Factory ECU
The OBD0-to-OBD1 change mid-generation matters for harness and ECU swaps. Confirm the year and ECU connector style before buying parts.
Factory ECU pinout
No OEM-grade ECM/PCM terminal table could be read for this guide (the factory manuals located online are image-only). Competitor plug-in manuals were not used, by policy. Needed: Acura Integra 1990-1993 Service Manual and Electrical Troubleshooting Manual, ECU connector terminal tables (OBD0 1990-91 and OBD1 1992-93 separately).
Drivetrain
Chassis integration
Simple chassis electronics: tach from the ignition system, a VSS for the speedometer and a coolant gauge sender.
Tuning notes
The B18A1 is a popular bottom end for low-boost and 'LS-VTEC' style builds, but it is non-VTEC from the factory. A VTEC head conversion needs an oil feed and a VTEC-capable ECU.
Popular swaps
Later B18C/B16A engines, or K-series via fabricated mounts, are common upgrades. The DA's cable-clutch heritage affects transmission choice.
GAINS on the Acura Integra DA (1990-93): B18A1 and B17A1 GS-R guide
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Frequently asked
How much power does a 1990 Integra have?
Acura rates the 1990-91 1.8-litre B18 at 130 hp; 1992-93 LS/GS engines were rated at 140 hp.2
Is the 1990-93 Integra OBD0 or OBD1?
1990-91 cars are OBD0 and 1992-93 cars are OBD1.3
Is the B18A1 an interference engine?
Yes, the 1990-95 1.8 Integra is listed as an interference engine.1
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- Timing belts and interference engines · AA1Car Automotive Diagnostic Library (Larry Carley) · press · retrieved 2026-10-25
- Acura Integra Heritage and Milestones · Acura (acuranews.com) · press · retrieved 2026-10-25
- Honda B engine · Wikipedia · community · retrieved 2026-10-25

