BMW · 1992-99

BMW M3 E36 S50 / S52 ECU and tuning guide

The BMW M3 E36 S50 / S52 (1992-99) runs the M50 / M52 / S50 / S52: 2.8 L I6, naturally aspirated, port injection, cable throttle.

Researched sections show a citation and confidence for every fact.

Years1990-00
Displacement2.8L
LayoutI6
InductionNaturally aspirated
InjectionPort injection
Cam controlVANOSsingle
IgnitionCoil-on-plug
Swap demandHigh

Part of the BMW M50 / M52 / M54 family.

Modeled power and torque

Modelled estimate, not a dyno result.

M50 / M52 / S50 / S52: stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
0501001502002503003500501001502002503003501k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (190 hp at 5500 rpm, 207 lb-ft at 3950 rpm); the curve shape between peaks is modeled. Intake + exhaust + tune (pump fuel): Typical NA gains come mostly above mid-rpm.

M50 / M52 / S50 / S52 data

Factory ECU

From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.

BMW DME, 1995 E36 M3 (S50B30US)Part numbers not yet sourced.
ECU family
Bosch Motronic M3.3.1 (inferred)
Applies to
1995 US E36 M3; manual
Not for
1996+ S52 (MS41); Euro M3
Supplier
Bosch

Source says M3.3 family ran the S50 3.0 M3, but does not explicitly confirm the 1995 US car; low.

Low confidenceUnverified
BMW DME, 1996-99 E36 M3 S52 (Siemens MS41)Part numbers not yet sourced.
ECU family
Siemens MS41.1 / MS41.2
Applies to
US E36 M3 S52 01/1996-1999; manual
Not for
Euro M3 3.2 (MSS50); 1995 S50 (BF29175-S3)
Supplier
Siemens

Remanufacturer cross-reference.

Sourced · mediumE-1459

Factory ECU pinout

Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.

BMW Bosch DME M3.3 (E36 M3 S50B30, Canada, 88-pin)

The Bosch DME M3.3 is the engine control module of the S50B30 six-cylinder in the Canadian-market E36 M3 covered by BMW's 1996 wiring manual. It uses one 88-pin harness connector, X6000, and talks over CAN to a separate VANOS control module. This page transcribes all 88 cavities with function, wire colour and the connector face layout.

1996 model year E36 M3, Canadian market (pinout as documented) · Canada (BMW of North America manual, section marked CDN) · 1 connector, 88 cavities · 88 terminals sourced

DME connector X6000 (88-pin)88 cavities · 88 terminals listed · 88-pin black connector at the engine control module A6000, rear right of the engine compartment (component location chart). Three rows (28 / 27 / 33). Larger cavities carry pins 1-6, 22-34 and 49-55; the rest are the small size. Housing extension with lever guide at the left end and twin latch tabs at the right end as drawn.

Looking into the harness plug's mating face (mirror of the ECU face).

How the OEM figure is orientedBMW's figure (Connector Views 8500.0-06, Fig. 1, B880001.00) is not labelled with a viewing side. It draws pin 28 top-left, 1 top-right, 55 middle-left, 29 middle-right, 88 bottom-left and 56 bottom-right, with a lever/extension at the left and latch tabs at the right. The figure carries BMW's female-terminal (socket) icon, which indicates the harness-side plug; whether the face is the mating face or the wire side is not stated, so it is stored here as the harness plug as drawn. Check the numbers moulded on the housing before wiring.
BMW Bosch DME M3.3 (E36 M3 S50B30, Canada, 88-pin): DME connector X6000 (88-pin)housing extension / lever guide (left end as drawn)latch tab, upper rightlatch tab, lower right28: Ground2827: DME relay signal (engine control module relay)2726: Battery voltage (jump start junction point)2625: Cyl. 1 ignition coil control2524: Cyl. 3 ignition coil control2423: Cyl. 2 ignition coil control2322: Not used2221: Not used2120: Not used2019: Secondary air pump (double relay)1918: Not used1817: Camshaft position sensor signal1716: Crankshaft position/RPM sensor signal1615: Ignition control signal (connection: ground)1514: Ground, hot film air mass meter1413: Oxygen sensor I signal1312: Oxygen sensor II signal1211: Not used1110: Not used109: Not used98: "Check engine" indicator control87: Not used76: Ground, fuel injection output stages65: Cyl. 2 fuel injection valve control54: Cyl. 3 fuel injection valve control43: Cyl. 1 fuel injection valve control32: Close winding control, idle speed control valve21: Fuel pump relay control155: Ground, ignition5554: Battery voltage (DME relay output)5453: Not used5352: Cyl. 5 ignition coil control5251: Cyl. 6 ignition coil control5150: Cyl. 4 ignition coil control5049: Not used4948: A/C compressor signal (compressor control relay)4847: Crankshaft RPM speed signal TD4746: Ti-measurement signal (fuel consumption)4645: Not used4544: Ground, camshaft sensor4443: Ground, crankshaft sensor4342: Vehicle speed signal (instrument cluster)4241: Air mass meter signal4140: Ground, oxygen sensor I4039: Ground, oxygen sensor II3938: Not used3837: Oxygen sensor heater control (double relay)3736: Evaporative emission valve control3635: Not used3534: Ground, output stages3433: Cyl. 4 fuel injection valve control3332: Cyl. 6 fuel injection valve control3231: Cyl. 5 fuel injection valve control3130: Not used3029: Opening winding control, idle speed control valve2988: TxD diagnostic data link8887: RxD diagnostic data link8786: CAN-High signal (variable camshaft control module)8685: CAN-Low signal (variable camshaft control module)8584: Shield (ground)8483: Not used8382: Start revolution signal (ignition switch, terminal 50)8281: Not used8180: Not used8079: Not used7978: Engine coolant temperature7877: Engine intake air temperature7776: Not used7675: Not used7574: Not used7473: Throttle position7372: Not used7271: Ground, knock sensors and shields7170: Knock sensor signal, cyl. 1-27069: Knock sensor signal, cyl. 3-46968: Knock sensor signal, cyl. 5-66867: Not used6766: Drive-away protection signal (EWS II)6665: A/C pressure signal (pressure switch / auxiliary fan stage I)6564: A/C signal (integrated climate regulation control module)6463: Not used6362: Not used6261: Not used6160: Programming voltage (data link connector)6059: 5 V voltage supply, throttle position sensor5958: Not used5857: Not used5756: Voltage, terminal 15 (ignition switch)56
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Fuel pump relay controlrelay coil driverBR/GN (0.5 mm²)Schematic 1210.14-02: fuel pump/start identification relay K6307 pin 85 (X6307 pin 8).
2Close winding control, idle speed control valveidle valve winding driverWS/GE (0.5 mm²)Idle speed control valve Y6130 pin 1; pins 2 (close) and 29 (open) drive the two windings, common feed RT/WS on pin 2 of the valve.
3Cyl. 1 fuel injection valve controllow-side injector driverBR/WS (0.75 mm²)Injectors fed from the DME relay (RT/WS) via splice X6820.
4Cyl. 3 fuel injection valve controllow-side injector driverBR/GE (0.75 mm²)
5Cyl. 2 fuel injection valve controllow-side injector driverBR/RT (0.75 mm²)
6Ground, fuel injection output stagesDME power groundBR (1.5 mm²)The BMW table prints "full injection output stages".
7Not usedOther / not used—
8"Check engine" indicator controllamp driverGR (0.5 mm²)Instrument cluster X16 pin 16 via X20 pin 8.
9Not usedOther / not used—
10Not usedOther / not used—
11Not usedOther / not used—
12Oxygen sensor II signalO2 sensor signalGE (0.5 mm²)Heated oxygen sensor 2 B5028 pin 2; shield W5028.
13Oxygen sensor I signalO2 sensor signalGE (0.5 mm²)Heated oxygen sensor B6200 pin 2; shield W6200.
14Ground, hot film air mass metersensor groundGR/WS (0.5 mm²)Hot film air mass meter B6217 pin 4.
15Ignition control signal (connection: ground)ground—Printed as type E "Ignition control signal" with connection "Ground"; the schematic 1210.14-04 draws pin 15 dashed to ground X6454 with no colour.
16Crankshaft position/RPM sensor signalcrank sensor signalGE (0.5 mm²)Crankshaft sensor B6203 pin 1; the ETM draws the sensor with the magnet-and-coil (N S) symbol; shield W6203.
17Camshaft position sensor signalcamshaft sensor signalSW (0.5 mm²)Pin table connection: Hall effect camshaft sensor B6204 (cylinder identification), pin 1 per schematic; shield W6204.
18Not usedOther / not used—
19Secondary air pump (double relay)relay coil driverBR/WS (0.5 mm²)Double relay K5029 pin 85 (X5029 pin 10).
20Not usedOther / not used—
21Not usedOther / not used—
22Not usedOther / not used—
23Cyl. 2 ignition coil controlcoil primary drive (ignition output stage inside the DME)SW/RT (1.5 mm²)Coil-primary wires run in shield W6150 up to 10 mm before the coils.
24Cyl. 3 ignition coil controlcoil primary drive (ignition output stage inside the DME)SW/GE (1.5 mm²)
25Cyl. 1 ignition coil controlcoil primary drive (ignition output stage inside the DME)SW/WS (1.5 mm²)
26Battery voltage (jump start junction point)12 V permanent (terminal 30)RT (0.5 mm²)
27DME relay signal (engine control module relay)relay coil driverBR/BL (0.5 mm²)Engine control module relay K6300 pin 85 (X6300 pin 4).
28GroundDME groundBR/OR (1.5 mm²)To splice X6463 and ground X6454 (schematic 1210.14-06).
29Opening winding control, idle speed control valveidle valve winding driverWS/GN (0.5 mm²)Idle speed control valve Y6130 pin 3.
30Not usedOther / not used—
31Cyl. 5 fuel injection valve controllow-side injector driverBR/GN (0.75 mm²)
32Cyl. 6 fuel injection valve controllow-side injector driverBR/VI (0.75 mm²)
33Cyl. 4 fuel injection valve controllow-side injector driverBR/BL (0.75 mm²)
34Ground, output stagesDME power groundBR (1.5 mm²)
35Not usedOther / not used—
36Evaporative emission valve controlsolenoid driverBR (0.5 mm²)Evaporative emission valve Y6120 pin 2.
37Oxygen sensor heater control (double relay)relay coil driverBR/GN (0.5 mm²)Double relay K5029 pin 85 (X5029 pin 5); the relay switches the oxygen sensor heaters.
38Not usedOther / not used—
39Ground, oxygen sensor IIO2 signal groundSW (0.5 mm²)Heated oxygen sensor 2 B5028 pin 1.
40Ground, oxygen sensor IO2 signal groundSW (0.5 mm²)Heated oxygen sensor B6200 pin 1.
41Air mass meter signalanalog voltage inputGR/BL (0.5 mm²)Hot film air mass meter B6217 pin 2; the meter is fed 1.5 RT/WS from the DME relay on its pin 3.
42Vehicle speed signal (instrument cluster)vehicle speed inputSW/WS (0.5 mm²)From instrument cluster X17 pin 2 (vehicle speed output) via X20 pin 14.
43Ground, crankshaft sensorsensor groundSW (0.5 mm²)Crankshaft sensor B6203 pin 2.
44Ground, camshaft sensorsensor groundGE (0.5 mm²)Camshaft sensor B6204 pin 2.
45Not usedOther / not used—
46Ti-measurement signal (fuel consumption)injection-time (Ti) outputWS/SW (0.5 mm²)Instrument cluster X16 pin 21 and on-board computer X1071 pin 6 via X20 pin 24.
47Crankshaft RPM speed signal TDengine-speed (TD) outputSW (0.5 mm²)Instrument cluster X16 pin 20 via X20 pin 20; also to climate control and the data link (splice X1047).
48A/C compressor signal (compressor control relay)relay coil driverSW/BL (0.5 mm²)Compressor control relay K19 pin 85 (X51 pin 5); the table lists type E.
49Not usedOther / not used—
50Cyl. 4 ignition coil controlcoil primary drive (ignition output stage inside the DME)SW/BL (1.5 mm²)
51Cyl. 6 ignition coil controlcoil primary drive (ignition output stage inside the DME)SW/VI (1.5 mm²)
52Cyl. 5 ignition coil controlcoil primary drive (ignition output stage inside the DME)SW/GN (1.5 mm²)
53Not usedOther / not used—
54Battery voltage (DME relay output)12 V from DME relay (terminal 87)—The pin table connection reads "Engine control module (DME)"; schematic 1210.14-00 feeds pin 54 from relay K6300 terminal 87 through splice X6821 (6 RT/WS printed on the relay-to-splice segment; the pin-54 lead itself is not labelled).
55Ground, ignitionignition output stage ground—Drawn dashed to ground X6454; no colour printed.
56Voltage, terminal 15 (ignition switch)12 V switched (terminal 15)GN (0.5 mm²)
57Not usedOther / not used—
58Not usedOther / not used—
595 V voltage supply, throttle position sensor5 V sensor supplyRT/GE (0.5 mm²)Throttle position sensor R6252 pin 1.
60Programming voltage (data link connector)programming voltage input (PGSP)GN/BL (0.5 mm²)Data link connector X6002 pin 18.
61Not usedOther / not used—
62Not usedOther / not used—
63Not usedOther / not used—
64A/C signal (integrated climate regulation control module)digital input from climate controlVI/GR (0.5 mm²)IHKR A87y X18156 pin 18 via X20 pin 6.
65A/C pressure signal (pressure switch / auxiliary fan stage I)switch inputSW/GR (0.5 mm²)Pressure switch B9508 via X10261 pin 4; also to normal speed relay K21.
66Drive-away protection signal (EWS II)immobiliser code inputSW/VI (0.5 mm²)Electronic immobilizer control module A636 X1659 pin 4 via X20 pin 7 (0.35 GN on the EWS side).
67Not usedOther / not used—
68Knock sensor signal, cyl. 5-6knock sensor inputSW (0.35 mm²)Knock sensor B6243 pin 1; shielded.
69Knock sensor signal, cyl. 3-4knock sensor inputSW (0.35 mm²)Knock sensor B6242 pin 1; shielded.
70Knock sensor signal, cyl. 1-2knock sensor inputSW (0.35 mm²)Knock sensor B6241 pin 1; shielded.
71Ground, knock sensors and shieldssensor ground / shieldBR (0.5 mm²)Splice X5018 to the knock sensor returns (pin 2) and shields.
72Not usedOther / not used—
73Throttle positionpotentiometer inputBR/WS (0.5 mm²)Throttle position sensor R6252 pin 2; sensor ground (pin 3) goes to splice X6475.
74Not usedOther / not used—
75Not usedOther / not used—
76Not usedOther / not used—
77Engine intake air temperatureNTC thermistor inputGR (0.5 mm²)Intake air temperature sensor B6205 pin 1; return via splice X6475.
78Engine coolant temperatureNTC thermistor inputBR/RT (0.5 mm²)Coolant temperature sensor B6236 pin 1; return via splice X6475.
79Not usedOther / not used—
80Not usedOther / not used—
81Not usedOther / not used—
82Start revolution signal (ignition switch, terminal 50)12 V start inputSW/GE (0.5 mm²)Schematic 1210.14-02: from the EWS II terminal 50 output (X1659 pin 1) via X20 pin 18 and splice X6811, which also feeds relay K6307.
83Not usedOther / not used—
84Shield (ground)shield ground—Shield W9110 around the CAN pair to the VANOS module.
85CAN-Low signal (variable camshaft control module)CAN lowSW (0.5 mm²)VANOS control module A5024 X5024 pin 12. Colour printed at the VANOS-module end of the shielded pair.
86CAN-High signal (variable camshaft control module)CAN highGE (0.5 mm²)VANOS control module A5024 X5024 pin 4. Colour printed at the VANOS-module end of the shielded pair.
87RxD diagnostic data linkdiagnostic serial (RxD)WS/GE (0.5 mm²)Data link 0670.5.
88TxD diagnostic data linkdiagnostic serial (TxD)WS/VI (0.5 mm²)Data link 0670.5.

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (medium confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

Scope: BMW of North America's 1996 model-year E36 manual (cars built 9/95 to 8/96), section 1210.14 "Engine control system (DME M3.3, 6-cylinder S50 B30)", every page marked CDN (Canada). Other years and markets were not compared pin by pin; check each wire colour at the connector before cutting.

Year and market split on the linked catalog row (E36 M3, 1992-99): this pinout covers only the S50B30 car documented here. BMW training ST055 lists Siemens MS41.2 for the 1996-1999 E36 M3 (S50B32 in BMW NA naming, the US S52); that pin table was not transcribed and European M3 variants were not checked, so do not use this table for them.

VANOS is run by a separate variable camshaft control module A5024 (15-pin connector X5024) that drives the two VANOS valves, reads two camshaft sensors and talks to the DME over CAN (pins 85 and 86). That module's connector is not covered here.

Safety: disconnect the battery before unplugging the DME and never back-probe through the connector seals with sharp probes; use a break-out adapter between the DME and harness.

All factory ECU pinouts →

Plug-and-play harness

Route for this carFactory-connector adapter
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

No Haltech S3 plug-in harness is listed for this vehicle, but a Boomslang adapter harness is: it plugs into the factory ECU connector on one side and the S3 pinout on the other, so the ECU2 replaces the factory ECU without cutting the loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.

MakerHarnessFitsLink
Manual 1995 - 1995 BMW M3BF29175-S31995 US E36 M3; manual$1,080LowestMaker ↗
Manual 1996 - 1999 BMW M3BF29212-S3US E36 M3 S52 01/1996-1999; manual$1,080LowestMaker ↗
Wire-inUniversal flying lead or re-terminated factory harnessAny engine (terminate to ECU2's two Superseal 34 connectors)Universal harness from $405Maker ↗

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1995 - 1995 BMW M3

$1,080USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
BMW DME, 1995 E36 M3 (S50B30US)
ECU
Bosch · Bosch Motronic M3.3.1 (inferred)
Confidence
low

Source says M3.3 family ran the S50 3.0 M3, but does not explicitly confirm the 1995 US car; low.

Fits
1995 US E36 M3; manual
Exclusions
1996+ S52 (MS41); Euro M3
SKU
BF29175-S3
Maker fitment
BMW M3 (Manual); selector years 1995-1995; SKU label: Manual 1995 - 1995 BMW M3
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); USDM M3 1995; Haltech coil drivers required (BMW)

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1996 - 1999 BMW M3

$1,080USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
BMW DME, 1996-99 E36 M3 S52 (Siemens MS41)
ECU
Siemens · Siemens MS41.1 / MS41.2
Confidence
medium

Remanufacturer cross-reference.

Sources: E-1459

Fits
US E36 M3 S52 01/1996-1999; manual
Exclusions
Euro M3 3.2 (MSS50); 1995 S50 (BF29175-S3)
SKU
BF29212-S3
Maker fitment
BMW M3 (Manual); selector years 1996-1999; SKU label: Manual 1996 - 1999 BMW M3
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); USDM M3 1996-99; Haltech coil drivers required (BMW)

Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.

Your GAINS system for this car · pre-release

ECU2 for the M3 E36

Planned with the same rules as the configurator for this car's 6 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

  • ECU2Engine controller

    6 cyl · port injection · cable throttle

    Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harnessNone listed for this car
  2. Factory-connector → S3 adapter2 listed · from $1,080 USD listBF29175-S3
  3. Wire-inAlways possible

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the M3 E36

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Cam phasing (VVT)gated

    Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.

  4. 4
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  5. 5
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAF (hot-wire / hot-film) (medium confidence)

  6. 6
    Wideband sensorhardware

    Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller

  7. 7
    Bottom end and head sealingfactory reference

    Reported: On turbo builds the head gasket is usually cited as the first failure, with stock rods/pistons/ring lands becoming a concern around 450-550 hp (tuning blog and forum consensus); aluminium Nikasil M52 is generally regarded as less suited to boost than the iron M50 block. (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

GAINS on the M3 E36

ECU2

ECU2Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  1. E-934 Boomslang identity (sourced, high confidence)
  2. E-935 Boomslang S3 catalog size (sourced, high confidence)
  3. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  4. E-941 S3 engine harness availability (inferred, medium confidence)
  5. E-1459 E36 M3 S52 DME (supported, medium confidence)