TE Connectivity (AMP)

TE AMPSEAL connectors

AMPSEAL 23AMPSEAL 35AMPSEAL 1.3 mmAMP AMPSEALAMPSEAL 16

An AMPSEAL connector is TE Connectivity's sealed, rectangular wire-to-board connector built on 1.3 mm stamped socket contacts at a 4 mm pitch. The plugs come in 8, 14, 23 and 35 positions. TE rates the 23- and 35-way plugs at 17 A maximum per contact, 250 V, -40 to 125 °C and IP67/IP69K. The separate AMPSEAL 16 series uses size 16 contacts in 2 to 12 positions.13411

At a glance

Positions8,14, 23 and 35plug assembliesSourced12
Contact1.3 mm stamped and formed socket, F-crimp (open barrel)Sourced62
Pitch

4 mm (0.157 in) centreline and row-to-row, 3 rows on 23 and 35 way

Sourced34
CurrentUp to 17 A with gold contacts, up to 8 A with tin contactsSourced187
Wire range
  • 20-16 AWG on the common 770520 / 770854 contacts0.5-1.3 mm²
  • TE's series page quotes 16-24 AWG for the family
The contact pages list 20-16 AWG. The family page lists 16-24 AWG and two different mm² ranges, which implies a small-wire contact we did not find. Pick the contact by part number for your gauge.Conflict671
Insulation OD1.7-2.7mm0.067-0.106 inSourced67
Voltage250VSourced34
Temperature
  • Plug housings -40 to 125 °C-40 to 257 °F
  • The tin contact pages list -40 to 105 °C (-40 to 221 °F)
TE's housing and contact pages publish different upper limits. Use the lower figure for the assembled connector unless TE's product specification 108-1329 says otherwise.Conflict36
Sealing
  • IP67 and IP69Kplug housings
  • Empty cavities stay sealed
Sourced310
Secondary lock
  • Red wedge lock built into the plug
  • No separate part to buy
Sourced10

What an AMPSEAL connector is

The AMPSEAL connector is a sealed plug that mates straight onto a header soldered to a circuit board.

Housing materialPBT, black, UL 94V-0776164-1, 770680-1Sourced34
Keying
  • Keying code A on the black 23- and 35-way plugs
  • Other codes exist as separate part numbers
Sourced34
Primary lockRetention fingers integrated in the housingSourced310

TE sells it for harsh, under-hood and off-highway use, so it often sits on control modules rather than in the middle of a harness.12

Each plug arrives as one assembly

Housing, cover, wire seals, mating seal and a red wedge lock. A wire seal sits in every cavity. The contact pierces it on the way in, so you do not need cavity plugs for unused positions.10

Plug sizes and ratings

The 23- and 35-way plugs share the same height and width; the 35-way is longer.

Mating header example

776087-1: 23-position right-angle PCB header, tin pins, 8 A, -40 to 105 °C

Sourced5
AMPSEAL 23- and 35-way plug housings (black, key A), per TE product pages43
PlugPositionsRowsL x W x HMax current per contactSealing
770680-123347.4 x 33.6 x 34.6 mm (1.866 x 1.323 x 1.362 in)17 AIP67, IP69K
776164-135363.4 x 33.6 x 34.6 mm (2.496 x 1.323 x 1.362 in)17 AIP67, IP69K

Both carry socket contacts and mate with 1.3 mm pin headers in vertical or right-angle form.3451

Contacts and tools

The plating sets the current rating.

AMPSEAL 1.3 mm contacts and tooling678910
Part numberWhat it isWire / rangePlatingRating or note
770520-1Socket contact, reel20-16 AWG (0.517-1.31 mm²), insulation 1.7-2.7 mmTin8 A typical
770854-1Socket contact, loose piece20-16 AWG (0.517-1.31 mm²), insulation 1.7-2.7 mmTin8 A typical
770854-3Socket contact, loose piece20-16 AWG (0.517-1.31 mm²), insulation 1.7-2.7 mmGold17 A typical
58529-1PRO-CRIMPER III hand crimp toolAMPSEAL 1.3 mm contacts-Open barrel F-crimp
770678-1Seal plugRe-seals a cavity pierced by mistake-Nylon 6/6
No toolContact removalScrewdriver 2-5 mm wide opens the wedge-Per TE 408-3229

TE lists the tin 770854-1 at 8 A typical and the gold 770854-3 at 17 A typical on the same 20-16 AWG wire range. Choose gold when you need the full 17 A housing rating.78

There is no contact removal tool. Open the red wedge lock with a small flat screwdriver, then ease the wire out with quarter turns. TE says to discard a removed contact rather than re-crimp it.10

How to pin an AMPSEAL plug

Plugs ship with the red wedge lock open.

Instruction sheet

TE 408-3229 rev F covers plug assemblies 776268, 776273, 770680 and 776164

Sourced10
Contact crimp specTE 408-3284 (contacts 770520), packed with the productSourced10

Push each crimped contact in from the wire side until it clicks, then tug the wire lightly; TE specifies 4-9 N (about 1-2 lbf) to confirm the retention fingers caught it.10

When every contact is in, squeeze the two locking latches and press the wedge lock flush with the housing. Never pull the wedge lock fully out of the housing.102

AMPSEAL 16 is a different series

AMPSEAL 16 shares the name but not the contact.

AMPSEAL 16 headline ratings, per TE's series page11
ItemValue
Positions2, 3, 4, 6, 8, 12
ContactsSize 16 HDSF (stamped) or DEUTSCH solid
CurrentUp to 13 A per circuit, depending on wire and loading
Wire range14-20 AWG (2.5-0.5 mm²)
VoltageUp to 250 V DC
Temperature-40 to 125 °C standard; -40 to 150 °C high-temperature version
SealingIP67; IP68 and IP6K9K with a backshell
LocksIntegrated CPA and TPA in a one-piece housing; keys A-D
Durability50 mating cycles per SAE J2030

The 16 is the contact size: it takes size 16 stamped (HDSF) or DEUTSCH solid contacts in 2- to 12-position housings, so parts do not cross over with the 1.3 mm AMPSEAL.11

Where AMPSEAL connectors are used

TE lists heavy trucks, buses, electric and passenger vehicles, farm and construction control modules, emergency vehicles, off-road recreational vehicles and power distribution boxes. In race and kit-car builds you will mostly meet AMPSEAL as the header on a control module or power distribution unit.Medium1

Common mistakes

Inserting contacts with the wedge lock closed is the classic one; TE warns against it and says a hard insertion means the wedge is not fully open. Re-using a contact after cutting the wire off is the second; fit a new contact.10

Using tin contacts on a high-current pin is the third. Tin is rated 8 A typical against 17 A for gold, so check the plating on power and ground circuits.78

CAD and drawings

We link to the maker's own downloads and do not rehost drawings, 3D models or specifications: the makers' terms grant no redistribution. Our cavity maps are drawn from the cavity numbers, never traced from these drawings.

Crimp and assembly quick card

Strip length

Standard wire (20-16 AWG): 5.1 ±0.4 mm. Reduced wire (24-20 AWG): 4.3 mm (770520-5/-8) or 4.0 mm (770520-6, 1-770520-1) ±0.4

Sourced12
Crimp height
  • 770520-1/-3: 0.5 mm² 1.17 ±0.0520 AWG
  • 0.8 mm² (18) 1.27 ±0.05
  • 1.0 mm² FLRY 1.28 ±0.05
  • 1.5 mm² (16) 1.40 ±0.05 mm
  • Wire-barrel width 2.03 nominal
  • Insulation crimp 3.2 mm max height, 3.1 ±0.1 width
The table names 770520-1 and -3; 770854-3 lists 114-16016 as its application spec but is not in the table, so confirm its crimp height with TE.Sourced128
Pull-out force (minimum)TBCNot published in 114-16016TBC: no tensile table found in 114-16016 or 408-3229.Researched, unverified
Application spec114-16016rev S330 Apr 2025Sourced12

Assembly

  1. Strip 5.1 mm without nicking strands; keep the insulation within 26 mm of the contact tip smooth, as stripper-jaw marks there can leak past the wire seal.12
  2. Crimp loose-piece contacts in the TE hand tool; never cut reeled contacts into loose pieces, as the burr damages the wire seal.12
  3. Confirm the red wedge lock is open (as shipped), then push each contact straight through the cavity seal until it clicks.10
  4. Tug the wire with about 4-9 N to prove the retention fingers have caught the contact.1012
  5. Squeeze both locking latches inward and push the wedge lock in until flush with the housing.10
  6. Fit seal plug 770678-1 (large end first) only in a cavity whose diaphragm has been pierced; untouched cavities stay sealed.1012

Removal

  1. Insert a small flat screwdriver (2-5 mm blade; 114-16016 shows 4.8 mm) between the housing edge and one corner of the red wedge lock and pry it to the open position, then repeat on the other corner.1012
  2. Rotate the wire a quarter turn each way while pulling gently until the contact comes out.10
  3. Never remove the wedge lock from the housing.10

Summarised in our own words from the maker's application specifications and instruction sheets cited above. Disconnect the battery before working on a vehicle harness. A crimp is only as good as its pull test: check samples with your tool and wire before building a loom. Choosing a crimp tool →

Kit parts for this family

ItemPart numberDescriptionWireQtySource
Terminal770520-5 / 770520-8 / 770520-6 / 1-770520-1Reduced-wire-size contacts for 24-20 AWG, insulation 1.4-1.8 mm24-20 AWG1 per wire12
Cavity plug770678-1Seal plug for a pierced unused cavity (standard wire size)Allper pierced cavity12
Cavity plug776364-1AMPSEAL 16 size 20 seal plug, used with reduced-wire-size plugsAllper pierced cavity12
Crimp tool58529-1 with die 58529-2PRO-CRIMPER III hand tool (408-9999)TE product page says 58529-1 is not currently available.20-16 AWG1129
Crimp tool58440-1Hand crimping tool (408-9592)All1Medium12
Removal toolNo.1 jeweller's / 4.8 mm flat-blade screwdriverNo dedicated extraction tool; a flat screwdriver opens the wedge lockAll112

Where it's used

Our harness designs

Not used in our current harness designs.

Sensors that mate with it

No sensor in our sensor library lists this connector yet.

Factory (OEM) use

No factory ECU in our pinout library uses this connector family.

Frequently asked

What pins fit an AMPSEAL connector?

AMPSEAL plugs take TE's 1.3 mm stamped socket contacts. The common ones are 770520-1 on a reel and 770854-1 loose, both tin and both for 20-16 AWG wire with 1.7-2.7 mm insulation. The gold 770854-3 covers the same wire range and carries a higher rating, 17 A typical against 8 A for tin.678

How do you remove pins from an AMPSEAL connector?

You do not need a removal tool. Slide a 2-5 mm flat screwdriver between the housing edge and one corner of the red wedge lock and pry it out to its open position, then repeat on the other corner. Pull the wire gently while turning it a quarter turn each way until the contact comes out. TE says to fit a new contact afterwards.10

What crimp tool is used for AMPSEAL contacts?

TE's hand tool for the 1.3 mm AMPSEAL contacts is the 58529-1 PRO-CRIMPER III, which makes the open-barrel F-crimp the contacts use. TE also sells applicators for production presses. The contact crimp procedure is in TE instruction sheet 408-3284, which ships with the 770520 contacts.9610

Do unused AMPSEAL cavities need plugs?

No. Every cavity has its own wire seal that stays closed until a contact pierces it, so empty positions remain sealed. TE's 770678-1 seal plug is only for a cavity you pierced by mistake: push it in large end first as far as it will go to re-seal that position.10

What is the difference between AMPSEAL and AMPSEAL 16?

They are separate series. AMPSEAL uses 1.3 mm stamped sockets at a 4 mm pitch in 8- to 35-way plugs that mate with PCB headers. AMPSEAL 16 uses size 16 stamped or DEUTSCH solid contacts in 2- to 12-way housings, rated up to 13 A on 14-20 AWG wire. The contacts and housings do not interchange.111

Keep going

Related

Sources

12 sources
  1. AMPSEAL connectors (series page) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  2. AMPSEAL connector overview and assembly instructions · TE Connectivity · vendor-doc · retrieved 2026-10-27
  3. 776164-1 AMPSEAL 35-position plug housing · TE Connectivity · vendor-doc · retrieved 2026-10-27
  4. 770680-1 AMPSEAL 23-position plug housing · TE Connectivity · vendor-doc · retrieved 2026-10-27
  5. 776087-1 AMPSEAL 23-position right-angle PCB header · TE Connectivity · vendor-doc · retrieved 2026-10-27
  6. 770520-1 AMPSEAL 1.3 mm socket contact · TE Connectivity · vendor-doc · retrieved 2026-10-27
  7. 770854-1 AMPSEAL socket contact, tin · TE Connectivity · vendor-doc · retrieved 2026-10-27
  8. 770854-3 AMPSEAL socket contact, gold · TE Connectivity · vendor-doc · retrieved 2026-10-27
  9. 58529-1 PRO-CRIMPER III hand tool, AMPSEAL · TE Connectivity · vendor-doc · retrieved 2026-10-27
  10. Instruction sheet 408-3229 rev F, AMPSEAL automotive plug assemblies · TE Connectivity (hosted by Farnell) · vendor-doc · retrieved 2026-10-27
  11. AMPSEAL 16 connector series · TE Connectivity · vendor-doc · retrieved 2026-10-27
  12. Application Specification 114-16016 rev S3 (30 Apr 2025): AMPSEAL automotive plug connector and header assembly · TE Connectivity · vendor-doc · retrieved 2026-10-28

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.