Part of the Subaru EJ family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (230 hp at 5600 rpm, 235 lb-ft at 3600 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.
EJ255 (WRX / Legacy GT / Forester XT) data
- Load sensing
- MAF (hot-wire / hot-film)
- O2 sensor
- wideband A/F (UEGO)
- Closed loop
- Not yet sourced
- Block
- aluminium
- Rods / pistons
- shared with EJ257 (Crawford) · cast (Crawford)
- Reported limit
- ~400 whp before stock rods/pistons become weak link (Crawford, vendor)
- Factory
- 2005-06 Legacy GT: side-feed; 2006+ WRX / 2007+ LGT / FXT: top-feed
- Impedance
- high (saturated)
- Direct-fit upgrades
- 6 maker-listed
- Knock
- 22060AA100 (listed 2.0/2.5 turbo)
- MAP / MAF
- absolute pressure sensor
- O2 (upstream)
- wideband A/F sensor
Platform background
The EJ255 turbo powered the US Legacy GT/Outback XT (250 hp from 2005) and Forester XT, with AU Liberty GT and Forester XT equivalents. All BL/BP Legacys have drive-by-wire. SI-Drive arrived for MY07-09, and turbo models offered a 5-speed automatic or 5/6-speed manual. JDM/AU 2.0 litre Legacy GTs used the Dual AVCS EJ20X/EJ20Y instead. No OEM ECM pinout source was found.
Factory ECU
These cars share the EJ255's MAF-based strategy, adaptive knock control and intake AVCS, with DBW throttle on the Legacy. Reflash is the usual route. The automatic Legacy GT's transmission controller relies on engine torque data, so standalone conversions are more complex on automatics.
Factory ECU: harness cross-reference
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Subaru BL/BP Legacy GT ECM (MY05-06)
- Applies to
- 2005-2006 Legacy GT / GT Limited; USDM (transmission not stated)
2005 GT numbers; two families (AJ18x, AJ66x) likely M/T vs A/T but catalogue does not say. MY06 not looked up.
- ECU family
- Subaru BL/BP Legacy GT ECM (MY07-09)
- Applies to
- 2007-2009 Legacy GT; USDM
2007 GT numbers (three families, transmission/trim split not stated). MY08-09 not looked up.
- ECU family
- Subaru SG Forester XT ECM
- Applies to
- 2004-2005 Forester XT; USDM
2005 XT numbers; two families (AJ57x, AJ58x), transmission not stated. MY04 not looked up.
- ECU family
- Subaru SG Forester XT ECM
- Applies to
- 2006-2007 Forester XT, manual; USDM
No number looked up for MY06-07.
Factory ECU pinout: pending
No OEM pin table is in our library yet for the EJ255 (WRX / Legacy GT / Forester XT) factory ECU. No OEM-grade source found. Required: Subaru 2005-2009 Legacy/Outback and 2004-2008 Forester service manuals (STIS), 'Engine Control Module (ECM) I/O signal' table for the EJ255 turbo, and the wiring diagram books. Until then, wire from the harness maker's instructions or the factory service manual.
Factory ECU pinout
No OEM-grade source found. Required: Subaru 2005-2009 Legacy/Outback and 2004-2008 Forester service manuals (STIS), 'Engine Control Module (ECM) I/O signal' table for the EJ255 turbo, and the wiring diagram books.
Plug-and-play harness
No Haltech S3 plug-in harness is listed for this vehicle, but a Boomslang adapter harness is: it plugs into the factory ECU connector on one side and the S3 pinout on the other, so the ECU2 replaces the factory ECU without cutting the loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
![]() | Manual 2005 - 2006 Subaru Legacy GTBF29220-S3 | 2005-2006 Legacy GT / GT Limited; USDM (transmission not stated) | $840Lowest | Maker ↗ |
![]() | Manual 2007 - 2009 Subaru Legacy GTBF29221-S3 | 2007-2009 Legacy GT; USDM | $840Lowest | Maker ↗ |
![]() | Manual 2004 - 2005 Subaru Forester XTBF29231-S3 | 2004-2005 Forester XT; USDM | $840Lowest | Maker ↗ |
![]() | Manual 2006 - 2007 Subaru Forester XTBF29232-S3 | 2006-2007 Forester XT, manual; USDM | $840Lowest | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2005 - 2006 Subaru Legacy GT
- Plugs into
Subaru ECM (EJ255, 2005-06 Legacy GT, BL/BP) · 22611AJ18A, 22611AJ18B…
- OEM part numbers
- 22611AJ18A, 22611AJ18B, 22611AJ18C, 22611AJ18D, 22611AJ66A, 22611AJ66B, 22611AJ66C, 22611AJ66D
- ECU
- Subaru BL/BP Legacy GT ECM (MY05-06)
- Confidence
- medium
2005 GT numbers; two families (AJ18x, AJ66x) likely M/T vs A/T but catalogue does not say. MY06 not looked up.
Sources: E-1495
- Fits
- 2005-2006 Legacy GT / GT Limited; USDM (transmission not stated)
- SKU
- BF29220-S3
- Maker fitment
- Subaru Legacy GT (Manual); selector years 2005-2006; SKU label: Manual 2005 - 2006 Subaru Legacy GT
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); Legacy GT 2005-06

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2007 - 2009 Subaru Legacy GT
- Plugs into
Subaru ECM (EJ255, 2007-09 Legacy GT / spec.B) · 22611AL80A, 22611AL80B…
- OEM part numbers
- 22611AL80A, 22611AL80B, 22611AL80C, 22611AL81A, 22611AL81B, 22611AL81C, 22611AL82A, 22611AL82B
- ECU
- Subaru BL/BP Legacy GT ECM (MY07-09)
- Confidence
- medium
2007 GT numbers (three families, transmission/trim split not stated). MY08-09 not looked up.
Sources: E-1495
- Fits
- 2007-2009 Legacy GT; USDM
- SKU
- BF29221-S3
- Maker fitment
- Subaru Legacy GT (Manual); selector years 2007-2009; SKU label: Manual 2007 - 2009 Subaru Legacy GT
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); Legacy GT 2007-09

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2004 - 2005 Subaru Forester XT
- Plugs into
Subaru ECM (EJ255, 2004-05 Forester XT, SG) · 22611AJ570, 22611AJ571…
- OEM part numbers
- 22611AJ570, 22611AJ571, 22611AJ572, 22611AJ573, 22611AJ580, 22611AJ581, 22611AJ582, 22611AJ583
- ECU
- Subaru SG Forester XT ECM
- Confidence
- medium
2005 XT numbers; two families (AJ57x, AJ58x), transmission not stated. MY04 not looked up.
Sources: E-1496
- Fits
- 2004-2005 Forester XT; USDM
- SKU
- BF29231-S3
- Maker fitment
- Subaru Forester XT (Manual); selector years 2004-2005; SKU label: Manual 2004 - 2005 Subaru Forester XT
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); Forester XT 2004-05

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2006 - 2007 Subaru Forester XT
- Plugs into
Subaru ECM (EJ255, 2006-07 Forester XT, SG facelift)
- ECU
- Subaru SG Forester XT ECM
- Confidence
- low
No number looked up for MY06-07.
- Fits
- 2006-2007 Forester XT, manual; USDM
- SKU
- BF29232-S3
- Maker fitment
- Subaru Forester XT (Manual); selector years 2006-2007; SKU label: Manual 2006 - 2007 Subaru Forester XT
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); Forester XT 2006-07
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the Legacy GT / Forester XT BL / BP, SG / SH
Planned with the same rules as the configurator for this car's 4 cyl · port injection · drive-by-wire. The factory ECU is unplugged and replaced; nothing is written to it.
- Price TBA
ECU2Engine controller
4 cyl · port injection · drive-by-wire
Full sequential fuel and spark for this 4-cylinder, and its electronic throttle, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- Drive-by-wire built inFour half-bridges run up to two electronic throttles, with pedal and throttle sensors on the ECU's own inputs and a windowed watchdog that cuts the motors in hardware on a fault.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harnessNone listed for this car
- Factory-connector → S3 adapter4 listed · from $840 USD listBF29220-S3
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
How GAINS approaches the Legacy GT / Forester XT BL / BP, SG / SH
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3Cam phasing (VVT)gated
Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.
- 4Boost controlgated
A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.
- 5Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 6Factory load sensingfactory reference
What the factory ECU measures load with: MAF (hot-wire / hot-film) (medium confidence)
- 7Wideband sensorhardware
the factory sensor is already an A/F type; for tuning, fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller (factory A/F sensors are not LSU-compatible)
- 8Bottom end and head sealingfactory reference
Reported: Cast piston ringland failure and open-deck cylinder flex/head gasket failure commonly reported (Crawford, vendor). (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
Drivetrain
Chassis integration
Three modes with unique ECU and TCU settings (Intelligent, Sport, Sport Sharp), MY07-09
Low confidence4Tuning notes
The EJ255 in these cars uses forged rods but cast pistons, and its turbos are packaged differently from the WRX's. Turbo upgrades usually mean model-specific up-pipes and intakes. Keep knock margins conservative and log intake temperatures, especially on top-mount-intercooler Forester XTs.
GAINS on the Legacy GT / Forester XT BL / BP, SG / SH
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Frequently asked
What engine is in the 2005-2009 Legacy GT?
The 2.5 litre EJ255 turbo, rated 250 hp and 250 lb-ft in the US.21
What turbo does the Forester XT use?
A Mitsubishi TD04L on the SG Forester XT; the SH used a revised TD04L.1
Is the Legacy GT drive-by-wire?
Yes. All BL/BP Legacy models use electronic throttle control.4
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- Subaru EJ255 Engine · AustralianCar.Reviews · press · retrieved 2026-10-25
- Subaru Announces North American Legacy to Sport 250-HP · Auto123 · press · retrieved 2026-10-25
- Subaru EJ engine · Wikipedia · community · retrieved 2026-10-25
- Subaru Legacy (fourth generation) · Wikipedia · community · retrieved 2026-10-25
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)
- E-1495 harness ECU xref: Subaru Legacy GT 2005 and 2007 (verified, high confidence)
- E-1496 harness ECU xref: Subaru 2005 Forester XT (verified, high confidence)


