Nissan KA24 · 1991-04

KA24DE horsepower: specs, injectors and sensors

The KA24DE is a naturally aspirated 2.4 L inline-4 engine from Nissan (1991-04) with port fuel injection and distributor ignition. The factory ECU measures load by MAF. Below: factory specification and ratings, sensor part numbers, OEM injectors and direct-fit upgrades, triggers, swaps and tuning notes, each with its evidence.Low1324

Power: 155 hp @ 5,600 rpm · Torque: 160 lb-ft (217 Nm) @ 4,400 rpm (Nissan rating, not a GAINS measurement)Medium13

Factory specification

Layout, dimensions and factory hardware, each with its source.

Production years1991-04Catalog range across the variants on this page.Researched, unverified
Displacement2.4L2,389 cc from bore × strokeSourced · medium13
Layoutinline-4Researched, unverified
Bore × stroke89 × 96mm3.50 × 3.78 inSourced · medium13
Compression ratio9.5:1Sourced · medium13
Aspirationnaturally aspiratedResearched, unverified
Fuel injectionport fuel injectionLow confidence4
Blockcast ironSourced · medium13
Cylinder linersnoneiron blockSourced · medium13
Main caps
  • Girdled main bearings on Japanese block
  • Individual caps on Mexican block (Wikipedia)
Sourced · medium13

Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.

KA24DE horsepower and torque

Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.

Power (Nissan rating)155hp @ 5,600 rpmSAE net, US 1991-98 240SX KA24DE (Wikipedia/spec listings; no OEM document seen)Sourced · medium13
Torque (Nissan rating)160 lb-ft @ 4,400 rpm217 NmSourced · medium13
Other published ratings
  • D22 Navara/Frontier: 148 hp @5600, 153 lb-ft @3600, CR 9.2110 kW · 208 Nm
  • Xterra: 143 hp @5200, 154 lb-ft @4000, CR 9.2209 Nm
  • One low-quality source gives 240SX torque @4800
Sourced · medium13

KA24DE firing order

KA24DE injectors

The factory injector, then direct-fit upgrades the makers list for this engine.

Factory injector

StyleNissan/JECS side-feed240SX 91-98Low confidence4
MakerJECSLow confidence4
ImpedancehighsaturatedLow confidence4
ConnectorJECS Nissan side-feedLow confidence4
LengthotherLow confidence4
FeedsideLow confidence4

Direct-fit upgrades

Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.

InjectorFlowFit
DeatschWerks 270cc - G20/SR20/240sx SR20DET/KA24DE (side feed, 91-98) · 01J-00-0270-47270 cc/min maker listing (pressure basis not stated on product page)Plug-in
DeatschWerks 370cc - G20/SR20/240sx SR20DET/KA24DE (side feed, 91-98) · 01J-00-0370-410370 cc/min maker listing (pressure basis not stated on product page)Plug-in
DeatschWerks 550cc - G20/SR20/240sx SR20DET/KA24DE (side feed, 91-98) · 01J-00-0550-49550 cc/min maker listing (pressure basis not stated on product page)Plug-in
DeatschWerks 950cc - G20/SR20/240sx SR20DET/KA24DE (side feed, 91-98) · 02J-01-0950-48950 cc/min maker listing (pressure basis not stated on product page)Plug-in

Sensors

Factory sensors by role: part numbers, signal type and fitment years.

SensorOEM part numbersType / signalYears and markets
Crank position × 1Not yet sourcedResearched, unverifiedoptical CAS (in distributor on 240SX) · digital (optical)Part number not sourced
Knock × 122060-30P00|alt 24079-31U01 (listing)Low confidence5piezo knock sensor1991-98 240SXSeller listings
MAPNot yet sourcedResearched, unverifiedNot yet sourcedMAF-based
MAF × 122680-53F00Low confidence6hot-wire, analog 0-5 V · 0-5 V analog240SX/Stanza/Sentra (listing)
O2 (upstream) × 1Not yet sourcedResearched, unverifiednarrowband zirconia · 0-1 V

Ignition and triggers

Ignition systemdistributorResearched, unverified
Crank triggeroptical CAS (in distributor on 240SX), digital (optical)Researched, unverified
Valve timingnoneResearched, unverified

Tuning notes

Factory load sensing

The factory ECU measures load by MAF (hot-wire / hot-film). 1991-94 S13 FSM: MAF hot film, single oxygen sensor (pre-OBD-II, no rear). 1997 S14 FSM: MAF hot wire, front + rear heated O2 (OBD-II 1996+).2

Factory oxygen sensors

Upstream: narrowband (zirconia) (1). Downstream O2 sensors: varies. Closed-loop fuelling: narrowband closed loop at stoich; open loop decel/accel, high load/high speed, cold/failed sensor (Nissan FSM).2

Injector drive

Factory injector impedance: high (saturated). Connector: JECS Nissan side-feed.Low4

Driver and calibration

High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified

Common first upgrades (reported)

Builders most often report upgrading: forged rods and pistons, ARP head/main studs, MLS head gasket, shim-under-bucket followers (DSPORT build).Medium13

Valvetrain, factory engine management and weak points across every generation are on the Nissan KA24 guide.

Vehicles with the KA24DE

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

10 sources
  1. Factory ratings: Nissan KA family (KA24DE) (E-735) · en.wikipedia.org · reference · retrieved 2026-10-25
  2. Nissan SR/KA ECCS fueling (E-840) · servicemanuals-backend.fly.storage.tigris.dev · service-manual · retrieved 2026-10-25
  3. Nissan KA24DE internals (E-1095) · en.wikipedia.org · reference · retrieved 2026-10-25
  4. DeatschWerks injector catalogue (E-1294) · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  5. Sensors/Nissan knock 22060-30P00 and SR CAS (E-1418) · walmart.com · reference · retrieved 2026-10-25
  6. Sensors/Nissan KA24 MAF (E-1419) · ebay.de · vendor-doc · retrieved 2026-10-25
  7. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  8. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  9. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  10. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25

Evidence ids (E-…) refer to our research register; each records the source, date and confidence.