Honda F20C / F22C · 2000-09

F20C specs: horsepower, injectors and sensors

The F20C / F22C (S2000) is a naturally aspirated 2.0 L inline-4 engine from Honda (2000-09) with port fuel injection and coil-on-plug ignition. The factory ECU measures load by MAP speed-density. Below: factory specification and ratings, sensor part numbers, OEM injectors and direct-fit upgrades, triggers, swaps and tuning notes, each with its evidence.Low132978

Power: 240 hp @ 8,300 rpm · Torque: 153 lb-ft (207.4 Nm) @ 7,500 rpm (Honda rating, not a GAINS measurement)1

Factory specification

Layout, dimensions and factory hardware, each with its source.

Production years2000-09Catalog range across the variants on this page.Researched, unverified
Displacement2.0L1,997 cc from bore × strokeSourced1
Layoutinline-4Researched, unverified
Bore × stroke87 × 84mm3.43 × 3.31 inSourced1
Compression ratio11.0:1Sourced1
Redline9,000rpmSourced1
Aspirationnaturally aspiratedResearched, unverified
Recommended fuelpremium unleadedSourced1
Fuel injectionport fuel injectionLow confidence978
Blockaluminiumone-piece die castingSourced · medium45
Cylinder linersFRM liners cast integral with the blockSourced · medium45
Main capsladder-frame stiffener with cast-iron bearing insertsSourced · medium45
Crankshaftforged steel, carburized and heat-treatedSourced · medium45
Connecting rodsforged steel, carburized and heat-treatedSourced · medium45
Pistonsforged aluminium, minimal skirtSourced · medium45

Facts tagged “Researched, unverified” come from our engine catalog without a cited source yet.

F20C horsepower and torque

Ratings as the manufacturer published them, with their basis. They are not GAINS measurements or tuning results.

Power (Honda rating)240hp @ 8,300 rpmSAE net, US F20C (2000-03 S2000 AP1) per Honda 2004 S2000 intro release; 9000 rpm = fuel cutoff; bore/stroke from Wikipedia; fuel per KBB listingSourced1
Torque (Honda rating)153 lb-ft @ 7,500 rpm207.4 NmSourced1
Other published ratings
  • F22C1: 240 hp @7800, 162 lb-ft @6500 (Honda; third-party lists 237 hp / 162 lb-ft @6800 after SAE J1349 revision), redline/fuel cut 8200 (Wikipedia prose says 8000), CR 11.1, 87 x 90.7 mm2004-09 S2000
  • JDM F20C: CR 11.7Wikipedia
Sourced1

F20C firing order

F20C injectors

The factory injector, then direct-fit upgrades the makers list for this engine.

Factory injector

StyleHonda top-feedKeihin/Denso family; maker not confirmedLow confidence978
OEM part numbers16450-PZX-00306-09 AP2, Honda dealer catalogueLow confidence978
ImpedancehighsaturatedLow confidence978
ConnectorHonda OBD2Low confidence978
LengthshortLow confidence978
FeedtopLow confidence978

Direct-fit upgrades

Sets the maker lists for this engine. Fit is the maker’s own statement; flow is the maker’s rating and test basis.

InjectorFlowFit
DeatschWerks DW 440cc matched set · 17U-09-0440-415440 cc/min maker rating (basis not stated on page)Needs adapter USCAR-to-OEM plug adapter (DW page states USCAR connector; adapter inclusion not stated)
DeatschWerks DW 650cc matched set · 17U-08-0650-413650 cc/min maker rating (basis not stated on page)Needs adapter USCAR-to-OEM plug adapter (DW page states USCAR connector; adapter inclusion not stated)
Fuel Injector Clinic FIC 445cc High-Z set · is117-0445h14445 cc/min at 43.5 psi (3 bar), CF-16B fluid 90 F (maker)Needs adapter USCAR-to-Honda OBD2 plug adapters PADPUtoH4 (optional) or solder-in pigtails PGTUSC4 (included)
Fuel Injector Clinic FIC 650cc High-Z set · is116-0650h16650 cc/min at 43.5 psi (3 bar), CF-16B fluid 90 F (maker)Needs adapter USCAR-to-Honda OBD2 plug adapters PADPUtoH4 (optional) or solder-in pigtails PGTUSC4 (included)
Injector Dynamics ID1050-XDS · 1050.48.11.F20.46710111065 cc/min at 3.0 bar, gasoline 52 C (maker)Needs adapter USCAR-to-Honda OBD2 plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238)
Injector Dynamics ID1050-XDS · 1050.48.14.14.46710111065 cc/min at 3.0 bar, gasoline 52 C (maker)Needs adapter USCAR-to-Honda OBD2 plug adapters (ID connector is USCAR; adapters sold separately per retailer listings E-1238)

Sensors

Factory sensors by role: part numbers, signal type and fitment years.

SensorOEM part numbersType / signalYears and markets
KnockHonda 30530-PCX-003Sourced12knock sensorUS S2000 2001 (F20C) and 2004 (F22C1)
MAPHonda 37830-PAA-S00 (replaces 37830-P0G-S00)Sourced12MAP sensor ('Sensor Set, MAP')US S2000 2004
MAFNot yet sourcedSourced · medium12none listed in OEM catalogue (speed-density, MAP-based)
O2 (upstream)Honda 36531-PCX-014 (2001; replaces 36531-PCX-004) | Honda 36531-PZX-A01 (2004)Sourced12oxygen sensor (front)US 2000-03 F20C vs 2004+ F22C1 splitDenso 234-9065 is retail-listed for S2000 2006-09 (not catalogue-verified, not used).
O2 (downstream)Honda 36532-PCX-A01 (2001) | Honda 36532-PZX-A01 (2004)Sourced12oxygen sensor (rear)US 2001 vs 2004

Ignition and triggers

Ignition systemcoil-on-plugResearched, unverified
Valve timingVTECResearched, unverified

Tuning notes

Factory load sensing

The factory ECU measures load by MAP speed-density. Honda 2008 S2000 press lists intake-manifold pressure + exhaust oxygen sensing and applies an LAF sensor for LEV-2 / Tier 2 Bin 5. F22C DBW not stated in press. Early F20C sensor type not found. US-market car so OBD-II downstream present.Medium32

Factory oxygen sensors

Upstream: F22C1 (2004-09 US): LAF linear A/F upstream (Honda press, LEV-2); F20C 2000-03: not confirmed (likely narrowband, unsourced). Downstream O2 sensors: yes. Closed-loop fuelling: closed loop on upstream sensor at part load; open loop enrichment at WOT (generic, not S2000-specific).Medium32

Injector drive

Factory injector impedance: high (saturated). Connector: Honda OBD2.Low978

Driver and calibration

High-impedance injectors run from a saturated driver. Any injector change needs new flow and dead-time data in the calibration. Researched, unverified

Known limits (reported)

Forum reports put the stock bottom end in the ~400+ whp class on boost; some builders resleeve (ductile iron) for big power, and forum posters debate whether the FRM sleeves or head-gasket sealing go first (forum, low confidence).Medium45

Common first upgrades (reported)

Builders most often report upgrading: sleeves (ductile iron, e.g. Darton) and lower-compression forged pistons when going beyond stock-bottom-end power (forum).Medium45

Valvetrain, factory engine management and weak points across every generation are on the Honda F20C / F22C guide.

Vehicles with the F20C / F22C (S2000)

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

16 sources
  1. Factory ratings: Honda F20C / F22C1 (S2000) (E-719) · hondanews.com · oem · retrieved 2026-10-25
  2. Honda PGM-FI closed loop (E-821) · ej9.ru · community · retrieved 2026-10-25
  3. Honda F22C LAF (E-828) · hondanews.com · oem · retrieved 2026-10-25
  4. Honda F20C/F22C1 internals (E-1033) · hondanews.com · oem · retrieved 2026-10-25
  5. Honda F20C limits (E-1034) · s2ki.com · community · retrieved 2026-10-25
  6. Injector aftermarket fitment (E-1200) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  7. Injectors / ID1050-XDS fitment (E-1230) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  8. Injectors / FIC Honda sets (E-1234) · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
  9. Injectors / S2000 OEM (E-1241) · s2ki.com · community · retrieved 2026-10-25
  10. Injector Dynamics ID1050-XDS fitment table (E-1260) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  11. Injector Dynamics ID1050-XDS fitment table (E-1290) · injectordynamics.com · vendor-doc · retrieved 2026-10-25
  12. OEM sensor PNs (Honda S2000) (E-1356) · hondapartsnow.com · vendor-doc · retrieved 2026-10-25
  13. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  14. fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25
  15. deatschwerks.com product listing · deatschwerks.com · vendor-doc · retrieved 2026-10-25
  16. fuelinjectorclinic.com product listing · fuelinjectorclinic.com · vendor-doc · retrieved 2026-10-25

Evidence ids (E-…) refer to our research register; each records the source, date and confidence.