United States · 1967-1972 · Ford (in-house) instruments

Ford F-100 and F-Series pickup (fifth generation, 'bumpside') gauges

Center speedo, four small dialsGauges or warning lights by truckThermal fuel and tempFord 73-10 ohm fuel senderCable speedometerNo factory tach

1967-72 F100 gauges are round: a center speedometer with two small dials stacked on each side, fuel and temperature on the left and ammeter and oil pressure on the right. Some trucks used warning lights in place of the oil and charge dials. Fuel and temperature are thermal gauges on Ford's instrument voltage regulator, and the speedometer is cable driven.Low12

5 gauges · 86 mm + 52 mm

A Round Gauge kit for the Ford F-100 and F-Series pickup (fifth generation, 'bumpside')

Built from the factory gauge sizes below: one digital gauge per hole.

Factory gauges

5 round instruments in the factory dash

InstrumentOriginal sizeHow it worksRound Gauge
Speedometer and odometer (center)Large center dial; factory diameter not publishedLow13Cable drive86 mm To measureAftermarket bezels for this truck place a 3-3/8 in (85.7 mm) speedometer in the center. That is a bezel size, not a measured factory dial.
Fuel level (left, upper)Small dial; factory diameter not publishedLow13Thermal (bimetal)52 mm To measureAftermarket bezels use 2-1/16 in (52.4 mm) holes for the four minor gauges.
Water temperature (left, lower)Small dial; factory diameter not publishedLow13Thermal (bimetal)52 mm To measure
Ammeter (right, upper; warning light on some trucks)Small dial; factory diameter not publishedLow14Other52 mm To measure
Oil pressure (right, lower; warning light on some trucks)Small dial; factory diameter not publishedLow12Thermal (bimetal)52 mm To measureThe C9AZ regulator listing says it feeds the oil gauge as well as fuel and temperature.

Electrical facts for a gauge swap

Earth polarity, stabiliser, senders and signal types.

System voltage and earth12 V, negative earthStandard for Ford trucks of this era; confirm on the truck.Researched, unverified2
Instrument voltage regulator
  • Ford C9AZ-10804-A, listed for 1970 Ford trucks and 1969-79 Ford cars
  • Controls the fuel, temperature and oil gauges
Check the correct regulator for 1967-69 and 1971-72 trucks by part number.Sourced · medium2
Fuel sender

About 73 ohms empty, 10 ohms full (Ford standard to 1986), non-linear

Sourced · medium67
Speedometer driveMechanical cableSourced · medium5
Retrofit sensors

Electronic retrofit systems supply their own oil pressure, coolant temperature and speed sensors and reuse the stock gauge bezel

Sourced · medium5

The factory dash

Owners describe the 1967-72 F-Series cluster as a center speedometer with two small round dials stacked on each side.

Fuel and water temperature sit on the left, ammeter and oil pressure on the right.Low1

Not every truck had all four dials. Some used warning lights for oil and charging, so check a used cluster before you buy it.Low1

Openings to the left and right of the main cluster take larger accessories in some dashes. There was no factory tachometer in the cluster.Low13

How the original instruments work

The fuel, temperature and oil dials are thermal gauges fed through an instrument voltage regulator.

It pulses the supply so readings hold steady as system voltage changes.Medium2

The fuel sender follows Ford's 73 ohms empty to 10 ohms full range with a non-linear curve. The speedometer runs from a cable.Medium675

What owners replace and why

Owners replace the regulator, ammeter and individual gauges, which are sold separately for these trucks.

Many convert to a bezel that adds a tachometer and full gauges.Medium43

Aftermarket bezels for this dash use one or two 3-3/8 in (86 mm) holes for speedometer and tach plus four 2-1/16 in (52 mm) holes for the minor gauges.Medium3

Going digital without losing the look

Retrofit systems reuse the stock plastic or metal bezel, which keeps the dash looking original.

Keep the factory cluster boxed for a reversible change.Medium5

A digital speedometer can read a GPS module or an electronic speed sender instead of the cable. The tachometer reads the coil negative terminal on stock ignition.Low5

Keeping the factory fuel sender works if the gauge accepts Ford's 73-10 ohm curve. Disconnect the battery before working behind the dash, and fuse any new feed.Medium7

Common faults with the original gauges

  1. 1Fuel, temperature and oil gauges read high together

    Usual cause

    Failed instrument voltage regulator

    Fix

    Replace the regulator with the correct part for the year.Medium2

  2. 2Fuel gauge wrong at mid-tank

    Usual cause

    Linear aftermarket sender on a gauge built for Ford's non-linear sender

    Fix

    Fit a sender with the factory curve or a calibratable gauge.Medium7

  3. 3Used cluster has warning lights where the truck had gauges

    Usual cause

    Both gauge and warning-light clusters were built

    Fix

    Match the cluster type to the truck's wiring before buying.Low1

Restoration tips

Keep it original and reversible

  • Note whether your truck has gauges or warning lights for oil and charging before ordering parts.Low1
  • Choose a retrofit that keeps the factory bezel so the dash stays original-looking and reversible.Medium5
  • Keep the original regulator and cluster with the truck's records.Low2

Frequently asked

What gauges are in a 1967-72 Ford F100?

The cluster has a center speedometer with two small dials on each side: fuel and water temperature on the left, ammeter and oil pressure on the right, by owner accounts. Some trucks used warning lights instead of the oil and charge dials. There was no factory tachometer in the cluster.Low1

Why do my F100 fuel and temp gauges both read high?

When several thermal gauges read high together, the instrument voltage regulator is the usual cause. It feeds the fuel, temperature and oil gauges. Replace it with the correct part for the year, then check the cluster earth if readings are still off.Medium2

What fuel sender does a 1967-72 F100 use?

It uses Ford's range of about 73 ohms empty and 10 ohms full, which Ford kept until 1986. The original curve is non-linear. A linear aftermarket sender with the same end values can read wrong in the middle of the tank, so check before you buy.Medium67

What size gauges fit a 1967-72 F100 dash?

Aftermarket bezels for this truck use 3-3/8 in (86 mm) holes for the speedometer and tachometer and 2-1/16 in (52 mm) holes for the four minor gauges. The factory dials themselves have no published diameter, so measure your cluster before planning a direct swap.Medium3

Related cars

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Need help: identify an instrument cluster for 1967 F100 · Fordification forum · community · retrieved 2026-11-04
  2. Instrument cluster voltage regulator C9AZ-10804-A, 1970 Ford truck, 1969-79 Ford car · Dennis Carpenter · vendor-doc · retrieved 2026-11-04
  3. Classic Dash instrument bezel, 5 hole, F-100 1967-1972 · CJ Pony Parts · vendor-doc · retrieved 2026-11-04
  4. Amp gauge, F-100 1967-1972 · CJ Pony Parts · vendor-doc · retrieved 2026-11-04
  5. Dakota Digital MTX instrument system for Ford trucks 1967-1972 · Vivid Racing · vendor-doc · retrieved 2026-11-04
  6. Fuel sending units · Fordification · community · retrieved 2026-11-04
  7. 73-10 ohm fuel sender (non-linear vs linear note) · Pegasus Auto Racing · vendor-doc · retrieved 2026-11-04

Markets: USA, Canada, Australia (import scene), Europe (import scene). Make and model names identify the vehicle only; GAINS is not affiliated with the vehicle or instrument makers.