BMW · 2001–2006

M3 E46: every channel it can give you

No public data maps this car's chassis channels yet. 18 more chassis and driver channels are on the car, waiting for GAINS discovery. Plus 25 Hz GPS and a motion sensor in the dongle itself.

K-line (ISO 9141 / KWP2000)Stability control: Standard (DSC)Manual / SMGS54 3.2 I6
23channels
5 Standard OBD2
18 To discover
6 Built into the dongle
OBD-II portK-line (ISO 9141 / KWP2000)Engine data over standard OBD2
Internal CAN busYesWhere the chassis modules talk
GatewayNo CAN at the portBetween the car's bus and the port
Stability control · ABSStandard (DSC)ABS: Standard

Channels

Every channel the E46 is expected to give, by group. Filter by how it arrives.

Driver inputs

Steering angle To discoverstability control (DSC)
Throttle position Standard OBD2
Brake pressure To discoverstability control (DSC)
Brake pedal switch To discoverbrake lights
Clutch pedal To discovermanual gearbox · if fitted
Gear To discovergearbox

Wheels and chassis

Wheel speed, front left To discoverABS
Wheel speed, front right To discoverABS
Wheel speed, rear left To discoverABS
Wheel speed, rear right To discoverABS
Vehicle speed Standard OBD2
Yaw rate To discoverstability control (DSC)
Lateral g To discoverstability control (DSC)
Longitudinal g To discoverstability control (DSC) · if fitted

Engine

Engine RPM Standard OBD2
Intake air temperature Standard OBD2

Temperatures and pressures

Oil temperature To discoverengine (if the car measures it) · if fitted
Oil pressure To discoverengine (if the car measures it) · if fitted
Coolant temperature Standard OBD2
Gearbox temperature To discoverautomatic / dual-clutch gearbox · if fitted

Stability systems

ABS active To discoverABS
Traction control active To discoverstability control (DSC)
Stability control active To discoverstability control (DSC)

Built into the dongle, on every car

GPS speed and position 25 Hz
Lap, sector and delta times computed
Lateral and longitudinal g motion sensor
Yaw rate motion sensor
Heading and altitude GPS
Combined g (friction circle) computed

How the data gets out

Where the E46's sensors live and how GAINS reaches them.

Car's internal CAN busEngineDSCSteeringDashK-lineCAN tap leadOBD-II · K-lineTelemetry Dongle Pro plugs into the OBD-II port

Wired connection to the car's CAN bus

This car's OBD-II port uses an older protocol for engine data, but the stability-control, ABS and dash modules talk on an internal CAN bus. A two-wire connection to that bus lets discovery read the chassis sensors.

Telemetry Dongle Pro (engine data) · CAN tap lead for chassis data (accessory, coming later)

Discovery on your M3

The 18 channels marked “To discover” are learned once, from your car, then added for every E46 owner.

  1. Plug in and identify

    The dongle finds the bus speed by listening only, reads the VIN and matches the car's data pattern to our database.

    about 1 min
  2. Guided steps, parked

    The app walks you through each control for a few seconds: wheel lock to lock, brake light then firm, throttle (engine off), clutch, every gear, handbrake, stability-control button. The dongle records what changes on the car's data stream.

    about 5 min
  3. Module read

    With the car parked, the dongle asks each module (ABS, gearbox, body) which values it can report. Read-only requests: nothing is written or changed.

    about 5–10 min, automatic
  4. Short drive

    A normal drive with a few stops, steady speeds and turns. The dongle matches unknown values against its 25 Hz GPS and motion sensor to find wheel speeds, yaw rate and g-forces.

    10–15 min
  5. Results

    Matched channels appear in the app. Anything that needs a closer look is checked by us and added later; you get a notification, and every owner of the same car gets the channel too.

    most right after the drive

First time: about 25–30 minutes, once per car. Times are estimates until measured on real cars. Discovery only listens and reads: it never writes to the car, clears codes or bypasses security.

FAQ

Can I log steering angle and brake pressure on a M3 E46 through the OBD-II port?

The E46 is expected to carry them (stability control (DSC)), but no public data maps them yet. GAINS discovery learns them from a capture of your car: wired connection to the car's can bus. A standard OBD2 scan tool won't show them.

What OBD-II protocol does the M3 E46 use?

K-line (ISO 9141 / KWP2000). Its engine, stability and dash modules also share an internal CAN bus.

How long does discovery take on a E46?

The first time, about 25–30 minutes, once per car (estimate): guided steps while parked, a read-only module check and a short drive. After that the dongle recognises the car when you plug in.

Channel lists combine public vehicle data from the open-source community with the equipment this generation is known to carry. “Expected” and “To discover” channels are not yet confirmed by our own logs, and equipment varies by market, trim and year. Vehicle names identify the cars only; GAINS is not affiliated with BMW. Specifications are pre-release and may change before launch.