Factory specification
Layout, dimensions and factory hardware, each with its source.
- Casthypereutectic per 8020automotive
- Forged pistons and lighter crank on later C63 variant (8020automotive)
- Pre-2011 head bolts prone to corrosion/failure (coolant into combustion chamber)
- Revised bolts from 20118020automotive
Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.
M156 6.2 horsepower and torque
Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.
- CLK 63: 475 hp @6800, 630 Nm @5200482 PS
- E 63/CLS 63: 507 hp @6800, 630 Nm @5200514 PS
- ML 63: 503 hp
- C 63 Edition 507: 500 hp507 PS
- Later S/E/SL/CL 63: 518 hp, 630 Nm525 PS
- One US release copy says 457 bhp for C 63 (conflict)
M156 6.2 firing order
M156 6.2 injectors
The factory injector, then direct-fit upgrades the makers list for this engine.
Factory injector
Direct-fit upgrades
Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.
| Injector | Flow | Fit |
|---|---|---|
| DeatschWerks DW 600cc matched set · 17MX-01-0600-89 | 600 cc/min maker listing nominal (rating pressure not stated in listing) | Check connector connector not stated on maker listing |
| DeatschWerks DW 850cc matched set · 17MX-01-0850-88 | 850 cc/min maker listing nominal (rating pressure not stated in listing) | Check connector connector not stated on maker listing |
| DeatschWerks DW 1100cc matched set · 17MX-01-1100-87 | 1100 cc/min maker listing nominal (rating pressure not stated in listing) | Check connector connector not stated on maker listing |
Sensors
Factory sensors by role: part numbers, signal type and fitment years.
| Sensor | OEM part numbers | Type / signal | Years and markets |
|---|---|---|---|
| Knock | Not yet sourcedCross-ref: Bosch 0 261 231 188Sourced · medium5 | piezo knock sensor | ML63 W164 M156.980 2006-11 |
| O2 (upstream) | MB A0035428218 / 0045420718 | Bosch 0 258 006 749Low confidence6 | oxygen sensor (upstream) | C63 AMG M156.985 2008-14eBay listing |
Ignition and triggers
Tuning notes
Factory load sensing
The factory ECU measures load by MAF (hot-wire / hot-film). Bosch ME 9.7 per French forum; two MAF sensors (one per side) implied by vendor airbox listing (not a tuner doc but low quality). O2 configuration not sourced. Researched, unverified
Driver and calibration
High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified
Known limits (reported)
Head bolts (pre-2011) and valvetrain (lifters/cam lobes) are more commonly cited weaknesses than the bottom end.Medium2
Common first upgrades (reported)
Builders most often report upgrading: head bolts (on pre-2011 engines), headers.Medium2
Valvetrain, factory engine management and weak points across every generation are on the Mercedes-AMG M113 / M156 guide.
Vehicles with the M156 6.2
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
9 sources
- Factory ratings: Mercedes M113/M156 V8 (E-759) · en.wikipedia.org · reference · retrieved 2026-10-25
- Mercedes M156 (E-1074) · australiancar.reviews · press · retrieved 2026-10-25
- DeatschWerks catalogue (Shopify product feed) (E-1264) · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- Mercedes M156 OEM injector (E-1278) · vrpspeed.com · reference · retrieved 2026-10-25
- Cross reference (E-1389) · superspares.com.au · vendor-doc · retrieved 2026-10-25
- Part numbers (E-1404) · ebay.com · vendor-doc · retrieved 2026-10-25
- deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
- deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
Evidence ids (E-…) refer to our research register; each records the source, date and confidence.
Not yet indexed: fewer than 3 sensors.

