United States · 1966-1977 · Ford (in-house) instruments

Ford Bronco (first generation) gauges

One round cluster housingShared with 1961-66 F-SeriesCable speedometerThermal fuel and temp on a voltage regulator73-10 ohm fuel senderNo factory tach

Early Bronco gauges sit in one round cluster housing: a center speedometer with four small dials around it for fuel, temperature, oil pressure and charging. Ford shared this cluster with 1961-66 F-Series trucks. The fuel and temperature dials are thermal gauges on a constant voltage regulator, the speedometer is cable driven, and there was no factory tachometer.Medium123

0 gauges ·

A Round Gauge kit for the Ford Bronco (first generation)

Built from the factory gauge sizes below: one digital gauge per hole.

None of the current Round Gauge sizes matches this dash yet. We size new gauges from the most-requested cars.

Factory gauges

5 round instruments in the factory dash

InstrumentOriginal sizeHow it worksRound Gauge
Speedometer and odometer (center of the cluster)Not published; the whole cluster sits in one round dash openingLow12Cable drive— No size yetThe speedometer is not a separate round hole; it shares one housing with the four minor dials. No Round Gauge size replaces the cluster without a new panel, and we have not measured the opening.
Fuel level (minor dial in the cluster)Not publishedLow13Thermal (bimetal)— No size yetMinor dial inside the one-piece cluster, fed by the constant voltage regulator.
Water temperature (minor dial in the cluster)Not publishedLow13Thermal (bimetal)— No size yetMinor dial inside the one-piece cluster, fed by the constant voltage regulator.
Oil pressure (minor dial in the cluster)Not publishedLow1Other— No size yetElectric dial inside the cluster. Some related F-Series clusters had only fuel and temperature dials, so check what your cluster carries.
Ammeter (minor dial in the cluster)Not publishedLow1Other— No size yetCharging dial inside the cluster. Owners ask whether some clusters used a voltmeter instead; our sources do not settle it.

Electrical facts for a gauge swap

Earth polarity, stabiliser, senders and signal types.

System voltage and earth12 V, negative earthStandard for Ford vehicles of this era; confirm the battery polarity on the vehicle before wiring anything.Researched, unverified2
Instrument voltage regulator

Constant voltage regulator on the back of the cluster, Ford B9MZ-10804-C (shared with 1957-66 trucks and 1960-66 cars)

Sourced · medium35
Regulated gauge voltage
  • Reduced from 12 V
  • One seller states about 6 V
Ford thermal regulators pulse the supply, so a meter shows an average. Only a seller listing gives a figure; we found no Ford document stating it.Researched, unverified5
Fuel sender

About 73 ohms empty, 10 ohms full (Ford standard to 1986), non-linear

The factory sender is non-linear, about 25 ohms at half by one gauge maker's figures; some aftermarket 73-10 senders are linear and read wrong mid-tank.Sourced · medium8910
Speedometer drive
  • Cable from a driven gear16-21 tooth range listed
  • OE-type cable 72.5 in1,842 mm
Sourced · medium2
TachometerNone from the factoryReplacement and aftermarket tachs read the coil negative terminal.Low confidence26

The factory dash

The 1966-77 Bronco uses a single round instrument cluster in a flat steel dash.

Early Bronco gauges are grouped inside it: the speedometer in the middle and four small dials around it.Low1

Owners note that the same round cluster appears in 1961-66 F100 and F-1100 trucks. Some of those truck clusters had all four minor dials and some had only fuel and temperature, so a used cluster may not match your Bronco.Low1

Separate holes in the dash trim, such as the one owners measure at 1-5/8 in (41 mm), take switches and accessories, not instruments.Low7

How the original instruments work

The fuel and temperature dials are thermal gauges.

A constant voltage regulator on the back of the cluster pulses their supply so the needles stay steady as system voltage moves.Medium35

The fuel sender follows the Ford range of roughly 73 ohms empty to 10 ohms full. The original sender is non-linear, so the gauge expects a low reading at half tank.Medium810

The speedometer runs from a cable and a driven gear. Gear tooth count is chosen for tire size and axle ratio, so changing either changes the reading.Medium2

What owners replace and why

The voltage regulator is the usual first replacement.

A failed unit sends full voltage to the gauges, and all of them read full.Low5

Owners who lift the truck or change tires replace the speedometer driven gear. Bigger engines and swaps lead many to add a tachometer, which the factory never fitted.Low2

Complete reproduction and aftermarket clusters are sold to fit the stock opening with the factory holes, including OE-look faces with a tachometer added.Medium46

Going digital without losing the look

Because the cluster is one housing, individual round gauges need a new panel or insert behind the bezel.

Keep the original cluster and bezel boxed so the truck can go back to stock.Low14

A digital speedometer can read a GPS module or an electronic sender in place of the cable. The tachometer signal comes from the coil negative terminal on points or stock electronic ignition.Low6

Keeping the factory fuel sender works if the new gauge accepts the Ford 73-10 ohm non-linear curve. Disconnect the battery before working behind the dash.Medium109

Common faults with the original gauges

  1. 1Fuel and temperature gauges both read full

    Usual cause

    Failed constant voltage regulator passing full battery voltage

    Fix

    Replace the regulator on the back of the cluster; check its earth to the cluster housing.Low5

  2. 2Fuel gauge reads wrong at half tank but right at full and empty

    Usual cause

    Linear aftermarket 73-10 ohm sender on a gauge built for Ford's non-linear sender

    Fix

    Fit a sender with the factory non-linear curve, or a gauge that can be calibrated to the sender.Medium910

  3. 3Speedometer reads low after a lift and bigger tires

    Usual cause

    Driven gear no longer matches tire size and axle ratio

    Fix

    Fit the driven gear tooth count that suits the new tire and ratio, or recalibrate an electronic speedometer.Medium2

  4. 4Speedometer needle bounces or the cable howls

    Usual cause

    Dry or kinked speedometer cable

    Fix

    Replace or lubricate the cable and route it without tight bends; extended cables suit relocated transfer cases.Low2

Restoration tips

Keep it original and reversible

  • Check the cluster's minor dials before buying a used one; truck clusters may lack the oil and charge dials.Low1
  • Keep the original cluster, regulator and bezel, and use the factory holes so any change is reversible.Low4
  • Record the speedometer driven gear tooth count before removing it.Low2

Frequently asked

What gauges came in a 1966-77 Bronco?

The early Bronco has a speedometer with odometer in the center of one round cluster and four small dials around it: fuel, water temperature, oil pressure and an ammeter. There was no factory tachometer. The same cluster family was used in 1961-66 F-Series trucks, where some versions had only fuel and temperature dials.Low1

Why do all my early Bronco gauges read full?

The most common cause is a failed constant voltage regulator on the back of the cluster. When it fails it can pass full battery voltage to the thermal gauges, and they read full. Replace the regulator and check its earth path to the cluster before suspecting the senders.Low53

What ohm fuel sender does an early Bronco use?

It uses the Ford range of about 73 ohms empty and 10 ohms full, which Ford used up to 1986. The original sender is non-linear, reading near 25 ohms at half by one gauge maker's figures. A linear aftermarket sender with the same end values can read wrong in the middle of the tank.Medium8109

Is the early Bronco speedometer cable driven?

Yes. A cable runs from a driven gear to the back of the speedometer. Sellers list driven gears in a 16 to 21 tooth range and an OE-type cable of 72.5 in (1,842 mm). Tire size and axle ratio set the gear needed, so a lift and bigger tires usually call for a new gear.Medium2

Can I fit round digital gauges in an early Bronco dash?

Not straight into the factory opening, because it holds one cluster rather than separate round holes. You need a panel or insert sized for the gauges you choose. Measure the opening on your truck first, and keep the original cluster so the change can be reversed.Low14

Related cars

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

10 sources
  1. Gauge cluster thread (early Bronco and 1961-66 F-Series round cluster) · Ford-Trucks.com forum · community · retrieved 2026-11-04
  2. Early Bronco stock dash instrument cluster and gauges · Wild Horses 4x4 · vendor-doc · retrieved 2026-11-04
  3. Instrument cluster voltage regulator B9MZ-10804-C, 1957-66 Ford truck, 1966-77 Bronco, 1960-66 Ford car · Dennis Carpenter · vendor-doc · retrieved 2026-11-04
  4. OE style gauge cluster, 1966-77 Ford Bronco · Dennis Carpenter · vendor-doc · retrieved 2026-11-04
  5. 1966-1977 Ford Bronco constant voltage regulator · Bronco Graveyard · vendor-doc · retrieved 2026-11-04
  6. Classic Instruments 66-77 Ford Bronco gauge set · JBS Power Centre · vendor-doc · retrieved 2026-11-04
  7. Searching for voltmeter to fit 1-5/8 hole in dash trim piece · ClassicBroncos forum · community · retrieved 2026-11-04
  8. Fuel sending units · Fordification · community · retrieved 2026-11-04
  9. 73-10 ohm fuel sender (non-linear vs linear note) · Pegasus Auto Racing · vendor-doc · retrieved 2026-11-04
  10. My 73-10 ohm fuel gauge isn't working properly with my replacement sender · AutoMeter · vendor-doc · retrieved 2026-11-04

Markets: USA, Canada, Australia (import scene), Europe (import scene). Make and model names identify the vehicle only; GAINS is not affiliated with the vehicle or instrument makers.