Engine: EJ257 (STI)
Part of the Subaru EJ family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (305 hp at 6000 rpm, 290 lb-ft at 4000 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.
EJ257 (STI) data
- Load sensing
- MAF (hot-wire / hot-film)
- O2 sensor
- wideband A/F (UEGO)
- Closed loop
- Not yet sourced
- Block
- aluminium
- Rods / pistons
- cast hypereutectic, high top ring (MotoIQ); MY19 new stronger alloy (Wikipedia)
- Reported limit
- ~340 hp conservative stock bottom end on pump gas (MotoIQ); ~350-400 whp ringland threshold (Crawford, vendor)
- Factory
- 2004-06 STI: side-feed; 2007+ STI: top-feed · 565 cc/min
- Impedance
- high (saturated)
- Direct-fit upgrades
- 7 maker-listed
- Knock
- 22060AA111 (2005 STI)|22060AA100
- MAP / MAF
- 22627AA380 (2006 STI)|22627AA490 (2008-14 STI)
- O2 (upstream)
- wideband A/F sensor
Platform background
The VA WRX STI kept the EJ257 2.5 litre turbo (export) or EJ207 (Japan) with Dual AVCS, now in a semi-closed-deck block with reinforcing ribs and a nitride-hardened crank. It drives through a reinforced 6-speed manual and multi-mode DCCD with mechanical and electronic centre locking, a helical front LSD and a TORSEN rear. Subaru's press kit is the main OEM source here; no ECM pinout source was found.
Factory ECU
The VA STI ECM is a later 32-bit Subaru unit managing Dual AVCS, DBW with SI-DRIVE maps and CAN communication with the chassis. Reflash dominates. Standalone conversions must preserve CAN data for the cluster, VDC and DCCD.
Factory ECU: harness cross-reference
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Subaru 22765-series 'Unit-EGI Control'
- Applies to
- MY11-14 GE/GH WRX & STI; MY11-15 GV/GR WRX (excl 2013); MY15-19 VA STI; ADM; manual
- Not for
- not non-ADM markets; not automatic; not 2013 GV/GR WRX (per Haltech)
Part numbers are USDM dealer-catalogue examples (2011 / 2014 / 2015 WRX-STI); ADM numbers not found. Supplier (Denso) not confirmed by a source.
- ECU family
- Subaru GR/GV/VA WRX STI ECM
- Applies to
- 2011-2021 WRX STI, 6MT; USDM
- Not for
- non-USDM STI see BF29149-S3
Examples: 22765AF180/181 -> AF182 (2013 STI), AF750 -> AF751 (2014 STI); 2010 STI 22765AA941 also listed. Other years not looked up.
- ECU family
- Subaru GR/GV/VA WRX STI ECM (non-USDM)
- Applies to
- 2008-2021 WRX STI non-USDM (JDM/EDM/ADM), manual
- Not for
- USDM STI see BF29115-S3
Non-USDM numbers not available from US dealer catalogues. For reference USDM 2008-09 STI = 22611AN350/AN351 ().
Factory ECU pinout: pending
No OEM pin table is in our library yet for the EJ257 (STI) factory ECU. No OEM-grade source found. Required: Subaru 2015-2021 WRX STI service manual (STIS), 'Engine Control Module (ECM) I/O signal' table for the EJ257, with the wiring diagram for connector and wire-colour data. Until then, wire from the harness maker's instructions or the factory service manual.
Factory ECU pinout
No OEM-grade source found. Required: Subaru 2015-2021 WRX STI service manual (STIS), 'Engine Control Module (ECM) I/O signal' table for the EJ257, with the wiring diagram for connector and wire-colour data.
Plug-and-play harness
A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
| Subaru WRX / STI MY11-19 (ADM only)HT-186300 | MY11-14 GE/GH WRX & STI; MY11-15 GV/GR WRX (excl 2013); MY15-19 VA STI; ADM; manual | $535Lowest | Maker ↗ | |
![]() | Manual 2011 - 2021 Subaru STIBF29115-S3 | 2011-2021 WRX STI, 6MT; USDM | $840 | Maker ↗ |
![]() | Manual 2008 - 2021 Subaru STI NON-USDMBF29149-S3 | 2008-2021 WRX STI non-USDM (JDM/EDM/ADM), manual | $840 | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |
Nexus S3 Plug n Play Adapter Harness Subaru WRX / STI MY11-19 (ADM only)
- Plugs into
Subaru engine control module (ADM WRX/STI MY11-19, EJ25/EJ20 DBW) · 22765AD030, 22765AF741…
- OEM part numbers
- 22765AD030, 22765AF741, 22765AG233
- ECU
- Subaru 22765-series 'Unit-EGI Control'
- Confidence
- low
Part numbers are USDM dealer-catalogue examples (2011 / 2014 / 2015 WRX-STI); ADM numbers not found. Supplier (Denso) not confirmed by a source.
Sources: E-1446
- Fits
- MY11-14 GE/GH WRX & STI; MY11-15 GV/GR WRX (excl 2013); MY15-19 VA STI; ADM; manual
- Exclusions
- not non-ADM markets; not automatic; not 2013 GV/GR WRX (per Haltech)
- SKU
- HT-186300
- Maker fitment
- Subaru WRX GE/GH MY11-14, WRX GV/GR MY11-15 (excl 2013), STI GE/GH MY11-14 and STI VA MY15-19; Australian-delivered only; manual only
- Maker notes
- kit with ECU HT-213312; ADM MY11-14 WRX only

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2011 - 2021 Subaru STI
- Plugs into
Subaru ECM (EJ257, 2011-21 WRX STI, GR/GV/VA) · 22765AF180, 22765AF181…
- OEM part numbers
- 22765AF180, 22765AF181, 22765AF182, 22765AF750, 22765AF751
- ECU
- Subaru GR/GV/VA WRX STI ECM
- Confidence
- medium
Examples: 22765AF180/181 -> AF182 (2013 STI), AF750 -> AF751 (2014 STI); 2010 STI 22765AA941 also listed. Other years not looked up.
Sources: E-1491
- Fits
- 2011-2021 WRX STI, 6MT; USDM
- Exclusions
- non-USDM STI see BF29149-S3
- SKU
- BF29115-S3
- Maker fitment
- Subaru STI (Manual); selector years 2011-2021; SKU label: Manual 2011 - 2021 Subaru STI
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 2011-14

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2008 - 2021 Subaru STI NON-USDM
- Plugs into
Subaru ECM (EJ257, 2008-21 WRX STI, non-USDM)
- ECU
- Subaru GR/GV/VA WRX STI ECM (non-USDM)
- Confidence
- low
Non-USDM numbers not available from US dealer catalogues. For reference USDM 2008-09 STI = 22611AN350/AN351 (E-1491).
- Fits
- 2008-2021 WRX STI non-USDM (JDM/EDM/ADM), manual
- Exclusions
- USDM STI see BF29115-S3
- SKU
- BF29149-S3
- Maker fitment
- Subaru STI; Subaru STI NON-USDM (Manual); selector years 2008-2021; SKU label: Manual 2008 - 2021 Subaru STI NON-USDM
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); non-USDM 2008+
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the WRX STI VA
Planned with the same rules as the configurator for this car's 4 cyl · port injection · drive-by-wire. The factory ECU is unplugged and replaced; nothing is written to it.
- Price TBA
ECU2Engine controller
4 cyl · port injection · drive-by-wire
Full sequential fuel and spark for this 4-cylinder, and its electronic throttle, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- Drive-by-wire built inFour half-bridges run up to two electronic throttles, with pedal and throttle sensors on the ECU's own inputs and a windowed watchdog that cuts the motors in hardware on a fault.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harness1 listed · from $535 USD listHT-186300
- Factory-connector → S3 adapter2 listed · from $840 USD list
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
How GAINS approaches the WRX STI VA
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3Cam phasing (VVT)gated
Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.
- 4Boost controlgated
A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.
- 5Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 6Factory load sensingfactory reference
What the factory ECU measures load with: MAF (hot-wire / hot-film) (medium confidence)
- 7Wideband sensorhardware
the factory sensor is already an A/F type; for tuning, fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller (factory A/F sensors are not LSU-compatible)
- 8Bottom end and head sealingfactory reference
Reported: MotoIQ: brittle hypereutectic ring lands with high top ring are the first failure even with mild detonation; case flex, head gaskets and rod bearing starvation above ~7,500 rpm also cited. (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
Drivetrain
- Multi-Mode DCCD: planetary centre diff, nominal 41:59 split, mechanical LSD plus electronically controlled lock
- Auto, Auto+, Auto- and six manual levels
Chassis integration
Tuning notes
Semi-closed deck block with reinforcing ribs, high-strength cast pistons, nitride-hardened crankshaft
Sourced3Even with the reinforced block, the VA EJ257 still uses cast pistons. Conservative knock margins, accurate fuelling and oil management on track are the main defences against ringland and bearing failures.
GAINS on the WRX STI VA
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Frequently asked
What engine is in the 2015-2021 WRX STI?
The 2.5 litre EJ257 turbo boxer with Dual AVCS (export markets). Japan used the 2.0 litre EJ207.34
What differential does the VA STI use?
A Multi-Mode DCCD planetary centre differential (41:59 nominal, mechanical plus electronic locking), a helical front LSD and a TORSEN rear LSD.3
How much boost does a stock 2015 STI run?
Subaru quotes a maximum of 14.7 psi.3
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- 40 CFR 86.1806-04 On-board diagnostics (2012 edition) · US Government Publishing Office · oem · retrieved 2026-10-25
- Top Ten Engines - #8 Subaru EJ257 · DSPORT Magazine · press · retrieved 2026-10-25
- 2015 Subaru WRX STI Press Kit · Subaru of America · oem · retrieved 2026-10-25
- Subaru WRX · Wikipedia · community · retrieved 2026-10-25
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-907 Haltech usage policy (sourced, high confidence)
- E-909 Haltech S3 adapter harness page (sourced, high confidence)
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)
- E-1446 Subaru 2011-15 ECU (supported, medium confidence)
- E-1491 harness ECU xref: Subaru Impreza WRX/STI ECMs (USDM) (verified, high confidence)


