Hyundai Lambda · 2010-12

Lambda 3.8 MPI specs: horsepower, injectors and sensors

The Lambda 3.8 MPI is a naturally aspirated 3.8 L V6 engine from Hyundai (2010-12) with port fuel injection and coil-on-plug ignition. The factory ECU measures load by MAF. Below: factory specification and ratings, sensor part numbers, OEM injectors and direct-fit upgrades, triggers, swaps and tuning notes, each with its evidence.Low1117910 Conflict

Power: 306 hp @ 6,300 rpm · Torque: 266 lb-ft (361 Nm) @ 4,700 rpm (Hyundai rating, not a GAINS measurement)Low1

Factory specification

Layout, dimensions and factory hardware, each with its source.

Production years2010-12Catalog range across the variants on this page.Researched, unverified
Displacement3.8L3,778 cc from bore × strokeConflict1
LayoutV6Researched, unverified
Bore × stroke96 × 87mm3.78 × 3.43 inConflict1
Aspirationnaturally aspiratedResearched, unverified
Fuel injectionport fuel injectionSourced · medium117910
Blockaluminiumalloy block and heads per Hyundai launch releaseLow confidence2

Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.

Lambda 3.8 MPI horsepower and torque

Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.

Power (Hyundai rating)306hp @ 6,300 rpm2010-12 Genesis Coupe 3.8 MPI US rating; Nm convertedConflict1
Torque (Hyundai rating)266 lb-ft @ 4,700 rpm361 NmConflict1
Other published ratings
ItemPowerTorque
Wikipedia303-316 PS @6400299-312 hp359 Nm @4600rpm conflict
3.8 GDI Genesis Coupe348 hp @6400353 PS400 Nm @5300, CR 11.5295 lb-ft
Conflict1

Lambda 3.8 MPI firing order

Lambda 3.8 MPI injectors

The factory injector, then direct-fit upgrades the makers list for this engine.

Factory injector

Styletop-feedmaker not confirmedSourced · medium117910
OEM part numbers35310-3C2002008/09-2011 MPISourced · medium117910
ImpedancehighsaturatedSourced · medium117910
LengthcompactSourced · medium117910
FeedtopSourced · medium117910
O-ring OD (top / bottom)14/ 14 mmSourced · medium117910

Direct-fit upgrades

Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.

InjectorFlowFit
DeatschWerks DW 600cc matched set · 35U-00-0600-614600 cc/min maker listing nominal (rating pressure not stated in listing)Check connector connector not stated on maker listing
DeatschWerks DW 800cc matched set · 35U-00-0800-615800 cc/min maker listing nominal (rating pressure not stated in listing)Check connector connector not stated on maker listing
Grams Performance Grams 750cc injector kit · G2-0750-1501Medium10750 cc/min at 3 bar (maker)Check connector maker sells plug-and-play jumpers separately; check connector
Grams Performance Grams 1000cc injector kit · G2-1000-1501Medium101000 cc/min at 3 bar (maker)Check connector maker sells plug-and-play jumpers separately; check connector
Injector Dynamics ID1050-XDS · 1050.34.14.14.6357121065 cc/min at 3.0 bar (43.5 psi), gasoline, 52 C (maker nominal)Check connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters
Injector Dynamics ID1750-XDS · 1750.34.14.14.64681728 cc/min at 3.0 bar (43.5 psi), E10 cert fuel, 49 C (maker nominal)Check connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters

Sensors

Factory sensors by role: part numbers, signal type and fitment years.

SensorOEM part numbersType / signalYears and markets
Crank position × 1Hyundai 39310-3C100 (replaces 39310-3C200)Sourced13crankshaft angle sensorMPI
Cam positionHyundai 39318-3C100 (replaces 39318-3C300)Sourced13camshaft position sensorGDI and MPI
Knock × 2 (LH, RH)Hyundai 39320-3C700 (LH) | 39320-3C600 (RH)Sourced13knock sensorGenesis Coupe 3.8 MPI 2010-12GDI 3.8 uses 39320-3C750/3C650
MAP × 1Hyundai 39300-3C500Sourced13MAP sensorGenesis Coupe 3.8 MPI/GDI
MAF × 1Hyundai 28164-3F100Sourced13air flow sensor assemblyGenesis Coupe 201128164-3C100 also listed for 3.8 by other sellers
O2 (upstream) × 2Hyundai 39210-3C820 | 39210-3C920Sourced13oxygen sensor (upper)Genesis Coupe 3.8 MPI
O2 (downstream) × 2Hyundai 39210-3C830Sourced · medium13oxygen sensorMPI and TCI/MPI (sold qty 2)

Ignition and triggers

Ignition systemcoil-on-plugResearched, unverified
Crank triggercrankshaft angle sensorMPISourced13
Cam sensorcamshaft position sensorGDI and MPISourced13
Valve timingdual CVVTResearched, unverified

Tuning notes

Factory load sensing

The factory ECU measures load by MAF (hot-wire / hot-film). Parts guide: MAF fitted on Genesis Coupe 3.8 V6 (2010-13). OEM docs not read. O2 not sourced. Researched, unverified

Injector drive

Factory injector impedance: high (saturated).Medium117910

Driver and calibration

High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified

Known limits (reported)

Forum opinion puts stock rods around 400 crank hp;Low2

Common first upgrades (reported)

Builders most often report upgrading: steel rods, forged pistons, sleeves, ARP head/main studs (Bisimoto SEMA build).Low2

Valvetrain, factory engine management and weak points across every generation are on the Hyundai Lambda guide.

Vehicles with the Lambda 3.8 MPI

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

15 sources
  1. Factory ratings: Hyundai Theta 2.0T / Lambda 3.8 (Genesis Coupe) (E-760) · kbb.com · press · retrieved 2026-10-25
  2. Hyundai Lambda 3.8 (E-1076) · wardsauto.com · press · retrieved 2026-10-25
  3. Injector aftermarket fitment (E-1200) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  4. Injector aftermarket fitment (E-1202) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  5. Injectors / ID1050-XDS fitment (E-1230) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  6. Injectors / ID1750-XDS fitment (E-1232) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  7. Injector Dynamics ID1050-XDS fitment table (E-1260) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  8. Injector Dynamics ID1300/ID1750/ID2600 fitment tables (E-1261) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  9. DeatschWerks catalogue (Shopify product feed) (E-1264) · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  10. Grams Performance catalogue (E-1266) · gramsperformance.com · reference · retrieved 2026-10-25
  11. Hyundai Genesis Coupe OEM injectors (E-1279) · hyundaipartsdeal.com · vendor-doc · retrieved 2026-10-25
  12. Injector Dynamics ID1050-XDS fitment table (E-1290) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  13. Part numbers (E-1394) · hyundaipartsdeal.com · vendor-doc · retrieved 2026-10-25
  14. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  15. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25

Evidence ids (E-…) refer to our research register; each records the source, date and confidence.