. Height depends on the latch style.

The 34-way plug is the larger, with four rows of 9, 8, 8 and 9 cavities.14

34-way plugs and their headers

Two 34-way plugs with the same contacts differ only by coding key.

34-way plug to header pairs from the TE catalog and drawing 2-1437285-3.14
PlugKeyLockExample headers
4-1437290-01Single latch6437288-1 (upper), 2-6437285-5 (lower), 2-6447232-3 (vertical)
4-1437290-12Single latch6437288-2 (upper), 2-6437285-6 (lower), 2-6447232-4 (vertical)
2-1437285-31Double3-6437285-0
3-1437290-92Double3-6437285-1

Use a different key on each header when a module has two side by side.13

Superseal 1.0 contacts and tools

Two receptacle contacts cover the wire range.

Cavity plug4-1437284-3Sourced17
Extraction toolNot confirmedNo TE or distributor page naming a Superseal 1.0 extraction tool was found. Superseal 1.5 tools are a different size.Researched, unverified
Superseal 1.0 receptacles and tooling from TE.156
PartWireInsulation ODCurrent (typical)Hand toolApplicator
3-1447221-40.5 mm² (20 AWG)1.6-1.9 mm6 A1454509-12151705-1 / -2
3-1447221-30.75-1.25 mm² (18-16 AWG)1.6-2.2 mm15 A1454509-12151705-1 / -2

Insulation ranges from TE product pages; the catalog table lists slightly wider ranges.

Both have a gold contact area and a tin crimp area, and both are family-seal parts, so no single-wire seals are needed.156

How to assemble a Superseal 1.0 plug

Crimp each receptacle with the tool for its wire size, then insert it from the wire side until it locks.

On 34-way plugs, put 1.25 mm² wires only in positions 1, 9, 10, 17, 18, 25, 26 and 34.41

Fill every empty cavity with a 4-1437284-3 plug, then close the white final lock. If it will not close, a contact is short.Medium14

Common mistakes

Fitting 1.25 mm² wire with 2.0-2.2 mm insulation in an inner cavity.

Only the eight outer positions take that size; elsewhere the seal will not close on it.4

Ordering the wrong key. Key 1 and Key 2 plugs look the same but will not cross-mate.1

Mixing in Superseal 1.5 parts. The 1.5 series is a separate TE range with its own contacts and tools, so order by the 1.0 part numbers listed here.Low1

CAD and drawings

We link to the maker's own downloads and do not rehost drawings, 3D models or specifications: the makers' terms grant no redistribution. Our cavity maps are drawn from the cavity numbers, never traced from these drawings.

Crimp and assembly quick card

Strip length3.5mm +1.0/-0reference valueSourced8
Crimp height
  • Wire barrel: 0.5 mm² 0.90 ±0.05 mm (width 1.60 ±0.1, 3-1447221-4)
  • 0.75 mm² 1.00 ±0.05
  • 0.85 mm² 1.05 ±0.05
  • 1.0 mm² 1.10 ±0.05
  • 1.25 mm² 1.20 ±0.05 mm (width 1.85 ±0.1, 3-1447221-3). Insulation barrel: 2.2 mm max height / 2.3 mm max width up to 0.85 mm²
  • 2.5 / 2.6 mm max for 1.0-1.25 mm²
Sourced8
Pull-out force (minimum)
  • 0.5 mm²: 88.2 N min9 kgf
  • 0.75 mm² AVSSX/AESSX: 117.6 N12 kgf
  • 0.85 mm²: 127.4 N13 kgf
  • 1.0 mm² ISO 19642-3 thin wall: 147 N15 kgf
  • 1.25 mm²: 176.4 N18 kgf
114-78016 gives lower minimums (50 / 90 / 110 N) for the specific ACW0219 cable; use the figure for your wire type.Sourced810
Application spec
  • 114-78011 rev A125 Mar 2025
  • 114-78016 rev A covers ACW0219 wire only
Sourced89

Assembly

  1. Strip about 3.5 mm (up to 4.5 mm) without nicking strands or scarring the insulation.8
  2. Crimp with the TE applicator for the contact (2151241-1 for 3-1447221-3, 2151705-1 for 3-1447221-4) and check wire- and insulation-barrel height against 114-78011.8
  3. Check the crimp: conductor protrudes 0.3-0.8 mm past the wire barrel, bell-mouth 0.2-0.4 mm, seam closed, bend and twist within 3° (rolling 6°).8
  4. Hold the contact near the crimp and push it straight into the wire side of the plug until it bottoms; a deformed contact must be scrapped and a new one crimped.11
  5. Check every contact from the mating face and the wire face, and fit hole plug 4-1437284-3 in unused cavities.1110
  6. Press both final-lock protrusions in together with your fingers until they latch; if they stop part way a contact is not fully home, so recheck it rather than forcing the lock.11
  7. Route wires so no single wire is under tension; make any 90° bend about 20 mm from the connector.11

Removal

  1. Release the final lock by lifting its release side with a fingernail or small flat-blade screwdriver until it clicks out; TE limits this to 10 releases.11
  2. Confirm both final-lock protrusions stand proud, then pull the wire straight back out of the housing; TE limits removal of one position to 3 times.11
  3. TE's instruction sheet names no dedicated extraction tool for Superseal 1.0.Medium11

Summarised in our own words from the maker's application specifications and instruction sheets cited above. Disconnect the battery before working on a vehicle harness. A crimp is only as good as its pull test: check samples with your tool and wire before building a loom. Choosing a crimp tool →

Kit parts for this family

ItemPart numberDescriptionWireQtySource
Terminal2461132-1 / 2461132-2Silver-plated alternatives to 3-1447221-3 / -4 (0.75-1.25 / 0.5 mm²) on the same crimp spec0.5-1.25 mm²1 per wire8
Terminal1-2461132-1 / 1-2461132-2Tin-plated alternatives to 3-1447221-3 / -40.5-1.25 mm²1 per wire8
SealNone (no separate wire seal)The 34-way plug is supplied as a sealed housing assembly; TE's parts list and instruction sheet list only contacts, housings and the hole plug, so no single-wire seals are boughtInferred from the parts lists (no seal part exists) plus 'do not dismantle the housing'. Neither document uses the words family seal or mat seal.All0Medium1011
Cavity plug4-1437284-3Hole (cavity) plug for unused 1.0 mm cavitiesPart number confirmed by 108-78140 and 411-78017 (old P/N 3400130). Colour still conflicts: TE catalog says white, TE product page says natural POM; 108-78140 does not state a colour.Allper unused cavitySources disagreeMedium101117
Crimp tool2151241-1OCEAN applicator for 3-1447221-3 / 2461132-1 / 1-2461132-1114-78011 lists 2151705-1 for the small-barrel 0.5 mm² contacts only, while the existing data lists 2151705-1/-2 for both contacts; treat 2151241-1 as the normal-barrel applicator.16-18 AWG18
Crimp tool1454509-1Straight-action hand tool, Super Seal receptacle (alias 3800088-01)TE marks it superseded and not currently available; no replacement named. 114-78016 lists hand-tool applicators 1463173-2 / 1463174-2 for the AMP-O-Lectric terminator.All112
Removal toolNone requiredContacts come out by pulling the wire once the final lock is released; a small flat-blade screwdriver can lift the lockAll1Medium11

Where it's used

Our harness designs

  • ECU2 harness (concept) Design, pre-release4-1437290-0 at Connector A: 34-way Key 1 plug. For the ECU2.13
  • ECU2 harness (concept) Design, pre-release4-1437290-1 at Connector C: 34-way Key 2 plug, so it cannot be swapped with connector A. For the ECU2.13

Sensors that mate with it

No sensor in our sensor library lists this connector yet.

Factory (OEM) use

No factory ECU in our pinout library uses this connector family.

Frequently asked

What is a Superseal 1.0 connector used for?

Superseal 1.0 is a sealed wire-to-board connector. TE designed it for printed circuit board applications in harsh environments, which suits sealed electronic modules: the harness plug mates with a pin header soldered to the module's board. TE rates it at 250 V and -40 to 125 °C, with immersion sealing per JIS D0203.12

What terminals fit Superseal 1.0 plugs?

Superseal 1.0 plugs take TE's 1.0 mm stamped double-spring receptacles. Use 3-1447221-4 for 0.5 mm² (20 AWG) wire and 3-1447221-3 for 0.75-1.25 mm² (18-16 AWG). Both have a gold contact area. TE lists 6 A and 15 A typical respectively, and both seal through the housing grommet.561

What is the difference between Superseal Key 1 and Key 2?

Only the coding. A Key 1 plug such as 4-1437290-0 mates only with Key 1 headers, and a Key 2 plug such as 4-1437290-1 only with Key 2 headers. Contacts, pitch and size are the same. Modules with two 34-way headers use one of each so the plugs cannot be swapped.123

How many amps can a Superseal 1.0 contact carry?

TE quotes up to 15 A for the Superseal 1.0 contact system and points to product specification 108-78140 for the derating detail. The 0.75-1.25 mm² receptacle 3-1447221-3 lists 15 A typical, while the 0.5 mm² receptacle 3-1447221-4 lists 6 A typical, so size the wire to the load.156

Keep going

Related

Sources

13 sources
  1. Superseal 1.0 Connectors (TE catalog section, distributor-hosted) · TE Connectivity, hosted by Dalroad · vendor-doc · retrieved 2026-10-27
  2. 4-1437290-0 product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  3. 4-1437290-1 product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  4. Customer drawing 2-1437285-3 rev P (Superseal plug housing 34 pos, sheets 1-4) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  5. 3-1447221-3 Superseal 1.0 receptacle product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  6. 3-1447221-4 Superseal 1.0 receptacle product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  7. 4-1437284-3 Superseal 1.0 sealing plug product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  8. Application Specification 114-78011 rev A1 (25 Mar 2025): Super Seal contacts · TE Connectivity · vendor-doc · retrieved 2026-10-28
  9. Application Specification 114-78016 rev A (17 Oct 2018): Super Seal connector for ACW0219 wire · TE Connectivity · vendor-doc · retrieved 2026-10-28
  10. Product Specification 108-78140 rev A9 (11 Oct 2021): Superseal 1.0 connector · TE Connectivity · vendor-doc · retrieved 2026-10-28
  11. Instruction Sheet 411-78017 rev O (10 Oct 2001): Super Seal plug housing connector · TE Connectivity (Tyco Electronics AMP K.K.) · vendor-doc · retrieved 2026-10-28
  12. 1454509-1 straight action hand tool, Super Seal receptacle contact (product page) · TE Connectivity · vendor-doc · retrieved 2026-10-28
  13. internal GAINS internal: GAINS universal harness designs v1: Single Controller and IO Module harness build scripts, connector lists and wire lists (pre-release, not yet built)

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.