Fuel map

fuel tableVE tablebase fuel tableinjector pulse width tablefuel calibration

A fuel map is the ECU table that sets how much fuel the engine gets at each operating point, usually indexed by engine speed and load. It may hold volumetric efficiency, injector pulse width or fuel mass, and it works with a lambda target table and corrections for temperature, pressure and battery voltage.Medium341

How it works

A fuel map is a lookup table.

The ECU reads rpm on one axis and load (MAP, TPS or calculated airflow) on the other, interpolates between the nearest cells, and uses the result to set fuel each cycle.Medium31

The cell contents depend on the strategy. A VE table stores volumetric efficiency, and the ECU calculates air mass and fuel from it; a pulse-width table stores injection time directly; a torque or airflow model may store fuel mass.Medium42

VE-based maps separate the engine's breathing from the fuel target. A separate lambda target table sets the mixture, so changing target lambda does not mean retuning every cell.Medium41

Corrections stack on the base value

Intake air temperature and barometric pressure for density, coolant temperature for warm-up, and battery voltage for injector dead time.Medium15

Typical values

AxesEngine speed (rpm) by loadkPa MAP, % TPS, or airflowSourced · medium31
VE cell unitsPercent, often 30-110% on naturally aspirated enginesApproximate; depends on engineLow confidence4
Pulse-width cell unitsMilliseconds of injector open timeSourced · medium1
Lambda target units
  • Lambda or AFR
  • Lambda 1.0 = 14.7:1 on gasoline
Sourced · medium7

How an ECU uses it

Each cycle the ECU finds load and rpm, interpolates the fuel map, applies the lambda target and corrections, adds injector dead time and outputs a pulse width.Medium15

Closed-loop trims then correct the result using oxygen sensor feedback in permitted regions, while open-loop areas rely on the map alone.Medium16

How to test it

4 checks, in order.

  1. Verify sensor inputs first: MAP, IAT, coolant and battery voltage readings must be correct before any cell is changed.Medium1
  2. Enter accurate injector data, including flow and dead time, so map errors are not hiding injector errors.Medium5
  3. Log measured lambda from a wideband against target across steady-state cells and compare.Medium6
  4. Adjust cells by the ratio of measured to target lambda, smooth neighbors, then recheck.Low1

Symptoms and causes

Rich or lean in one load region

Likely causes Map cells wrong there, or a sensor error

Check Compare measured and target lambda by cell

Medium6

Fuel changes with weather

Likely causes IAT or baro correction wrong

Check Check sensor readings and correction tables

Medium1

Lean at low battery voltage

Likely causes Dead time table wrong

Check Log lambda while varying voltage

Medium5

In tuning

Build the map from good data

Correct injector characterization, a calibrated wideband and steady-state logs. Then tune transients separately.Medium56

Keep the map smooth. Jagged cells cause surging as the ECU interpolates between them.Low3

Formula and worked example

PW = PW_req × VE × (MAP / MAP_ref) × corrections + t_dead
PW
injector pulse widthms
PW_req
pulse width at 100% VE and reference pressurems
VE
volumetric efficiency from the fuel map
MAP / MAP_ref
manifold pressure ratio
t_dead
injector dead timems
Medium41

Try it

cu in
rpm
%
psi

14.7 psia at sea level wide-open throttle without boost.

°F

Result

Volumetric airflow541 CFM at manifold conditions
Mass airflow39.0 lb/min

Planning estimate from the formula below, not a measurement.

Open the full engine airflow (cfm) calculator →

Common mistakes

Mistake Tuning the fuel map before injector data is correct.

Do instead Characterize injectors first so the map holds only engine data.Medium5

Mistake Changing VE to fix a lambda target choice.

Do instead Leave VE alone; change the lambda target table.Medium41

Myths vs facts

Myth The fuel map holds air-fuel ratio.

Fact In VE strategies it holds breathing efficiency. Mixture comes from the lambda target table.Medium41

Myth A fuel map from a similar engine will work.

Fact Breathing differs with cams, intake and exhaust, so maps are engine-specific and must be checked with a wideband.Medium42

Frequently asked

What is a fuel map?

A fuel map is the ECU table that sets fuel at each rpm and load point. It may store volumetric efficiency, pulse width or fuel mass, and the ECU combines it with a lambda target and corrections to calculate injector open time each cycle.Medium34

What is the difference between a VE table and a fuel map?

A VE table is one kind of fuel map. It stores how well the engine fills with air, and the ECU calculates fuel from it. Other fuel maps store pulse width directly, which mixes breathing and mixture together.Medium41

How do you tune a fuel map?

Set correct injector data and sensor calibrations, then log wideband lambda against target in steady states. Correct each cell by the ratio of measured to target lambda, smooth the table, and repeat until errors are small across the map.Medium65

What units are used in a fuel map?

Axes usually use rpm and kPa MAP, throttle percent or airflow. Cells hold percent VE, milliseconds of pulse width, or fuel mass in milligrams, depending on the ECU strategy. Check which your ECU uses before editing it.Medium31

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  3. Engine control unit · Wikipedia · reference · retrieved 2026-10-27
  4. Volumetric efficiency · Wikipedia · reference · retrieved 2026-10-27
  5. Injection Valve EV 14 data sheet · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  6. Lambda Sensor LSU 4.9 product page · Bosch Motorsport · vendor-doc · retrieved 2026-10-27
  7. Stoichiometry (air-to-fuel ratio of common fuels) · Wikipedia · reference · retrieved 2026-10-27