GM / Holden 3800 V6 · 1988-04

3800 series 2 specs: horsepower, injectors and sensors

The Buick 3800 / Ecotec 3.8 V6 is a naturally aspirated 3.8 L V6 engine from GM/Holden (1988-04) with port fuel injection and wasted spark ignition. The factory ECU measures load by MAF. Below: factory specification and ratings, sensor part numbers, OEM injectors and direct-fit upgrades, triggers, swaps and tuning notes, each with its evidence.Low11311

Power: 205 hp @ 5,200 rpm · Torque: 230 lb-ft (312 Nm) @ 4,000 rpm (GM/Holden rating, not a GAINS measurement)Medium1

Factory specification

Layout, dimensions and factory hardware, each with its source.

Production years1988-04Catalog range across the variants on this page.Researched, unverified
Displacement3.8L3,791 cc from bore × strokeSourced · medium1
LayoutV6Researched, unverified
Bore × stroke96.5 × 86.4mm3.80 × 3.40 inSourced · medium1
Compression ratio9.4:1Sourced · medium1
Aspirationnaturally aspiratedResearched, unverified
Fuel injectionport fuel injectionLow confidence1311
Blockcast ironSourced · medium2
Cylinder linersnoneiron blockSourced · medium2
Connecting rods
  • Series II: castshorter, L67/L32 rods stronger
  • Series III (2004+ SC, 2005+ NA): powder-metal sinter-forged, cracked cap
Sourced · medium2
Pistons

L67 supercharged: unique, thicker crown, deeper dish, ring lands 0.1 in lower, CR 8.5:1 (vs 9.4:1 L36)

Sourced · medium2

Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.

3800 series 2 horsepower and torque

Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.

Power (GM/Holden rating)205hp @ 5,200 rpmGM 3800 Series II L36 (US SAE net); Nm convertedSourced · medium1
Torque (GM/Holden rating)230 lb-ft @ 4,000 rpm312 NmSourced · medium1
Other published ratings
  • Series II L67 supercharged: 240 hp @5200, 280 lb-ft @3600, CR 8.5
  • Series I LN3: 165 hp, 210 lb-ft
  • L27: 170 hp
  • Series I L67: 205-225 hp
  • Series III L32: up to 260 hp
  • Holden VT Ecotec L36: 147 kW @5200, 304 Nm @3600197 hp
  • VT supercharged L67: 171 kW @5200, 375 Nm @3000229 hp
  • VX: 152 kW, 305 Nm @3600
Sourced · medium1

3800 series 2 firing order

3800 series 2 injectors

The factory injector, then direct-fit upgrades the makers list for this engine.

Factory injector

Style
  • Bosch/Rochester EV1-style top-feed to 2003
  • Delphi Multec 2 from 2004L36
Low confidence1311
OEM part numbersnot confirmedDelphi 12573427 listed for 2006-08 Lucerne 3.8Low confidence1311
MakerBosch / DelphiLow confidence1311
ImpedancehighsaturatedLow confidence1311
Connector
  • EV1 / Jetronic to 2003
  • Multec 2 2004+
Low confidence1311
LengthstandardLow confidence1311
FeedtopLow confidence1311
O-ring OD (top / bottom)14/ 14 mmLow confidence1311

Direct-fit upgrades

Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.

InjectorFlowFit
Injector Dynamics ID2600-XDS · 2600.60.14.14.6Medium6101216not stated maker page does not state a single nominal figure in extracted text; ~2600 classCheck connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters
Injector Dynamics ID1050-XDS · 1050.60.14.14.6Medium3711141065 cc/min at 3.0 bar (43.5 psi), gasoline, 52 C (maker nominal)Check connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters
Injector Dynamics ID1300-XDS · 1300.60.14.14.6Medium4812151335 cc/min at 3.0 bar (43.5 psi), iso-octane, 52 C (maker nominal)Check connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters
Injector Dynamics ID1750-XDS · 1750.60.14.14.6Medium59121728 cc/min at 3.0 bar (43.5 psi), E10 cert fuel, 49 C (maker nominal)Check connector ID X-series uses USCAR connector; confirm whether the application set includes plug adapters

Sensors

Factory sensors by role: part numbers, signal type and fitment years.

SensorOEM part numbersType / signalYears and markets
Crank position × 1GM 10456161 | 10456162Cross-ref: Tridon (Holden)Low confidence17crank angle sensor (front timing cover)Holden VN-VY 3.8 1988-2004
MAF × 1GM 25008309 | 25008302 | Holden 8251803030Low confidence17MAFHolden VS-VY 3.8 V6Marketplace listings

Ignition and triggers

Ignition systemwasted sparkResearched, unverified
Crank triggercrank angle sensorfront timing coverHolden VN-VY 3.8 1988-2004Low confidence17
Valve timingnonepushrodResearched, unverified

Tuning notes

Factory load sensing

The factory ECU measures load by MAF (hot-wire / hot-film). Parts catalogs list MAF for 1990-96 Buick 3.8 NA and supercharged (Park Avenue). Holden L27/L36 (VN-VY) air metering not verified; speed-density on some 3800 applications possible (unverified).Low1

Factory oxygen sensors

Downstream O2 sensors: varies.Low1

Injector drive

Factory injector impedance: high (saturated). Connector: EV1 / Jetronic to 2003; Multec 2 2004+.Low1311

Driver and calibration

High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified

Known limits (reported)

Powder-metal Series III rods are reported to shatter rather than bend at their limit (3800 enthusiast wiki); plastic upper intake cracking near EGR is a known non-internal failure.Medium2

Valvetrain, factory engine management and weak points across every generation are on the GM / Holden 3800 V6 guide.

Vehicles with the Buick 3800 / Ecotec 3.8 V6

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

17 sources
  1. Factory ratings: GM 3800 / Holden Ecotec 3.8 (E-761) · en.wikipedia.org · reference · retrieved 2026-10-25
  2. GM 3800 (E-1077) · en.wikipedia.org · reference · retrieved 2026-10-25
  3. Injector aftermarket fitment (E-1200) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  4. Injector aftermarket fitment (E-1201) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  5. Injector aftermarket fitment (E-1202) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  6. Injector aftermarket fitment (E-1203) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  7. Injectors / ID1050-XDS fitment (E-1230) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  8. Injectors / ID1300-XDS fitment (E-1231) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  9. Injectors / ID1750-XDS fitment (E-1232) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  10. Injectors / ID2600-XDS fitment (E-1233) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  11. Injector Dynamics ID1050-XDS fitment table (E-1260) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  12. Injector Dynamics ID1300/ID1750/ID2600 fitment tables (E-1261) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  13. GM 3800 injector sizes (E-1280) · 3800wiki.com · reference · retrieved 2026-10-25
  14. Injector Dynamics ID1050-XDS fitment table (E-1290) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  15. Injector Dynamics ID1300-XDS fitment table (E-1291) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  16. Injector Dynamics ID2600-XDS fitment table (E-1292) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  17. Part numbers (E-1395) · superspares.com.au · vendor-doc · retrieved 2026-10-25

Evidence ids (E-…) refer to our research register; each records the source, date and confidence.

Not yet indexed: fewer than 3 sensors.