Factory specification
Layout, dimensions and factory hardware, each with its source.
Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.
M52 horsepower and torque
Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.
- M50B25: 192 PS @5900-6000, 245-250 Nm @4200-4700, 84 x 75 mm, 10.0 (TU 10.5)
- M52B25: 170 PS @5500, 245 Nm @3950
- S50B30 (Euro E36 M3): 286 PS @7000, 329 Nm @3500, 86 x 85.8 mm, 10.8
- S50B30US: 240 hp @6000, 225 lb-ft @4250
- S52B32 (US M3 1996-99): 240 hp @6000, 236-240 lb-ft @3800, 86.4 x 89.6, 10.5, redline 7000320-325 Nm
M52 firing order
M52 injectors
The factory injector, then direct-fit upgrades the makers list for this engine.
Factory injector
Direct-fit upgrades
Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.
| Injector | Flow | Fit |
|---|---|---|
| DeatschWerks DW 440cc matched set · 18U-09-0440-630 | 440 cc/min maker listing nominal (rating pressure not stated in listing) | Check connector connector not stated on maker listing |
| DeatschWerks DW 650cc matched set · 18U-09-0650-628 | 650 cc/min maker listing nominal (rating pressure not stated in listing) | Check connector connector not stated on maker listing |
| DeatschWerks DW 900cc matched set · 18U-09-0900-626 | 900 cc/min maker listing nominal (rating pressure not stated in listing) | Check connector connector not stated on maker listing |
| Fuel Injector Clinic FIC 650cc High-Z set · IS802-0650H25 | 650 cc/min at 43.5 psi (3 bar), 90 F, calibration fluid (maker) | Needs adapter PADPUtoJ6 (USCAR to Jetronic/EV1) or solder pigtails |
| Fuel Injector Clinic FIC 1000cc High-Z set · IS802-1000H29 | 1000 cc/min at 43.5 psi (3 bar), 90 F, calibration fluid (maker) | Needs adapter PADPUtoJ6 (USCAR to Jetronic/EV1) or solder pigtails |
| Fuel Injector Clinic FIC 1440cc High-Z set · IS802-1440H27 | 1440 cc/min at 43.5 psi (3 bar), 90 F, calibration fluid (maker) | Needs adapter PADPUtoJ6 (USCAR to Jetronic/EV1) or solder pigtails |
| Grams Performance Grams 750cc injector kit · G2-0750-1401Medium18 | 750 cc/min at 3 bar (maker) | Check connector maker sells plug-and-play jumpers separately; check connector |
| Grams Performance Grams 1000cc injector kit · G2-1000-1401Medium18 | 1000 cc/min at 3 bar (maker) | Check connector maker sells plug-and-play jumpers separately; check connector |
| Grams Performance Grams 1600cc injector kit · G2-1600-1401Medium18 | 1600 cc/min at 3 bar (maker) | Check connector maker sells plug-and-play jumpers separately; check connector |
| Injector Dynamics ID2600-XDS · 2600.60.14.14.69131522 | not stated maker page does not state a single nominal figure in extracted text; ~2600 class | Check connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters |
| Injector Dynamics ID1050-XDS · 1050.60.14.14.66101420 | 1065 cc/min at 3.0 bar (43.5 psi), gasoline, 52 C (maker nominal) | Check connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters |
| Injector Dynamics ID1300-XDS · 1300.60.14.14.67111521 | 1335 cc/min at 3.0 bar (43.5 psi), iso-octane, 52 C (maker nominal) | Check connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters |
| Injector Dynamics ID1750-XDS · 1750.60.14.14.681215 | 1728 cc/min at 3.0 bar (43.5 psi), E10 cert fuel, 49 C (maker nominal) | Check connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters |
Sensors
Factory sensors by role: part numbers, signal type and fitment years.
| Sensor | OEM part numbers | Type / signal | Years and markets |
|---|---|---|---|
| Crank position × 1 | BMW 12141726065 (M50 era: 325i/525i/M3, Hella)Cross-ref: Hella 12141726065Sourced2324 | Hall effect (3-wire) · impulse wheel with gap · digital square wave | M52 Hall per MS41 docRear of block, left side |
| Cam position × 1-2 | BMW 12141703221 (M52/S52: 323i/328i/528i/M3/Z3) | 12141726548 / 12141740383 (M50/S50)Cross-ref: Hella / Delphi / VemoSourced · medium2324 | Hall effect (cylinder ID) · digital | |
| Knock × 2 (cyl 1-3, 4-6) | BMW 12141703276 (M52/S52 US: 323i/328i/528i/M3/Z3) | 12141738667 (M50/S50: 325i/525i/M3)Cross-ref: Vemo 12141703276Sourced2324 | piezo (conductor-sound microphone) · AC voltage | M52 1995-00; M50 1990-95Count from BMW MS41 training (M52); M50 count not documented here |
| MAF × 1 | Not yet sourcedSourced23 | hot-film air mass meter (HFM) · 1-5 V signal · 0-5 V analog | M52 (MS41.1/41.2)Earlier M50 Motronic system not covered |
| O2 (upstream) × 2 (1 on 323i/Z3) | Not yet sourcedSourced · medium23 | narrowband zirconia heated (Siemens, resistive type) | M52 US (MS41)Training doc: pre-cat Siemens sensors vary in resistance |
| O2 (downstream) | Not yet sourcedSourced · medium23 | narrowband zirconia heated | M52 US OBD IIMS41 has pre and post cat sensors |
| Coolant temp × 1 | Not yet sourcedSourced23 | NTC thermistor · 0-5 V analog | Substitute value 80 C on fault |
| Intake air temp × 1 | Not yet sourcedSourced23 | NTC thermistor · 0-5 V analog | M52In intake manifold behind throttle |
| Throttle position × 1 | Not yet sourcedSourced23 | potentiometer (cable throttle) · 0-5 V analog | M52 MS41Non-adjustable |
Ignition and triggers
Tuning notes
Factory load sensing
The factory ECU measures load by MAF (hot-wire / hot-film). DME by BMW IPO table: M50 Bosch M3.1 (1991-92), M50TU M3.3.1 (1993-95), M52 Siemens MS41.1 (1996-98), S52 MS41.2. M52 HFM per BMW MS41 training. M50 HFM per parts catalog (13621747155) only. Euro S50B32 Siemens MSS50 (Wikipedia). M50 is OBD-I (no post-cat); US M52/S52 OBD-II with post-cat sensors.Medium23145
Factory oxygen sensors
Upstream: narrowband (Siemens pre-cat sensors on MS41; described as varying in resistance - element type not stated) (2 (1 per 3-cyl manifold); 1 on M52 323i/Z3). Downstream O2 sensors: varies. Closed-loop fuelling: narrowband closed loop (ECM corrects injection time); open loop under load not described.Medium23145
Driver and calibration
High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified
Common first upgrades (reported)
Builders most often report upgrading: head gasket (thicker/cut-ring with spacer to lower compression), then rods and pistons.Medium145
Valvetrain, factory engine management and weak points across every generation are on the BMW M50 / M52 / M54 guide.
Vehicles with the M50 / M52 / S50 / S52
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
30 sources
- Factory ratings: bmw-m5x (E-753) · en.wikipedia.org · reference · retrieved 2026-10-25
- BMW DME by engine (E-861) · archive.org · service-manual · retrieved 2026-10-25
- BMW M52 (MS41) (E-863) · archive.org · service-manual · retrieved 2026-10-25
- BMW M50 (E-870) · en.wikipedia.org · reference · retrieved 2026-10-25
- BMW M50/M52 block (E-1067) · en.wikipedia.org · reference · retrieved 2026-10-25
- Injector aftermarket fitment (E-1200) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector aftermarket fitment (E-1201) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector aftermarket fitment (E-1202) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector aftermarket fitment (E-1203) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / ID1050-XDS fitment (E-1230) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / ID1300-XDS fitment (E-1231) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / ID1750-XDS fitment (E-1232) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injectors / ID2600-XDS fitment (E-1233) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1050-XDS fitment table (E-1260) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1300/ID1750/ID2600 fitment tables (E-1261) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- DeatschWerks catalogue (Shopify product feed) (E-1264) · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- Fuel Injector Clinic catalogue (Shopify product feed) (E-1265) · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
- Grams Performance catalogue (E-1266) · gramsperformance.com · reference · retrieved 2026-10-25
- BMW M50/M52/S52 OEM injectors (E-1275) · e30zone.net · reference · retrieved 2026-10-25
- Injector Dynamics ID1050-XDS fitment table (E-1290) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID1300-XDS fitment table (E-1291) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Injector Dynamics ID2600-XDS fitment table (E-1292) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
- Sensors (E-1380) · archive.org · service-manual · retrieved 2026-10-25
- Part numbers (E-1387) · fcpeuro.com · reference · retrieved 2026-10-25
- fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
- deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
- deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
- deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
Evidence ids (E-…) refer to our research register; each records the source, date and confidence.

