TE Connectivity (Deutsch) · Deutsch DT

DT04-4P: Deutsch DT 4-way receptacle (pin contacts)

Deutsch DT 4-way receptacle

DT04-4P is the grey 4-way receptacle in the Deutsch DT series. It holds 4 size 16 pin contacts in two rows, mates with the DT06-4S plug and takes the green W4P wedge lock, sold separately. TE rates the contacts at 13 A maximum, the housing at -55 to 125 °C (-67 to 257 °F) and the sealed connector at IP68 and IP6K9K.1129

4-wayReceptacle, pin contacts
DT06-4SMates with
W4PWedge / secondary lock
13 A maximumCurrent
14-20 AWGWire range

DT04-4P cavity layout

latch1423
Wire side, latch up. Numbering unverified: check the moulded numbers. The mating face is the wire-side grid mirrored left to right (latch still up), derived by us. Drawn from the cavity numbers; not to scale.

Unverified No TE drawing for this DT housing could be retrieved, so the numbering is not confirmed. The grid follows the pattern on the TE drawings for the DTM receptacle and plug (receptacle numbers start top left on the wire side, plug numbers are the mirror). Read the numbers moulded on the rear of the housing before pinning.

Contact size
  • Size 16 pins
  • Mating pin diameter 1.59 mm0.063 in
Sourced1
Length45.92mm1.808 inTE product page values for the plain housing; flanged or end-cap variants differ.Sourced1
Width20.83mm0.82 inSourced1
Height19.71mm0.776 inSourced1

CAD and drawings

We link to the maker's own downloads and do not rehost drawings, 3D models or specifications: the makers' terms grant no redistribution. Our cavity maps are drawn from the cavity numbers, never traced from these drawings.

Complete kit by wire size

Everything to terminate one DT04-4P: pick the terminal for your wire size and plating. Lines marked Unverified or TBC need checking against the maker's current drawing before you order.

16-20 AWG (0.5-1.5 mm²) · Nickel · solid
ItemPart numberDescriptionQtySource
HousingDT04-4P4-way receptacle11129
Wedge / TPAW4PWedge lock / secondary lockSecondary lock, green PBT, sold separately. TE describes it as the 4-position DT receptacle wedge lock.112
Terminal0460-202-16141pin, solid (machined), indent crimp, NickelTE lists 13 A typical.4 (1 per wire)3
Cavity plug114017Sealing plug for unused size 12/16 cavities (white)Distributor listing for DT, DTM, DTP and other Deutsch series. TE's own page for 114017 could not be retrieved, and the listing gives the material as both plastic and silicone.per unused cavityMedium2
Cavity plug0413-217-1605Locking sealing plug, white PBT, N-seal and E-sealAlternative to 114017.per unused cavity14
Cavity plug776363-1Sealing plug, yellow PBT, N-seal (standard) housingsAlternative for standard-seal housings.per unused cavity14
BootDT4P-BTSlip-on PVC boot, gray; arrives closed, cut the end to suit the bundle (black: DT4P-BT-BK)PVC, -29 to +100 C: lower than the connector's 125 C rating.114
Backshell1011-237-0405PA66 backshell, straight (180 deg); takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-265-0405PA66 backshell, straight (180 deg) with strain relief; takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-238-0405PA66 backshell, right-angle (90 deg); takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-266-0405PA66 backshell, right-angle (90 deg) with strain relief; takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Crimp toolHDT-48-00Hand crimp tool for solid size 12/16/20 contacts11117
Removal toolDT-RT1Removal tool: hook end lifts the wedge lock, screwdriver end releases the locking finger11421
Removal tool0411-204-1605Size 16 extraction tool already listed in the libraryTE's DT application spec names only DT-RT1 (front release) for contact removal; no TE source found tying 0411-204-1605 to DT. Recommend dropping it from the DT kit or marking it as not required.TBCUnverifiedMedium1421
OtherM15570-16Insertion tool, size 16 (blue); may be needed for contacts on wire of 20 AWG or smaller114
Other0413-215-1605Keying pin (optional) for plug cavities to prevent mis-mating of like connectorsas needed14
OtherDT4P-DCPVC slip-on dust cap for the unmated connector1 (optional)14
16-20 AWG (0.5-1.5 mm²) · Gold · solid
ItemPart numberDescriptionQtySource
HousingDT04-4P4-way receptacle11129
Wedge / TPAW4PWedge lock / secondary lockSecondary lock, green PBT, sold separately. TE describes it as the 4-position DT receptacle wedge lock.112
Terminal0460-202-1631pin, solid (machined), indent crimp, GoldTE lists 13 A typical. Gold plating on the contact interface and crimp area.4 (1 per wire)4
Cavity plug114017Sealing plug for unused size 12/16 cavities (white)Distributor listing for DT, DTM, DTP and other Deutsch series. TE's own page for 114017 could not be retrieved, and the listing gives the material as both plastic and silicone.per unused cavityMedium2
Cavity plug0413-217-1605Locking sealing plug, white PBT, N-seal and E-sealAlternative to 114017.per unused cavity14
Cavity plug776363-1Sealing plug, yellow PBT, N-seal (standard) housingsAlternative for standard-seal housings.per unused cavity14
BootDT4P-BTSlip-on PVC boot, gray; arrives closed, cut the end to suit the bundle (black: DT4P-BT-BK)PVC, -29 to +100 C: lower than the connector's 125 C rating.114
Backshell1011-237-0405PA66 backshell, straight (180 deg); takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-265-0405PA66 backshell, straight (180 deg) with strain relief; takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-238-0405PA66 backshell, right-angle (90 deg); takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-266-0405PA66 backshell, right-angle (90 deg) with strain relief; takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Crimp toolHDT-48-00Hand crimp tool for solid size 12/16/20 contacts11117
Removal toolDT-RT1Removal tool: hook end lifts the wedge lock, screwdriver end releases the locking finger11421
Removal tool0411-204-1605Size 16 extraction tool already listed in the libraryTE's DT application spec names only DT-RT1 (front release) for contact removal; no TE source found tying 0411-204-1605 to DT. Recommend dropping it from the DT kit or marking it as not required.TBCUnverifiedMedium1421
OtherM15570-16Insertion tool, size 16 (blue); may be needed for contacts on wire of 20 AWG or smaller114
Other0413-215-1605Keying pin (optional) for plug cavities to prevent mis-mating of like connectorsas needed14
OtherDT4P-DCPVC slip-on dust cap for the unmated connector1 (optional)14
14 AWG (2 mm²) · Nickel · solid
ItemPart numberDescriptionQtySource
HousingDT04-4P4-way receptacle11129
Wedge / TPAW4PWedge lock / secondary lockSecondary lock, green PBT, sold separately. TE describes it as the 4-position DT receptacle wedge lock.112
Terminal0460-215-16141pin, solid (machined), indent crimp, NickelTE lists 13 A typical.4 (1 per wire)5
Cavity plug114017Sealing plug for unused size 12/16 cavities (white)Distributor listing for DT, DTM, DTP and other Deutsch series. TE's own page for 114017 could not be retrieved, and the listing gives the material as both plastic and silicone.per unused cavityMedium2
Cavity plug0413-217-1605Locking sealing plug, white PBT, N-seal and E-sealAlternative to 114017.per unused cavity14
Cavity plug776363-1Sealing plug, yellow PBT, N-seal (standard) housingsAlternative for standard-seal housings.per unused cavity14
BootDT4P-BTSlip-on PVC boot, gray; arrives closed, cut the end to suit the bundle (black: DT4P-BT-BK)PVC, -29 to +100 C: lower than the connector's 125 C rating.114
Backshell1011-237-0405PA66 backshell, straight (180 deg); takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-265-0405PA66 backshell, straight (180 deg) with strain relief; takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-238-0405PA66 backshell, right-angle (90 deg); takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-266-0405PA66 backshell, right-angle (90 deg) with strain relief; takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Crimp toolHDT-48-00Hand crimp tool for solid size 12/16/20 contacts11117
Removal toolDT-RT1Removal tool: hook end lifts the wedge lock, screwdriver end releases the locking finger11421
Removal tool0411-204-1605Size 16 extraction tool already listed in the libraryTE's DT application spec names only DT-RT1 (front release) for contact removal; no TE source found tying 0411-204-1605 to DT. Recommend dropping it from the DT kit or marking it as not required.TBCUnverifiedMedium1421
Other0413-215-1605Keying pin (optional) for plug cavities to prevent mis-mating of like connectorsas needed14
OtherDT4P-DCPVC slip-on dust cap for the unmated connector1 (optional)14
14-18 AWG (0.75-2 mm²); insulation 1.9-3.6 mm (0.075-0.14 in) · Nickel contact area, tin crimp area · stamped
ItemPart numberDescriptionQtySource
HousingDT04-4P4-way receptacle11129
Wedge / TPAW4PWedge lock / secondary lockSecondary lock, green PBT, sold separately. TE describes it as the 4-position DT receptacle wedge lock.112
Terminal1060-16-0122pin, stamped and formed, F-crimp, Nickel contact area, tin crimp areaTE lists 13 A typical. Supplied on reels for machine or hand crimping.4 (1 per wire)6
Cavity plug114017Sealing plug for unused size 12/16 cavities (white)Distributor listing for DT, DTM, DTP and other Deutsch series. TE's own page for 114017 could not be retrieved, and the listing gives the material as both plastic and silicone.per unused cavityMedium2
Cavity plug0413-217-1605Locking sealing plug, white PBT, N-seal and E-sealAlternative to 114017.per unused cavity14
Cavity plug776363-1Sealing plug, yellow PBT, N-seal (standard) housingsAlternative for standard-seal housings.per unused cavity14
BootDT4P-BTSlip-on PVC boot, gray; arrives closed, cut the end to suit the bundle (black: DT4P-BT-BK)PVC, -29 to +100 C: lower than the connector's 125 C rating.114
Backshell1011-237-0405PA66 backshell, straight (180 deg); takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-265-0405PA66 backshell, straight (180 deg) with strain relief; takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-238-0405PA66 backshell, right-angle (90 deg); takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Backshell1011-266-0405PA66 backshell, right-angle (90 deg) with strain relief; takes 6, 7.5, 8.5 or 10 mm convoluted tubingNot for flanged or capped housings where the dovetail is hidden.1 (optional)14
Crimp tool2388970-1Current TE hand crimp tool for stamped size 16 contacts 1060/1062-14-01, -14-10, -16-01, -16-07, -16-09114-151000 rev R names this in place of DTT-16-00, which TE marks superseded. Instruction sheet 408-35190.116
Crimp tool2390264-1Current TE hand crimp tool for stamped size 16 contacts -16-01, -16-07, -16-09 at 18 AWGInstruction sheet 408-35284.116
Crimp toolDTT-16-00Size 16 straight-action hand crimp tool (superseded)TE lists contact size 16 but not the contact style or wire range, and marks the tool superseded. Check TE instruction sheet 0425-037-0000 before using it on stamped 1060/1062-16-0122 contacts.1Medium10
Removal toolDT-RT1Removal tool: hook end lifts the wedge lock, screwdriver end releases the locking finger11421
Removal tool0411-204-1605Size 16 extraction tool already listed in the libraryTE's DT application spec names only DT-RT1 (front release) for contact removal; no TE source found tying 0411-204-1605 to DT. Recommend dropping it from the DT kit or marking it as not required.TBCUnverifiedMedium1421
Other0413-215-1605Keying pin (optional) for plug cavities to prevent mis-mating of like connectorsas needed14
OtherDT4P-DCPVC slip-on dust cap for the unmated connector1 (optional)14

Mating part and wedge

Mates withDT06-4S Medium19TE lists DT04-4P as the 4-way DT receptacle for pins and DT06-4S as the 4-way DT plug for sockets, both size 16 with a 1.59 mm mating pin. No TE page retrieved names the pair directly.
Wedge lockW4P 12Secondary lock, green PBT, sold separately. TE describes it as the 4-position DT receptacle wedge lock.
Sealing plug for unused size 12/16 cavities (white)114017 Medium2Distributor listing for DT, DTM, DTP and other Deutsch series. TE's own page for 114017 could not be retrieved, and the listing gives the material as both plastic and silicone.

Contacts by wire size and plating

Part numberTypeWirePlatingSource
0460-202-16141pin, solid (machined), indent crimp16-20 AWG (0.5-1.5 mm²)Nickel3TE lists 13 A typical.
0460-202-1631pin, solid (machined), indent crimp16-20 AWG (0.5-1.5 mm²)Gold4TE lists 13 A typical. Gold plating on the contact interface and crimp area.
0460-215-16141pin, solid (machined), indent crimp14 AWG (2 mm²)Nickel5TE lists 13 A typical.
1060-16-0122pin, stamped and formed, F-crimp14-18 AWG (0.75-2 mm²); insulation 1.9-3.6 mm (0.075-0.14 in)Nickel contact area, tin crimp area6TE lists 13 A typical. Supplied on reels for machine or hand crimping.

Ratings and specifications

Contact size
  • Size 16 pins
  • Mating pin diameter 1.59 mm0.063 in
Sourced1
Wire range

14-20 AWG (0.5-2 mm²), set by the contact: solid 16-20 AWG or 14 AWG, stamped 14-18 AWG

Sourced3456
Insulation OD2.23-3.68mm0.088-0.145 inSourced1
Current rating13 A maximum per contactSourced1
Operating voltage
  • 250 V AC/DC
  • TE lists 12, 24 and 48 V system architectures
Sourced1
Temperature-55 to 125°C-67 to 257 °FSourced1
SealingIP68 and IP6K9KsealableSourced1
HousingGlass-filled polyamide (PA GF), greySourced1
Pitch4.47 mm centreline, two rows0.176 inTE prints 4.47 mm for DT04-4P and 4.44 mm for DT06-4S; the 0.03 mm gap looks like rounding.Sourced1

Crimp and removal tools

JobPart numberTool
crimpHDT-48-00Hand crimp tool for solid size 12, 16 and 20 contacts (four-indent, closed barrel) 11
crimpDTT-16-00Size 16 straight-action hand crimp tool (superseded) Medium10TE lists contact size 16 but not the contact style or wire range, and marks the tool superseded. Check TE instruction sheet 0425-037-0000 before using it on stamped 1060/1062-16-0122 contacts.
removalDT-RT1Front-release contact removal tool (DT, DTP, DTM) 7

How to choose and check a crimp tool →

Crimp and assembly quick card

Shared by every Deutsch DT housing: the values belong to the contacts, not the housing.

Strip length
  • Solid size 16 (0460-202-16141, 0462-201-16141, 0460-215-16141, 0462-209-16141): 6.35-7.92 mm (0.250-0.312 in). Stamped size 16 (1060/1062-16-01xx): 3.81-5.08 mm0.150-0.200 in
  • The DTT-16-00 guide gives 4.45 +/- 0.64 mm (0.175 +/- 0.025 in), which sits inside that window.
Sourced15171618
Crimp height
  • Stamped 1060/1062-16-01xx (wire barrel): 14 AWG 1.35-1.43 mm
  • 16 AWG 1.22-1.30 mm
  • 18 AWG 1.19-1.27 mm
  • Crimp width 2.31-2.47 mm (insulation OD 1.91-3.56 mm). Solid contacts on HDT-48-00 (reference only, TE says validate by pull test): 0460-202-16/0462-201-16 at 18 AWG 0.85-0.94 mm at the lock indent, 1.07-1.15 mm at the entry indent
  • 0460-215-16/0462-209-16 at 14 AWG 1.06-1.31 / 1.28-1.52 mm (dial 1.5).
An older DTT-16-01 envelope drawing gives 1.22-1.32 mm height and 2.39-2.54 mm width at 18 AWG for 1060/1062-16-01; the current 114-151000 rev R values are used. The HDT-48-00 table in 114-151004 lists 0460-202-16/0462-201-16 only at 18 AWG; heights for 16 and 20 AWG on that tool are not published there.Sourced1615
Pull-out force (minimum)
  • Crimp tensile minimum, solid size 16: 14 AWG 311 N70 lbf
  • 16 AWG 156 N35 lbf
  • 18 AWG 111 N25 lbf
  • 20 AWG 67 N (15 lbf). Stamped size 16: 14-18 AWG 111 N25 lbf
  • 20 AWG 67 N. Contact retention in the housing: 111 N minimum. Pull rate 25 mm/min.15 lbf · 25 lbf
A 2009 Deutsch manual listed 89 N for solid size 16 at 20 AWG; current TE specs give 67 N.Sourced151920
Application spec

Connector: 114-151009 rev C3. Contacts: 114-151004 rev E1 (solid 0460/0462), 114-151000 rev R (stamped 1060/1062-16-01). Tools: 0425-071-0000 rev D (HDT-48-00), 0425-037-0000 rev D (DTT-16-00).

Sourced1415161718

Assembly

  1. Choose the contact by wire size and check the insulation OD fits the housing seal: standard DT (N-seal) seals 2.23-3.68 mm OD; the E-seal option seals 1.35-3.05 mm (14-20 AWG).14
  2. Strip the wire to the length for the contact type, then check for missing or damaged strands.151716
  3. Solid contacts: set the HDT-48-00 dial to the wire size, push the stripped wire into the barrel until strands show in the inspection hole, leave a 0.63-2.54 mm gap between barrel and insulation, centre the contact and close the handles until the ratchet releases.1715
  4. Stamped contacts: put the contact in the tool cavity marked for the wire size, insert the stripped wire and close the tool until the ratchet releases.1816
  5. Inspect the crimp: all strands inside the barrel, none broken, mating end straight.1516
  6. On plugs, make sure the front (interface) seal is present and seated before inserting contacts.14
  7. Hold the contact about 25 mm behind the crimp barrel, grommet towards you, and push it straight in until it stops and locks. Tug the wire lightly to confirm.14
  8. Fit a sealing plug in every unused cavity.14
  9. Push the wedge lock in until it snaps into the locked position. On receptacles a DT-RT1 or small long-nose pliers can help; on plugs it goes in by hand.14
  10. Mate plug to receptacle until the latch clicks, then check the latch is fully engaged.Medium14

Removal

  1. Unmate the connector.Medium14
  2. Plug (sockets): slide the DT-RT1 screwdriver tip under the wedge lock and lift it out evenly, taking care not to damage the front seal.1421
  3. Receptacle (pins): on 2, 4, 6 and 12-way, hook the DT-RT1 hook tip in the wedge removal slot and pull straight out; on 3 and 8-way and keyed 2/4-way wedges, grip the wedge post with small long-nose pliers.1421
  4. Push the DT-RT1 screwdriver tip (or a small flat screwdriver) into the contact's cavity to lift the locking finger off the contact.1421
  5. Holding the rear grommet in place, pull the wire back until the contact comes out.1421
  6. Inspect the grommet and wedge lock; replace any damaged part before reassembly.14

Summarised in our own words from the maker's application specifications and instruction sheets cited above. Disconnect the battery before working on a vehicle harness. A crimp is only as good as its pull test: check samples with your tool and wire before building a loom. Choosing a crimp tool →

Where it's used

Our harness designs

Not used in our current harness designs.

Sensors that mate with it

No sensor in our sensor library lists this connector yet.

Factory (OEM) use

No factory ECU in our pinout library uses this connector family.

Commonly used for

Assembly notes

Hold each crimped pin about 25 mm (1 in) behind the barrel and push it straight through the rear grommet until it clicks, then tug lightly. With every cavity filled, press the W4P wedge in from the mating face until it clicks.812

To remove a contact, pull the wedge straight out with needle-nose pliers or a hook, then release the locking finger with a small screwdriver while easing the wire back. Hold the rear seal in place, because pulling a contact can displace it.8

Fill any unused cavity with a sealing plug such as 114017 so the grommet still seals. TE states that Deutsch contacts must be crimped with Deutsch tooling, with separate tools for solid and stamped contacts.Medium82

Frequently asked

What mates with DT04-4P?

DT04-4P mates with the DT06-4S plug. Both are grey DT housings with 4 size 16 cavities; the receptacle carries pins and the other half carries sockets. Use the plug's own wedge lock, because DT wedges are specific to plug or receptacle and to the cavity count.Medium1912

Which wedge lock does DT04-4P use?

DT04-4P uses the green W4P wedge lock, which TE sells separately as a secondary lock. Fit it only after every contact has clicked into place: it seats fully only when all contacts are home, and it is what keeps them from backing out under vibration or a pull on the harness.128

What wire size fits DT04-4P?

DT04-4P takes 14-20 AWG (0.5-2 mm²) wire, but the contact sets the exact range. Solid 0460/0462 size 16 contacts cover 16-20 AWG, the 14 AWG solid versions take 14 AWG, and stamped 1060/1062-16-0122 contacts take 14-18 AWG. The wire insulation must also measure 2.23-3.68 mm across to seal in the grommet.13456

What is the current rating of DT04-4P?

TE rates DT04-4P at 13 A maximum per contact, the figure for DT size 16 contacts, with a 250 V AC/DC operating voltage. The figure applies to each contact, not the whole connector. Size the wire and the fuse for the actual load and check voltage drop on long runs.18

Keep going

Related

Sources

24 sources
  1. DT04-4P product page (DEUTSCH DT receptacle, 4 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  2. 114017 sealing plug, size 12 and 16 · BuyDeutsch (distributor) · vendor-doc · retrieved 2026-10-27
  3. 0460-202-16141 size 16 solid pin, nickel · TE Connectivity · vendor-doc · retrieved 2026-10-27
  4. 0460-202-1631 size 16 solid pin, gold · TE Connectivity · vendor-doc · retrieved 2026-10-27
  5. 0460-215-16141 size 16 solid pin for 14 AWG · TE Connectivity · vendor-doc · retrieved 2026-10-27
  6. 1060-16-0122 size 16 stamped and formed pin · TE Connectivity · vendor-doc · retrieved 2026-10-27
  7. DT-RT1 contact removal tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  8. DEUTSCH DT Series Connectors (overview and assembly video page) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  9. DT06-4S product page (DEUTSCH DT plug, 4 way) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  10. DTT-16-00 hand crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  11. HDT-48-00 hand crimp tool product page · TE Connectivity · vendor-doc · retrieved 2026-10-27
  12. W4P wedge lock product page (4 way receptacle, DT) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  13. DT04-4P product page (documents tab) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  14. Application Specification 114-151009 DEUTSCH DT Series Connector System, rev C3 (14 Oct 2024) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  15. Application Specification 114-151004 DEUTSCH Size 4-20 Solid Pin and Socket Contacts, rev E1 (14 Sep 2022) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  16. Application Specification 114-151000 DEUTSCH Size 16 S&F Pin and Socket Contacts, rev R (08 Aug 2025) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  17. Instruction Sheet 0425-071-0000 DEUTSCH Field Maintenance Crimp Tool HDT-48-00, rev D (15 Jan 2018) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  18. Instruction Guide 0425-037-0000 for DTT-16-00, rev D · TE Connectivity · vendor-doc · retrieved 2026-10-27
  19. Product Specification 108-151004 DEUTSCH Solid Contacts (HD), rev E (20 Aug 2020) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  20. Product Specification 108-151000 DEUTSCH Stamped and Formed Contacts, rev J (25 Sep 2024) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  21. Instruction Sheet 408-151008 DEUTSCH Removal Tool DT-RT1 for Front-Release Connectors, rev B (22 Jan 2015) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  22. Instruction Guide 0425-072-0000 for DTT-20-00, rev A · TE Connectivity · vendor-doc · retrieved 2026-10-27
  23. Application Specification 114-151003 DEUTSCH Size 20 S&F Pin and Socket Contacts, rev J1 (04 Jun 2026) · TE Connectivity · vendor-doc · retrieved 2026-10-27
  24. Product Specification 108-151009 DEUTSCH DT Series, rev E · TE Connectivity · vendor-doc · retrieved 2026-10-27

Facts come from manufacturer documents and distributor spec pages, read on the retrieval date shown. Part numbers and ratings change: confirm against the maker's current drawing before you order. Manufacturer names identify parts only; no affiliation is implied.