Rolling anti-lag

rolling ALSroll anti-lagrolling launch anti-lagrolling boost builder

Rolling anti-lag is an engine control mode that builds turbo boost while the car is moving at a steady, limited speed, so it can accelerate from a roll with boost already up. It typically retards ignition, cuts some ignition or fuel events and adds fuel so combustion heats the turbine.Medium346

How it works

Standard anti-lag keeps the turbo spinning off throttle.

A two-step limits rpm while stationary for launches. Rolling anti-lag applies similar tricks while moving, often for roll races or rally stages, holding a set rpm or speed until the driver releases the trigger.Medium43

It builds boost by retarding ignition heavily and enriching the mixture, so combustion continues as the gas leaves the cylinder and the energy reaches the turbine. Some systems also cut spark on selected cylinders, letting unburned charge ignite in the hot manifold.Medium342

Activation is usually a button or switch plus conditions: a speed window, throttle above a threshold and coolant temperature in range. Wikipedia notes some anti-lag systems shut off when coolant reaches about 110-115 °C (230-239 °F).Low36

The cost is heat. Late combustion pushes very hot gas through exhaust valves, the manifold and the turbine. Overuse can damage the turbine wheel and manifold, and unburned fuel burning in a catalyst can overheat and destroy it.Medium312

Typical values

ActivationDriver switch plus speed, throttle and temperature conditionsLow confidence36
Boost-building methodHeavy ignition retard, enrichment, selective spark or fuel cutSourced · medium34
Throttle bypass opening (ALS reference)About 12-20° of throttle openingSourced · medium3
Coolant cutoff (example)About 110-115 °C230-239 °FSourced · medium3
Typical useClosed-course roll racing, rally, time attackSourced · medium3

How an ECU uses it

The ECU enters rolling anti-lag only when every condition is true, then targets an rpm or vehicle speed using ignition retard and cut patterns rather than throttle alone. Leaving the mode on trigger release or any condition failing returns normal timing and fuel.Low361

A good strategy limits time in the mode, watches exhaust gas temperature and coolant, and exits on any sensor fault. Without these limits, a stuck switch can run the engine in a high-heat mode for far longer than the parts tolerate.Low31

How to test it

4 checks, in order.

  1. Verify all activation conditions on a stationary car with the engine off: switch input, speed signal, throttle and temperature. Confirm the ECU reports each condition correctly before enabling the mode.Low1
  2. On a closed course, enable the mode briefly and log rpm, boost, ignition angle, lambda and exhaust gas temperature. Keep sessions short and let temperatures recover between runs.Low31
  3. After each session, inspect the exhaust manifold, turbine and downpipe for cracks and discoloration, and watch for oil in the exhaust that suggests seal damage.Low34
  4. Safety
    use rolling anti-lag only on a closed course, with a fire extinguisher at hand and no flammable material near the exhaust. Afterfire and very hot exhaust parts can ignite grass, fuel vapor or debris.Medium34

Symptoms and causes

Turbine wheel or manifold cracking

Likely causes Extended time in anti-lag; very high exhaust temperatures.

Check Log time-in-mode and EGT; inspect for heat discoloration.

Medium3

Loss of catalyst efficiency or a glowing cat

Likely causes Unburned fuel burning in the catalyst.

Check Check catalyst temperature and emissions; look for a rattle from a broken substrate.

Low13

Mode will not engage

Likely causes One activation condition not met, such as speed or temperature.

Check Log each condition while pressing the switch.

Low6

In tuning

Treat rolling anti-lag as consumable heat.

Use the least retard and enrichment that builds the boost you need, and cap time in the mode. More aggressive settings build boost faster but shorten turbine, manifold and valve life.Low32

Pair the mode with exhaust gas temperature and coolant limits, a time limit and a fault exit. Engines and turbos that see anti-lag regularly need parts suited to the heat, and stock engines are generally not tuned for these loads.Medium43

Common mistakes

Mistake Running rolling anti-lag with a catalytic converter in place.

Do instead Unburned fuel can overheat and destroy the catalyst; this mode is for dedicated closed-course vehicles only.Low13

Mistake Holding the mode for long periods.

Do instead Limit time in mode and log exhaust temperature between runs.Medium3

Mistake Confusing rolling anti-lag with a two-step.

Do instead Two-step limits rpm at a standstill; rolling anti-lag builds boost while moving.Medium4

Safety, legal and emissions

Rolling anti-lag creates very hot exhaust parts and afterfire.

Use it only on closed courses, keep extinguishers nearby, and check that fuel, oil and brake lines are shielded from exhaust heat.Medium34

In the US, the Clean Air Act prohibits tampering with emissions controls on vehicles used on public roads, and EPA enforces against defeat devices. This is general information, not legal advice.5

Motorsport sanctioning bodies set their own rules on anti-lag use. Check the series regulations before enabling any anti-lag mode.Low3

Myths vs facts

Myth Rolling anti-lag is harmless if the flames look good.

Fact Visible flames mean combustion is happening outside the cylinder, which loads the turbine, manifold and valves with heat.Medium34

Myth Rolling anti-lag and two-step are the same thing.

Fact A two-step is a secondary rev limit for launching from rest. Rolling anti-lag holds boost while moving.Medium46

Frequently asked

What is rolling anti-lag?

Rolling anti-lag is a control mode that builds boost while the car is moving at a controlled speed, so it can accelerate from a roll with the turbo already spooled. It uses ignition retard, enrichment and sometimes spark cut to send combustion energy to the turbine.Medium34

Is rolling anti-lag bad for your turbo?

It adds heat and wear. Late combustion puts very hot gas through the turbine wheel and manifold, and overuse can damage them. Limiting time in mode, logging exhaust temperature and using heat-tolerant parts reduce, but do not remove, the extra wear.Medium32

What is the difference between rolling anti-lag and a 2-step?

A 2-step is a secondary rev limiter used at a standstill to launch with boost. Rolling anti-lag works while moving, holding speed or rpm until the driver releases the trigger. Both often use spark retard and cuts, but they target different situations.Medium46

Does rolling anti-lag damage the catalytic converter?

It can. Unburned fuel reaching a catalyst burns inside it and can overheat the substrate. That is one reason anti-lag belongs on dedicated competition vehicles. In the US, removing or disabling emissions controls on road vehicles is prohibited.Low15

Wiring, pinouts and parts

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Automotive Handbook, 10th edition (2018) · Robert Bosch GmbH / Wiley · book · retrieved 2026-10-27
  2. Internal Combustion Engine Fundamentals, 2nd edition (2018) · McGraw-Hill (John B. Heywood) · book · retrieved 2026-10-27
  3. Antilag system · Wikipedia · reference · retrieved 2026-10-27
  4. How does anti-lag work? · The Drive · press · retrieved 2026-10-27
  5. Tampering and Aftermarket Defeat Devices enforcement alert (December 2020) · U.S. Environmental Protection Agency · reference · retrieved 2026-10-27
  6. Launch control (automotive) · Wikipedia · reference · retrieved 2026-10-27