GM High Feature V6 (Alloytec) · 2004-09

LY7 3.6 V6 (Holden Alloytec, port injection) tuning guide

Researched sections show a citation and confidence for every fact.

At a glance

Years2004-09
Displacement3.6L
LayoutV6
InductionNaturally aspirated
InjectionPort injection
Cam controldual cam phasersintake; exhaust on some
IgnitionCoil-on-plug
Swap demandLow

Built at Port Melbourne; SIDI LLT/LFX successors not staged

Factory rating and volume

Power235hpat 6000 rpmLow confidence
Torque236lb-ftat 2800 rpmLow confidence
Compression10.2:1
Estimated production1.0M–3.5MunitsCentral estimate 2.0M, low confidence. Sizes the tuning market; not a production figure.Estimate

Low confidence Rating basis: Holden VZ 2004-05 (LW2 dual-fuel listing) 175 kW

Factory fueling

How the factory ECU meters fuelReported
Load sensing
Not yet sourced
O2 sensor
Not yet sourced
Closed loop
Not yet sourced
Year / market notes and sources

Sequential multi-port injection; load strategy and O2 layout not yet sourced.

  1. en.wikipedia.org/wiki/GM_High_Feature_engine

Fuel injectors

Factory injector · port injectionReported
Style
Not yet sourced
Flow
Not yet sourced
Impedance
Not yet sourced
Feed
Not yet sourced
Connector
Not yet sourced
Size
Not yet sourced
Maker
Not yet sourced
Part numbers
Not yet sourced
Notes and sources

Sequential multi-port; OEM injector data not yet sourced.

  1. GM High Feature V6 LY7 (Holden Alloytec) · E-16502

Direct-fit upgrades

No maker lists a direct-fit set for the LY7 3.6 V6 (Holden Alloytec, port injection) yet.

Maker-listed fitment, not tested by GAINS. Check the connector, O-ring sizes and length against your engine before ordering. Size the injector with the injector size calculator and the pressure and flow calculator.

Key sensors

Factory sensors and OEM part numbers
Knock
Not yet sourced
MAP / MAF
Not yet sourced
O2 (upstream)
Not yet sourced
O2 (downstream)
Not yet sourced
Crank position
Not yet sourced
Cam position
Not yet sourced

Part numbers from OEM parts catalogues and maker listings. Several engines change sensors by year or market: match the years chip to your engine before ordering.

Internals and limits

Bottom end and head sealingReported
Block
Not yet sourced
Liners
Not yet sourced
Main caps
Not yet sourced
Crankshaft
Not yet sourced
Connecting rods
Not yet sourced
Pistons
Not yet sourced
Head fasteners
Not yet sourced
Sources
  1. en.wikipedia.org/wiki/GM_High_Feature_engine

Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Modeled power and torque

Dyno model not available yet for the LY7 3.6 V6 (Holden Alloytec, port injection). Stock-anchored curves are added as factory ratings are sourced.

How GAINS approaches the LY7 3.6 V6 (Holden Alloytec, port injection)

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Cam phasing (VVT)gated

    Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.

  4. 4
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  5. 5
    Wideband sensorhardware

    factory O2 type not yet sourced; plan on a Bosch LSU 4.9 for the GAINS ECU's built-in controller

Plug-and-play harnesses for the LY7 3.6 V6 (Holden Alloytec, port injection)

Harnesses built for the published S3 pinout that fit vehicles with this engine. Check the fitment line: most are specific to a chassis, market or transmission.

Plug-and-play

Being researched

We're mapping S3 plug-in and factory-connector adapter harnesses to this application.

Wire-in

Universal flying lead or re-terminated factory harness

Always available: terminate the engine side to ECU2's two Superseal 34 connectors. Universal harness from $405 USD list.

Go deeper

Valvetrain, triggers, factory engine management, timing considerations and weak points for every generation are on the GM High Feature V6 (Alloytec) guide.

Vehicles with the LY7 3.6 V6 (Holden Alloytec, port injection)

GAINS on the LY7 3.6 V6 (Holden Alloytec, port injection)

ECU2

ECU2Full sequential fuel and spark for this 6-cylinder, and its electronic throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.