Mazda SkyActiv-G · 2015-

SkyActiv-G 1.5 / 2.0 (MX-5 ND) tuning guide

Researched sections show a citation and confidence for every fact.

At a glance

Years2015-
Displacement2L
LayoutI4
InductionNaturally aspirated
InjectionDirect injection
Cam controldual S-VT
IgnitionCoil-on-plug
Swap demandLow

Factory rating and volume

Power181hpat 7000 rpmSourced
Torque151lb-ftat 4000 rpmSourced
Redline7500rpm
Compression13.0:1
Estimated production220k–340kunitsCentral estimate 280k, low confidence. Sizes the tuning market; not a production figure.Estimate

Sourced Rating basis: Mazda USA 2019 MX-5 Miata features/specs sheet (2.0 PE-VPR, 2019+)

Factory fueling

How the factory ECU meters fuelReported
Load sensing
Not yet sourced
O2 sensor
Reported: wideband A/F (UEGO)
Closed loop
Not yet sourced
Year / market notes and sources

Mazda part named 'Sensor, Air&Fuel Ratio, front' for MX-5 Mk4 2015-17 (dealer listing). Skyactiv-G 2.0 MAF PE01-13-215 exists, but MX-5 fitment not confirmed.

  1. ilmotorsport.de/en/mx-5-sensorairfuel-rati-front-mk4-2015-2017-8487
  2. mazdashop.ca/en-mx/products/sensor-mass-air-flow-maf-mazda-pe01-13-215

Fuel injectors

Factory injector · DI injectionSourced · medium
Style
GDI (direct injection, solenoid)
Flow
Not yet sourced
Impedance
DI (high-voltage solenoid drive)
Feed
Not yet sourced
Connector
Not yet sourced
Size
Not yet sourced
Maker
Not yet sourced
Part numbers
Not yet sourced
Notes and sources

Direct injection only. No maker-listed direct-fit aftermarket DI injector found (ID Miata listings stop at 06-14).

  1. DI drop-ins for Mazda MZR DISI / SkyActiv-G · E-1312 · inferred

Direct-fit upgrades

No maker lists a direct-fit set for the SkyActiv-G 1.5 / 2.0 (MX-5 ND) yet.

Maker-listed fitment, not tested by GAINS. Check the connector, O-ring sizes and length against your engine before ordering. Size the injector with the injector size calculator and the pressure and flow calculator.

Key sensors

Factory sensors and OEM part numbers
Knock
MX-5 ND 2.0 (Autodoc)Reported
piezo knock sensor ×1Reported: PE01-18-921Cross-reference: NTY (listing)
Notes and sources

L807-18-921 also listed for 2020-25 MX-5

  1. sensors/Mazda SkyActiv-G knock MAF · E-1430
MAP / MAF
MAP
Reported
Part number not yet sourced
Notes and sources
  1. sensors/types inferred · E-1434 · inferred
MAF
Reported
hot-film ×1Reported: PE01-13-215
Notes and sources

ND fitment not confirmed

  1. sensors/Mazda SkyActiv-G knock MAF · E-1430
O2 (upstream)
Reported
wideband A/F sensor ×1Part number not yet sourced
Notes and sources

Not sourced

  1. sensors/types inferred · E-1434 · inferred
O2 (downstream)
Not yet sourced
Crank position
Not yet sourced
Cam position
Not yet sourced

Part numbers from OEM parts catalogues and maker listings. Several engines change sensors by year or market: match the years chip to your engine before ordering.

Internals and limits

Bottom end and head sealingReported
Block
aluminium
Liners
Not yet sourced
Main caps
Not yet sourced
Crankshaft
2019 update: crank revised (reports differ)
Connecting rods
2019: 41 g lighter rods (Hooniverse)
Pistons
2019: 27 g lighter pistons (Hooniverse)
Head fasteners
Not yet sourced
Sources
  1. en.wikipedia.org/wiki/Mazda_Skyactiv
  2. hooniverse.com/mazdas-2019-mx-5-delivers-a-greater-driving-experience/
  3. pistonheads.com/news/ph-japanesecars/new-bbr-mazda-mx-5-turbo-kit/36143

Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Modeled power and torque

SkyActiv-G 1.5 / 2.0 (MX-5 ND): stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
0501001502002503003500501001502002503001k2k3k4k5k6k7khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (181 hp at 7000 rpm, 151 lb-ft at 4000 rpm); the curve shape between peaks is modeled. Intake + exhaust + tune (pump fuel): Typical NA gains come mostly above mid-rpm.

How GAINS approaches the SkyActiv-G 1.5 / 2.0 (MX-5 ND)

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Cam phasing (VVT)gated

    Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.

  4. 4
    Direct injectionplanned

    Rail-pressure targets and injection phasing run on the DI driver. Dual-injection engines add a port / DI split, which starts from the factory's general strategy and is refined from logs.

  5. 5
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  6. 6
    Wideband sensorhardware

    the factory sensor is already an A/F type; for tuning, fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller (factory A/F sensors are not LSU-compatible)

  7. 7
    Bottom end and head sealingfactory reference

    Reported: 13:1 compression cited as a boost constraint (PistonHeads/BBR); no reputable bottom-end limit found. (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Plug-and-play harnesses for the SkyActiv-G 1.5 / 2.0 (MX-5 ND)

Harnesses built for the published S3 pinout that fit vehicles with this engine. Check the fitment line: most are specific to a chassis, market or transmission.

Plug-and-play

Being researched

We're mapping S3 plug-in and factory-connector adapter harnesses to this application.

Wire-in

Universal flying lead or re-terminated factory harness

Always available: terminate the engine side to ECU2's two Superseal 34 connectors. Universal harness from $405 USD list.

Go deeper

Valvetrain, triggers, factory engine management, timing considerations and weak points for every generation are on the Mazda SkyActiv-G guide.

Vehicles with the SkyActiv-G 1.5 / 2.0 (MX-5 ND)

GAINS on the SkyActiv-G 1.5 / 2.0 (MX-5 ND)

ECU2 + DI

ECU2Full sequential fuel and spark for this 4-cylinder, and its electronic throttle, with the wideband built in.Est. availability: April 2027
DIDrives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2 + DI; direct injection is handled by the DI driver. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.