Engine: F20C / F22C (S2000)
Part of the Honda F20C / F22C family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (240 hp at 8300 rpm, 153 lb-ft at 7500 rpm); the curve shape between peaks is modeled. Intake + exhaust + tune (pump fuel): Typical NA gains come mostly above mid-rpm.
F20C / F22C (S2000) data
- Load sensing
- MAP speed-density
- O2 sensor
- F22C1 (2004-09 US): LAF linear A/F upstream (Honda press, LEV-2); F20C 2000-03: not confirmed (likely narrowband, unsourced)
- Closed loop
- closed loop on upstream sensor at part load; open loop enrichment at WOT (generic, not S2000-specific)
- Block
- aluminium (one-piece die casting)
- Rods / pistons
- forged steel, carburized and heat-treated · forged aluminium, minimal skirt
- Reported limit
- ~400-500 whp reported on stock bottom end in individual S2000 forum builds (forum anecdote; one build 424 whp pump / 507 whp race gas)
- Factory
- Honda top-feed (Keihin/Denso family; maker not confirmed)
- Impedance
- high (saturated)
- Direct-fit upgrades
- 6 maker-listed
- Knock
- Honda 30530-PCX-003
- MAP / MAF
- Honda 37830-PAA-S00 (replaces 37830-P0G-S00)
- O2 (upstream)
- Honda 36531-PCX-014 (2001; replaces 36531-PCX-004) | Honda 36531-PZX-A01 (2004)
Factory ECU
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Honda/Keihin 37820-PCX
- Applies to
- AP1 2000-04 and AP2 2005 (non-DBW)
- Not for
- not 2006+ DBW AP2
Examples from forum and used-parts listings; suffix-to-year mapping inconsistent across sellers. Supplier not confirmed.
- ECU family
- Honda S2000 cable-throttle ECM
- Applies to
- 2000-05 S2000 manual; PCX = AP1 (2000-03), PZX = AP2 (2004-05)
- Not for
- Not 2006+ drive-by-wire
Label spans AP1 (PCX) and early AP2 (PZX) ECUs; PCX-A02 example for 2000-02 per owner/catalogue mention.
Factory ECU pinout: pending
No OEM pin table is in our library yet for the F20C / F22C (S2000) factory ECU. We only publish pinouts drawn from the OEM service manual or the maker's own documents, and none has been sourced yet. Until then, wire from the harness maker's instructions or the factory service manual.
Plug-and-play harness
A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
| Nexus S2/S3 Plug n Play Adapter Harness Honda AP1HT-186330 | AP1 2000-04 and AP2 2005 (non-DBW) | $535Lowest | Maker ↗ | |
![]() | Manual 2000 - 2005 Honda S2000BF29006-S3 | 2000-05 S2000 manual; PCX = AP1 (2000-03), PZX = AP2 (2004-05) | $840 | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |
Nexus S2/S3 Plug n Play Adapter Harness Honda AP1
- Plugs into
Honda S2000 AP1 ECU (37820-PCX) · 37820-PCX-A01, 37820-PCX-A02…
- OEM part numbers
- 37820-PCX-A01, 37820-PCX-A02, 37820-PCX-J02, 37820-PCX-J03
- ECU
- Honda/Keihin 37820-PCX
- Confidence
- medium
Examples from forum and used-parts listings; suffix-to-year mapping inconsistent across sellers. Supplier not confirmed.
Sources: E-1440
- Fits
- AP1 2000-04 and AP2 2005 (non-DBW)
- Exclusions
- not 2006+ DBW AP2
- SKU
- HT-186330
- Maker fitment
- Honda S2000 AP1 (00-04) and AP2 (05) non-DBW only
- Maker notes
- kit HT-213314

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2000 - 2005 Honda S2000
- Plugs into
Honda S2000 ECM (AP1 F20C / AP2 F22C) · 37820-PCX-A02
- OEM part numbers
- 37820-PCX-A02
- ECU
- Honda S2000 cable-throttle ECM
- Confidence
- low
Label spans AP1 (PCX) and early AP2 (PZX) ECUs; PCX-A02 example for 2000-02 per owner/catalogue mention.
Sources: E-1462
- Fits
- 2000-05 S2000 manual; PCX = AP1 (2000-03), PZX = AP2 (2004-05)
- Exclusions
- Not 2006+ drive-by-wire
- SKU
- BF29006-S3
- Maker fitment
- Honda S2000 (Manual); selector years 2000-2005; SKU label: Manual 2000 - 2005 Honda S2000
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2)
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the S2000 AP1
Planned with the same rules as the configurator for this car's 4 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

- Price TBA
ECU2Engine controller
4 cyl · port injection · cable throttle
Full sequential fuel and spark for this 4-cylinder on a cable throttle, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harness1 listed · from $535 USD listHT-186330
- Factory-connector → S3 adapter1 listed · from $840 USD list
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
Swap guides
Into the S2000 AP1
How GAINS approaches the S2000 AP1
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3VTEC crossoverplanned
VTEC engagement is treated as a load and rpm surface where the two cam profiles cross on torque, learned from logs rather than a single fixed rpm.
- 4Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 5Factory load sensingfactory reference
What the factory ECU measures load with: MAP speed-density (medium confidence)
- 6Wideband sensorhardware
Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller
- 7Bottom end and head sealingfactory reference
Reported: Forum reports put the stock bottom end in the ~400+ whp class on boost; some builders resleeve (ductile iron) for big power, and forum posters debate whether the FRM sleeves or head-gasket sealing go first (forum, low confidence). (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
GAINS on the S2000 AP1
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-902 Haltech S3 compatibility wording (sourced, high confidence)
- E-910 Haltech S3 adapter harness page (sourced, high confidence)
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)
- E-1440 Honda S2000 AP1 ECU (reported, low confidence)
- E-1462 S2000 AP1 ECM (unverified-secondary, low confidence)



