Vehicle guide

Honda CRX EF8 / Civic EF9 SiR (1988-91): B16A, OBD0 and swap guide tuning guide

In Japan, EF8 denotes the CRX SiR and EF9 the Civic SiR hatch; both carried the B16A, Honda's first B-series VTEC. North American CRX Si models used D-series SOHC engines, which is why B16A and later K-series swaps into US CRXs are so common. The chassis shares the EF Civic's double-wishbone suspension and mount layout.

Reviewed by GAINS editorial team on 2026-11-04.

Factory ECU

SiR engineB16A 1.6 L DOHC VTEC: 81 x 77.4 mm, 10.2:1 (first generation)Low confidence4
Diagnostics generationOBD0-era ECUsLow confidence4

Replacement mount kits for factory B16A cars list EF8/EF9 compatibility, which confirms these chassis codes were factory B16A applications.

Factory ECU pinout

No OEM-grade ECM/PCM terminal table could be read for this guide (the factory manuals located online are image-only). Competitor plug-in manuals were not used, by policy. Needed: Honda 1988-1991 Civic/CRX Service Manual (and JDM EF8/EF9 SiR manual for B16A models), ECU connector terminal tables.

Drivetrain

Transmission choice (cable- or hydraulic-clutch B-series, or a K-series manual) dictates the mount kit, axles and clutch actuation.

Chassis integration

SuspensionDouble-wishbone front and rearshared EF platformSourced · medium2

Tuning notes

Being a light two-seater, the CRX responds strongly to throttle-response and gearing changes. Calibration effort is best spent on transient fuelling and the VTEC crossover.

Popular swaps

Factory B16A replacement mounts

Hasport replacement kit listed for EF8, EF9, EE8 and EE9 chassis with stock B16A

Sourced · medium3
K-series mountsHasport EFK covers 88-91 Civic and CRXSourced · medium1

GAINS on the Honda CRX EF8 / Civic EF9 SiR (1988-91): B16A, OBD0 and swap guide

ECU2

ECU2Full sequential fuel and spark for this 4-cylinder on a cable throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

What engine is in the CRX SiR EF8?

The B16A 1.6-litre DOHC VTEC.4

Is EF9 a CRX?

No. EF9 is the Civic SiR hatch; EF8 is the CRX SiR. Both used the B16A.4

Can you K-swap a CRX?

Yes. Hasport's EFK kit covers 88-91 Civic and CRX.1

Is the CRX OBD0?

Yes, 1988-91 Honda ECUs are OBD0-era.4

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. EFK K-Series Mount Kit (88-91 Civic/CRX) · Hasport Performance · vendor-doc · retrieved 2026-10-25
  2. Honda Civic Si Timeline and Milestones · American Honda Motor Co. (hondanews.com) · press · retrieved 2026-10-25
  3. Hasport Performance B-Series Engine Swap Mount Kit (88-91 Civic/CRX) listing · Hybrid Racing · vendor-doc · retrieved 2026-10-25
  4. Honda B engine · Wikipedia · community · retrieved 2026-10-25