Engine: KA24DE
Part of the Nissan KA24 family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (155 hp at 5600 rpm, 160 lb-ft at 4400 rpm); the curve shape between peaks is modeled. Intake + exhaust + tune (pump fuel): Typical NA gains come mostly above mid-rpm.
KA24DE data
- Load sensing
- MAF (hot-wire / hot-film)
- O2 sensor
- narrowband (zirconia)
- Closed loop
- narrowband closed loop at stoich; open loop decel/accel, high load/high speed, cold/failed sensor (Nissan FSM)
- Block
- cast iron
- Rods / pistons
- oil squirters in both blocks (Wikipedia); factory pistons crack at ring lands past ~300 hp (DSPORT)
- Reported limit
- ~300 hp on stock internals with proper tuning (DSPORT)
- Factory
- Nissan/JECS side-feed (240SX 91-98)
- Impedance
- high (saturated)
- Direct-fit upgrades
- 4 maker-listed
- Knock
- 22060-30P00|alt 24079-31U01 (listing)
- MAP / MAF
- 22680-53F00
- O2 (upstream)
- narrowband zirconia
Platform background
The S13 platform was sold as the Silvia and 180SX in Japan (CA18DET, then SR20DE/SR20DET from the January 1991 minor change) and as the 240SX in North America with the KA24. The SR20DET swap into US 240SX cars is the most common S13 build. This page gives the factory ECM terminal table for the 1991-94 US 240SX KA24DE from Nissan's service manual, which is the chassis-side reference for swap wiring.
Factory ECU
Nissan ECCS, MAF-based, with the crank angle sensor in the distributor (reference and 1 degree position signals, 0-5 V digital)
Sourced1- Malfunction indicator lamp on all models
- Separate California and non-California calibrations
Swap wiring on a US S13 usually merges a JDM SR20DET engine harness and ECU with the 240SX body harness, or replaces both with a standalone. Signals that must be carried across include ECM power and ignition feeds, fuel pump relay control, tachometer, coolant gauge sender, A/C request and neutral switch. The JDM SR20DET ECU terminal table was not obtained in English; verify against the Japanese Nissan manual or the SR20DET harness itself.
Factory ECU: harness cross-reference
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Nissan ECCS, S13 240SX KA24E/KA24DE
- Applies to
- 1989-1994 240SX (S13), manual; USDM
- Not for
- automatic (A/T and M/T ECUs differ)
23710-40F00 (1989), 40F01 (1989-90), 40F07 (1990-91) are KA24E examples from dealer catalogue; 1991-94 KA24DE numbers not found. One harness spans KA24E (SOHC) and KA24DE (DOHC) ECU versions. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
- ECU family
- Nissan ECCS, S14 240SX KA24DE (OBD-II from 1996)
- Applies to
- 1995-1998 240SX (S14), manual; USDM
- Not for
- automatic; 1995 OBD1 cars use BF29154-S3 per Boomslang SKU split
23710-72F13 listed for 1996-97 240SX KA24DE (superseded 2371M-72F15RE reman); example only. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
- ECU family
- Nissan ECCS, S14 240SX KA24DE (OBD-I)
- Applies to
- 1995 240SX, manual; USDM
- Not for
- 1996-98 OBD-II
No 1995-specific number found. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
Factory ECU pinout
Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.
Nissan 240SX (S13) KA24DE ECM, 1991-94 US
The Nissan 240SX (S13) KA24DE ECM, 1991-94 US uses 1 connector with 64 cavities. This page draws each face from the OEM figure and lists the 34 terminals the OEM table documents, with wire colours where the manual prints them.
1991-1994 · US · 1 connector, 64 cavities · 34 terminals sourced
Looking into the harness plug's mating face (mirror of the ECU face).
How the OEM figure is oriented
Harness side (looking into the plug), as drawn in the OEM figure.| Pin | Function | Type | Wire | Notes |
|---|---|---|---|---|
| 1 | Ignition signal | Ignition | — | |
| 3 | Ignition check | Ignition | — | |
| 4 | ECCS relay (self-shutoff) | Outputs | — | |
| 8 | EGR temperature sensor | Sensor signal | — | |
| 9 | Condenser fan relay | Outputs | — | |
| 11 | Air conditioner relay | Outputs | — | |
| 16 | Mass air flow sensor | Sensor signal | — | |
| 18 | Engine coolant temperature sensor | Sensor signal | — | |
| 19 | Oxygen sensor | Sensor signal | — | |
| 20 | Throttle position sensor | Sensor signal | — | |
| 22 | Crank angle sensor reference signal | Crank / cam | — | |
| 25 | S.C.V. (swirl control valve) control solenoid | Outputs | — | |
| 27 | Knock sensor | Sensor signal | — | |
| 30 | Crank angle sensor reference signal | Crank / cam | — | |
| 31 | Crank angle sensor position signal | Crank / cam | — | |
| 34 | Start signal | Sensor signal | — | |
| 35 | Neutral position switch | Sensor signal | — | |
| 36 | Ignition switch | Power | — | |
| 37 | Throttle position sensor power supply | Sensor 5 V / ground | — | |
| 38 | Power supply for ECM | Power | — | |
| 40 | Crank angle sensor position signal | Crank / cam | — | |
| 41 | Air conditioner switch | Sensor signal | — | |
| 43 | Power steering oil pressure switch | Sensor signal | — | |
| 45 | Fan switch | Sensor signal | — | |
| 46 | Power supply (back-up) | Power | — | |
| 47 | Power supply for ECM | Power | — | |
| 101 | Injector No. 1 | Injector | — | |
| 102 | PAIRC solenoid valve | Outputs | — | |
| 103 | Injector No. 3 | Injector | — | |
| 104 | Fuel pump relay | Outputs | — | |
| 105 | EGR and canister control solenoid valve | Outputs | — | |
| 110 | Injector No. 2 | Injector | — | |
| 112 | Injector No. 4 | Injector | — | |
| 113 | IACV-AAC valve | Outputs | — |
Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.
Coverage, year splits and safety
Covers the US-market 240SX KA24DE ECM only (1991-94). The catalog row also spans the S14; the 1997 S14 KA24DE ECM is its own family. The JDM S13 SR20DET ECU is a different unit and is not covered.
Source notes: This table is the US 240SX KA24DE ECM from the Nissan 240SX service manual (EF and EC section, ECM inspection table); it is not the SR20DET ECU. Grounds and wire colours are not listed in that table. The JDM S13 Silvia/180SX SR20DET ECCS terminal table is in the Japanese-language Nissan RPS13/PS13 service manual (Section B1/EC), which was not parsed.
Safety: disconnect the battery before working on the ECU harness, and confirm each terminal with a meter against your own car's manual before cutting or pinning wires.
Nissan 240SX (S14) KA24DE ECM, 1997 US
The Nissan 240SX (S14) KA24DE ECM, 1997 US uses 1 connector with 88 cavities. This page draws each face from the OEM figure and lists the 74 terminals the OEM table documents, with wire colours where the manual prints them.
1997 · US · 1 connector, 88 cavities · 74 terminals sourced
Looking into the harness plug's mating face (mirror of the ECU face).
How the OEM figure is oriented
Harness side (looking into the plug), as drawn in the OEM figure.| Pin | Function | Type | Wire | Notes |
|---|---|---|---|---|
| 1 | Ignition signal | Ignition | W | |
| 2 | Ignition check | Ignition | Y/R | |
| 3 | Tachometer | Comms / diag | Y/R | |
| 4 | ECCS relay (self-shutoff) | Outputs | R/B | |
| 5 | EVAP canister purge volume control valve | Outputs | L | |
| 6 | EVAP canister purge volume control valve | Outputs | Y/L | |
| 7 | 5th position switch (M/T) | Sensor signal | Y/L | A/T: A/T check signal (wire R/B). |
| 8 | Fuel pump relay | Outputs | B/P | |
| 9 | Air conditioner triple-pressure switch | Sensor signal | OR/B | |
| 10 | ECCS ground | Ground | B | |
| 13 | Cooling fan relay (high) | Outputs | OR/L | |
| 14 | Cooling fan relay (low) | Outputs | L/G | |
| 15 | Air conditioner relay | Outputs | B/P | |
| 16 | EVAP canister purge volume control valve | Outputs | W/B | |
| 17 | EVAP canister purge volume control valve | Outputs | R/G | |
| 18 | Malfunction indicator lamp | Comms / diag | OR | |
| 19 | ECCS ground | Ground | B | |
| 20 | Start signal | Sensor signal | OR | |
| 21 | Air conditioner switch | Sensor signal | OR/L | |
| 22 | Neutral position switch (M/T) | Sensor signal | G/OR | A/T: Inhibitor switch (wire R/G). |
| 23 | Throttle position sensor | Sensor signal | W | |
| 24 | A/T signal No. 1 | Sensor signal | L/G | |
| 25 | Power steering oil pressure switch | Sensor signal | PU/W | |
| 26 | Vehicle speed sensor | Sensor signal | Y/G | |
| 27 | Throttle position switch (closed position) | Sensor signal | L/G | |
| 28 | Intake air temperature sensor | Sensor signal | L/W | |
| 29 | A/T signal No. 2 | Sensor signal | L/W | |
| 30 | A/T signal No. 3 | Sensor signal | L/R | |
| 33 | Throttle position sensor signal to A/T control unit | Sensor signal | R/Y | |
| 37 | Ambient air temperature switch | Sensor signal | L/W | |
| 38 | Ignition switch | Power | B/R | |
| 39 | ECCS ground | Ground | B | |
| 40 | Camshaft position sensor (reference signal) | Crank / cam | W | |
| 41 | Camshaft position sensor (position signal) | Crank / cam | B | |
| 43 | ECCS ground (measurement reference) | Ground | B | |
| 44 | Camshaft position sensor (reference signal) | Crank / cam | W | |
| 46 | Front heated oxygen sensor | Sensor signal | W | |
| 47 | Mass air flow sensor | Sensor signal | W | |
| 48 | Mass air flow sensor ground | Sensor 5 V / ground | B | |
| 49 | Sensors' power supply | Sensor 5 V / ground | LG/R | |
| 50 | Sensors' ground | Sensor 5 V / ground | B | |
| 51 | Engine coolant temperature sensor | Sensor signal | L/OR | |
| 52 | Rear heated oxygen sensor | Sensor signal | W | |
| 53 | Crankshaft position sensor (OBD) | Crank / cam | P | |
| 54 | Knock sensor | Sensor signal | W | |
| 55 | Rear window defogger relay | Outputs | L/R | |
| 56 | Power supply for ECM | Power | B/W | |
| 58 | Data link connector for GST | Comms / diag | R | |
| 61 | Power supply for ECM | Power | B/W | |
| 62 | EGR temperature sensor | Sensor signal | B/W | |
| 63 | Tank fuel temperature sensor | Sensor signal | Y | |
| 64 | Data link connector for CONSULT | Comms / diag | G/B | |
| 65 | Data link connector for CONSULT | Comms / diag | G | |
| 66 | Absolute pressure sensor | Sensor signal | W | |
| 67 | EVAP control system pressure sensor | Sensor signal | G | |
| 68 | Data link connector for CONSULT | Comms / diag | G/W | |
| 69 | MAP/BARO switch solenoid valve | Outputs | Y/B | |
| 70 | Power supply (back-up) | Power | R | |
| 101 | IACV-AAC valve (open) | Outputs | BR | |
| 102 | Injector No. 1 | Injector | W/B | |
| 103 | EGRC-solenoid valve | Outputs | L/R | |
| 104 | Injector No. 3 | Injector | G/B | |
| 105 | EVAP canister purge control solenoid valve | Outputs | Y/R | |
| 106 | ECCS ground | Ground | B | |
| 107 | Injector No. 2 | Injector | Y/B | |
| 108 | EVAP canister vent control valve | Outputs | Y/G | |
| 109 | Injector No. 4 | Injector | L/B | |
| 110 | Rear heated oxygen sensor heater | Outputs | B | |
| 112 | ECCS ground | Ground | B | |
| 113 | Current return | Other / not used | R | |
| 114 | REC relay | Outputs | OR/L | |
| 115 | Front heated oxygen sensor heater | Outputs | L | |
| 117 | Vacuum cut valve bypass valve | Outputs | G/R | |
| 118 | ECCS ground | Ground | B |
Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (medium confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.
Coverage, year splits and safety
Covers the 1997 US 240SX (S14) KA24DE ECM, from the 1997 service manual. 1995-96 and 1998 cars were not checked against their own manuals.
Source notes: SR20DET rows come from the Nissan Model S14 Series Service Manual (1994, LHD export) ECM input/output signal inspection table; the scanned copy is missing page EC-197 (terminals 1-18 including ignition and injector-to-cylinder assignment), so those rows are absent and must be taken from a complete copy of the manual or the S14 wiring diagram. KA24DE rows (with terminal-side wire colours) come from the 1997 Nissan 240SX service manual EC section, ECM inspection table.
Safety: disconnect the battery before working on the ECU harness, and confirm each terminal with a meter against your own car's manual before cutting or pinning wires.
Plug-and-play harness
No Haltech S3 plug-in harness is listed for this vehicle, but a Boomslang adapter harness is: it plugs into the factory ECU connector on one side and the S3 pinout on the other, so the ECU2 replaces the factory ECU without cutting the loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
![]() | Manual 1989 - 1994 Nissan 240SXBF29030-S3 | 1989-1994 240SX (S13), manual; USDM | $840Lowest | Maker ↗ |
![]() | Manual 1995 - 1998 Nissan 240SXBF29031-S3 | 1995-1998 240SX (S14), manual; USDM | $840Lowest | Maker ↗ |
![]() | Manual 1995 - 1995 Nissan 240SX OBD1BF29154-S3 | 1995 240SX, manual; USDM | $840Lowest | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1989 - 1994 Nissan 240SX
- Plugs into
ECCS ECU (KA24E 1989-90 / KA24DE 1991-94 240SX, S13) · 23710-40F00, 23710-40F01…
- OEM part numbers
- 23710-40F00, 23710-40F01, 23710-40F07
- ECU
- Nissan ECCS, S13 240SX KA24E/KA24DE
- Confidence
- medium
23710-40F00 (1989), 40F01 (1989-90), 40F07 (1990-91) are KA24E examples from dealer catalogue; 1991-94 KA24DE numbers not found. One harness spans KA24E (SOHC) and KA24DE (DOHC) ECU versions. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
- Fits
- 1989-1994 240SX (S13), manual; USDM
- Exclusions
- automatic (A/T and M/T ECUs differ)
- SKU
- BF29030-S3
- Maker fitment
- Nissan 240SX (Manual); selector years 1989-1994; SKU label: Manual 1989 - 1994 Nissan 240SX
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); S13 1989-94 (KA24E 89-90 incl.)

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1995 - 1998 Nissan 240SX
- Plugs into
ECM (KA24DE 1995-98 240SX, S14) · 23710-72F13
- OEM part numbers
- 23710-72F13
- ECU
- Nissan ECCS, S14 240SX KA24DE (OBD-II from 1996)
- Confidence
- medium
23710-72F13 listed for 1996-97 240SX KA24DE (superseded 2371M-72F15RE reman); example only. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
Sources: E-1481
- Fits
- 1995-1998 240SX (S14), manual; USDM
- Exclusions
- automatic; 1995 OBD1 cars use BF29154-S3 per Boomslang SKU split
- SKU
- BF29031-S3
- Maker fitment
- Nissan 240SX (Manual); selector years 1995-1998; SKU label: Manual 1995 - 1998 Nissan 240SX
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); S14 1995-98

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1995 - 1995 Nissan 240SX OBD1
- Plugs into
ECCS ECU (KA24DE, 1995 240SX, OBD-I)
- ECU
- Nissan ECCS, S14 240SX KA24DE (OBD-I)
- Confidence
- low
No 1995-specific number found. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
- Fits
- 1995 240SX, manual; USDM
- Exclusions
- 1996-98 OBD-II
- SKU
- BF29154-S3
- Maker fitment
- Nissan 240SX OBD1 (Manual); selector years 1995-1995; SKU label: Manual 1995 - 1995 Nissan 240SX OBD1
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 1995 OBD1 variant
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the 240SX S13 / S14
Planned with the same rules as the configurator for this car's 4 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.
- Price TBA
ECU2Engine controller
4 cyl · port injection · cable throttle
Runs this 4-cylinder's injectors and its distributor on one ignition output, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harnessNone listed for this car
- Factory-connector → S3 adapter3 listed · from $840 USD listBF29030-S3
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
Swap guides
Into the 240SX S13 / S14
How GAINS approaches the 240SX S13 / S14
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 4Factory load sensingfactory reference
What the factory ECU measures load with: MAF (hot-wire / hot-film) (high confidence)
- 5Wideband sensorhardware
Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller
- 6Bottom end and head sealingfactory reference
Reported: Per DSPORT, factory piston ring lands crack beyond ~300 hp especially with detonation; composite head gasket and shim followers at high rpm also cited. (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
Drivetrain
Chassis integration
When a JDM SR20DET ECU replaces the KA24DE ECM, chassis features controlled by the US ECM (condenser fan, A/C cut, power steering idle-up, emissions solenoids) must be reconnected to the corresponding SR ECU pins or recreated in a standalone.
Tuning notes
S13-era SR20DETs are tuned the same way as later versions: boost control, fuel, MAF or MAP load sensing and ignition developed with knock monitoring. Early S13 SR20DETs do not have the variable valve timing of the S14 and S15 engines, so VTC settings do not apply.
Popular swaps
Because the Silvia, 180SX and 240SX share the S13 body, SR20DET mounts, gearbox and driveshaft from a JDM car fit the US chassis. The main work is harness merging, fuel pump capacity and gauge integration. RB-series six-cylinder swaps are also common but require more fabrication.
GAINS on the 240SX S13 / S14
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Frequently asked
When did the S13 Silvia get the SR20DET?
In the January 1991 minor change, replacing the CA18DET.2
What are the US S13 KA24DE crank angle sensor pins?
Reference signal on terminals 22 and 30, position signal on 31 and 40.1
Which S13 KA24DE ECM pins are the injectors?
101 (No.1), 110 (No.2), 103 (No.3), 112 (No.4).1
Is there an official SR20DET pinout for the S13?
Nissan's English 240SX manual covers only the KA24DE; the SR20DET pinout is in the Japanese S13 manual.1
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- Nissan 240SX (S13, KA24DE, 1991-94) Service Manual, section EF and EC · Nissan North America (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
- Nissan Heritage Collection: Silvia K's (1989, S13) · Nissan Motor Co., Ltd. · oem · retrieved 2026-10-25
- Nissan Model S14 Series Service Manual (1994, LHD export, SR20DET), sections EM and EC · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)
- E-1480 harness ECU xref: Nissan 240SX 1989-91 KA24E (verified, high confidence)
- E-1490 harness ECU xref: Nissan S13/S14 SR20DET (unverified, low confidence)
- E-1481 harness ECU xref: Nissan 240SX 1996-97 KA24DE (verified, medium confidence)


