Toyota 3S-GTE · 1989-07

3S-GTE specs: horsepower, injectors and sensors

The 3S-GTE (Gen 2-4) is a turbocharged 2.0 L inline-4 engine from Toyota (1989-07) with port fuel injection and wasted spark ignition. Factory load sensing changes with year and market. Below: factory specification and ratings, sensor part numbers, OEM injectors and direct-fit upgrades, triggers, swaps and tuning notes, each with its evidence.Low123141586

Power: 242 hp @ 6,000 rpm · Torque: 224 lb-ft (304 Nm) @ 4,000 rpm (Toyota rating, not a GAINS measurement)1231415

Factory specification

Layout, dimensions and factory hardware, each with its source.

Production years1989-07Catalog range across the variants on this page.Researched, unverified
Displacement2.0L1,998 cc from bore × strokeSourced1231415
Layoutinline-4Researched, unverified
Bore × stroke86 × 86mm3.39 × 3.39 inSourced1231415
Compression ratio8.5:1Sourced1231415
AspirationturbochargedResearched, unverified
Recommended fuelJDM unleaded premiumSourced1231415
Fuel injectionport fuel injectionLow confidence86
Blockcast ironLow confidence231415
Cylinder linersnoneiron blockLow confidence231415
Crankshaft

5 aluminium-alloy bearings, 8 balance weights (forged on 3S-GE per Wikipedia; not stated for GTE)

Low confidence231415
Pistonsaluminium, under-piston oil squirtersLow confidence231415

Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.

3S-GTE horsepower and torque

Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.

Power (Toyota rating)242hp @ 6,000 rpmJDM JIS net 245 PS (180 kW) converted; 31.0 kgm (304.0 Nm); Gen 3 MR2 GT-S (E-SW20, 1993-96) catalogueSourced1231415
Torque (Toyota rating)224 lb-ft @ 4,000 rpm304 NmSourced1231415
Other published ratings
  • Gen2 JDM MR2 GT 1989-91: 225 PS @6000, 31.0 kgm, CR 8.8 (toyota.jp; torque rpm 3200 per Wikipedia)304 Nm
  • Gen2 US MR2 Turbo/Celica All-Trac 1990-95: 200 hp @6000, 200 lb-ft @3200271 Nm
  • Gen2 ST185 RC: 235 PS
  • Gen3 ST205 GT-Four: 255 PSWikipedia lists 244 PS
  • Gen4 Caldina GT-T (1997-2002): 260 PS @6200, 324 Nm @4400, CR 9.0
  • Gen1 ST165: 185 PS @6000, 250 Nm @4000, CR 8.5
  • Boost (Wikipedia citing enthusiast table, not OEM): Gen2 10-11 psi, Gen3 ~13 psi, Gen4 13-14 psi
Sourced1231415

3S-GTE firing order

3S-GTE injectors

The factory injector, then direct-fit upgrades the makers list for this engine.

Factory injector

Style
  • Nippondenso side-feedGen 2
  • Denso top-feedGen 3
Low confidence86
OEM part numbers23250-74200Gen 3, 540 cc, forumLow confidence86
MakerDensoLow confidence86
Impedance
  • Low (peak and hold) Gen 2
  • Gen 3 conflicting
Low confidence86
ConnectorToyotaLow confidence86
LengthotherLow confidence86
Feedside (Gen 2) / topGen 3Low confidence86

Direct-fit upgrades

Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.

InjectorFlowFit
Injector Dynamics ID1050-XDS · 1050.60.11.14B.4Medium469111065 cc/min at 3.0 bar, gasoline 52 C (maker)Needs adapter USCAR-to-Toyota plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238); Gen2 side-feed rail requires top-feed conversion (INFERRED)
Injector Dynamics ID2600-XDS · 2600.60.11.14B.4Medium5710122600 cc/min at 3.0 bar (maker)Needs adapter USCAR-to-Toyota plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238); Gen2 side-feed rail requires top-feed conversion (INFERRED)

Sensors

Factory sensors by role: part numbers, signal type and fitment years.

SensorOEM part numbersType / signalYears and markets
KnockToyota 89615-50010 (Matsushita) | Toyota 89615-33020 (-> 89615-32030) | Toyota 89615-20030 (-> 89615-32030)Sourced · medium13knock control sensorUS 1993 MR2 SW20/SW21 (3S-GTE Gen 2 and 5S-FE listed together)Engine split not stated. Gen 3/4 JDM not checked.
MAPToyota 89420-17040Sourced · medium13vacuum sensor for EFIUS 1993 MR2 (3S-GTE/5S-FE listed together)
MAFNot yet sourcedLow confidence13none listed in OEM catalogue for 1993 MR2
O2 (upstream)Toyota 89465-19435 | Toyota 89465-19525Sourced · medium13oxygen sensor (front)US 1993 MR2
O2 (downstream)Toyota 89465-17090 | Toyota 89465-17120Sourced · medium13oxygen sensor (rear)US 1993 MR2

Ignition and triggers

Ignition systemwasted sparkResearched, unverified
Valve timingVVT-iGen 4Researched, unverified

Tuning notes

Factory load sensing

The factory ECU measures load by a strategy that changes with year and market. Wikipedia: Gen1 and Gen2 use an air flow meter (MAP only for boost gauge/overboost cut); Gen3 (ST205/SW20 1994+) switched to MAP sensing. Gen4 (Caldina ST215) not stated. CONFLICT with brief hint that Gen2 is MAP.Low231415

Factory oxygen sensors

Downstream O2 sensors: varies.Low231415

Injector drive

Factory injector impedance: low (peak and hold) Gen 2; Gen 3 conflicting. Connector: Toyota.Low86

Driver and calibration

Low-impedance and direct injectors need a peak-and-hold or direct-injection driver. Any injector change also needs new flow and dead-time data in the calibration. Researched, unverified

Known limits (reported)

Forum discussion cites head-gasket sealing (Rev2 lacked steel gasket of Rev3) and reportedly thin cylinder walls on some early Rev3 blocks.Low231415

Common first upgrades (reported)

Builders most often report upgrading: forged pistons/rods and metal head gasket (forum).Low231415

Valvetrain, factory engine management and weak points across every generation are on the Toyota 3S-GTE guide.

Vehicles with the 3S-GTE (Gen 2-4)

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

15 sources
  1. Factory ratings: Toyota S family (3S-GTE) (E-727) · toyota.jp · oem · retrieved 2026-10-25
  2. Toyota 3S-GTE air metering (E-833) · en.wikipedia.org · reference · retrieved 2026-10-25
  3. Toyota 4A-GE / 4A-GZE / 3S-GTE internals (E-1042) · en.wikipedia.org · reference · retrieved 2026-10-25
  4. Injector aftermarket fitment (E-1200) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  5. Injector aftermarket fitment (E-1203) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  6. Injectors / ID1050-XDS fitment (E-1230) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  7. Injectors / ID2600-XDS fitment (E-1233) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  8. Injectors / 3S-GTE stock (E-1245) · toymods.org.au · reference · retrieved 2026-10-25
  9. Injector Dynamics ID1050-XDS fitment table (E-1260) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  10. Injector Dynamics ID1300/ID1750/ID2600 fitment tables (E-1261) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  11. Injector Dynamics ID1050-XDS fitment table (E-1290) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  12. Injector Dynamics ID2600-XDS fitment table (E-1292) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  13. OEM sensor PNs (Toyota MR2 SW20) (E-1364) · toyotapartsdeal.com · vendor-doc · retrieved 2026-10-25
  14. OEM turbo: toyota-ct26 (E-10068) · en.wikipedia.org · reference · retrieved 2026-11-04
  15. OEM turbo: toyota-ct20 (E-10085) · en.wikipedia.org · reference · retrieved 2026-11-04

Evidence ids (E-…) refer to our research register; each records the source, date and confidence.