Honda · 1996-00

Honda Civic EK EX / Si (D16Y8 / B16A2) ECU and tuning guide

The Honda Civic EK EX / Si (D16Y8 / B16A2) (1996-00) runs the D16Y8 / D16Z6 / D15: 1.6 L I4, naturally aspirated, port injection, cable throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Factory ECU, pinout and chassis research on this page is shared with Honda Civic Type R EK9 B16B.

Honda Civic EK EX / Si (D16Y8 / B16A2), side view
Studio render for illustration, not a photograph of a specific car.
Years1988-00
Displacement1.6L
LayoutI4
InductionNaturally aspirated
InjectionPort injection
Cam controlVTECD16Z6/Y8
IgnitionDistributor
Swap demandMedium

Part of the Honda D-series family. B / K-swap chassis

Modeled power and torque

Modelled estimate, not a dyno result.

D16Y8 / D16Z6 / D15: stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
0501001502002500501001502001k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (127 hp at 6600 rpm, 107 lb-ft at 5500 rpm); the curve shape between peaks is modeled. Intake + exhaust + tune (pump fuel): Typical NA gains come mostly above mid-rpm.

D16Y8 / D16Z6 / D15 data

Platform background

The sixth-generation Civic (EK) is OBD2: OBD2a for 1996-98 and OBD2b for 1999-2000. The 1999-2000 US Civic Si got the 160 hp B16A2, and the Japanese EK9 Type R used the B16B. Many EK builds convert to OBD1 ECUs using jumper harnesses. K-swaps need an EG/DC2-style subframe for the Hasport EKK mounts.

Factory ECU

OBD-II

OBD-II diagnostics (California required OBD II on essentially all 1996-and-later passenger cars)

Sourced1
OBD2 sub-generationsOBD2a (1996-98) and OBD2b1999-2000Low confidence6
1999-2000 Si engineB16A2, 1.6 L DOHC VTEC, 160 hp, 111 lb-ftSourced4
EK9 Type R engineB16B, 10.8:1Low confidence6
OBD1 conversion

OBD2A-to-OBD1 jumper harnesses allow a 1992-95 manual-transmission ECU in a 1996-98 chassis

Sourced · medium5

The jumper harnesses referenced here are listed for 1996-98 (OBD2a) chassis; confirm compatibility separately for 1999-2000 (OBD2b) cars. Converting to OBD1 gives up OBD2 readiness monitoring, so check local inspection requirements first.

Factory ECU: harness cross-reference

From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.

Honda OBD2a ECU (1996-98 Civic/Integra/Accord/Prelude)Part numbers not yet sourced.
ECU family
Honda OBD2
Applies to
Label 1996-99, selector 1996-2001; manual
Not for
OBD2a vs OBD2b connector split around 1998-99 - confirm

Label (1996-99) and selector years (1996-2001) disagree; may straddle OBD2a/OBD2b. No numbers verified.

Low confidenceUnverified
Honda OBD2b ECU (1999-2001 Civic/Integra/Accord)
37820-P2P-A1237820-P2P-A11
ECU family
Honda OBD2
Applies to
Label 2000-01, selector 1998-2002; manual; 37820-P2P-A12 = 1999-2000 Civic 4-door non-VTEC-E

Part numbers are examples for one Civic variant only (dealer catalogue snippet); Integra/Accord codes not verified.

Low confidenceUnverifiedE-1461

Factory ECU pinout

Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.

Honda Civic EK OBD2a ECM/PCM ('96-98)

The 1996-98 US-market Civic (EK) ECM/PCM uses four Honda connectors: A (32P), B (25P, automatic PCM only), C (31P) and D (16P). Honda's service manual prints one shared table for '96-98 D16Y5, D16Y7 and D16Y8 cars and the '99-00 D16Y5 with manual gearbox. 84 terminals are assigned across 104 cavities, with variant footnotes.

1996-1998 (and 1999-2000 D16Y5 M/T) · USA and Canada (Honda U.S. service manual); Canadian KL models called out in footnotes · 4 connectors, 104 cavities · 84 terminals sourced

ECM/PCM connector A (32P)32 cavities · 28 terminals listed · 32-cavity three-row plug as drawn by Honda: 28 numbered terminals plus 4 cavities drawn crossed out (no terminal); terminals 10, 11, 23, 24 and blank 32 are double-width cells.

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedHonda draws every ECM/PCM face as 'Wire side of female terminals': the harness plug seen from the wire-entry side, with a raised box drawn along the top edge. That has the same left-right orientation as looking straight into the ECU header, so the cells are stored exactly as drawn (ecu-side); the harness plug's mating face is the mirror image.
Honda Civic EK OBD2a ECM/PCM ('96-98): ECM/PCM connector A (32P)Raised box over cavities as drawn (latch side)1: No. 4 fuel injector (INJ4)12: No. 3 fuel injector (INJ3)23: No. 2 fuel injector (INJ2)34: No. 1 fuel injector (INJ1)45: Secondary heated oxygen sensor heater control (SO2SHTC)56: Primary heated oxygen sensor heater control (PO2SHTC)67: EGR control solenoid valve (ESOL) or EGR valve (E-EGR)78: VTEC solenoid valve (VTS)89: Logic ground (LG1)910: Power ground (PG1)1011: Power source (IGP1)1112: Idle air control valve (IACV)1213: Idle air control valve negative side (IACV N)1314: Idle air control valve positive side (IACV P)1415: EVAP purge control solenoid valve (PCS)1516: Fuel pump relay (FLR)1617: A/C clutch relay (ACC)1718: Malfunction indicator lamp (MIL)1819: Alternator control (ALTC)1920: Ignition control module (ICM)20Cavity with no terminal number22: Logic ground (LG2)2223: Power ground (PG2)2324: Power source (IGP2)2425: Reference voltage to the TCM (VREF)25Cavity with no terminal number27: Radiator fan control (FANC)2728: EVAP bypass solenoid valve (2WBS)2829: EVAP control canister vent shut valve (VSV)2930: Interlock control unit signal (SLU)30Cavity with no terminal numberCavity with no terminal number
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1No. 4 fuel injector (INJ4)injector drive, duty controlledYEL
2No. 3 fuel injector (INJ3)injector drive, duty controlledBLU
3No. 2 fuel injector (INJ2)injector drive, duty controlledRED
4No. 1 fuel injector (INJ1)injector drive, duty controlledBRN
5Secondary heated oxygen sensor heater control (SO2SHTC)heater drive: battery voltage with ignition ON, duty controlled when warmBLK/WHT
6Primary heated oxygen sensor heater control (PO2SHTC)heater drive: battery voltage with ignition ON, duty controlled when warmBLK/WHT
7EGR control solenoid valve (ESOL) or EGR valve (E-EGR)duty controlled while EGR operates, 0 V otherwiseRED / PNKVariant: ESOL, RED wire, on CVT D16Y5 (footnote *3); E-EGR, PNK wire, on M/T D16Y5 (footnote *10).
8VTEC solenoid valve (VTS)0 V at low engine speed, battery voltage at high engine speedGRN/YELD16Y5 and D16Y8 engines only (footnote *12).
9Logic ground (LG1)< 1.0 V at all timesBRN/BLK
10Power ground (PG1)< 1.0 V at all timesBLK
11Power source (IGP1)battery voltage with ignition ON (II)YEL/BLK
12Idle air control valve (IACV)duty controlled with engine runningBLK/BLUExcept A/T and D16Y7 engine (footnote *5).
13Idle air control valve negative side (IACV N)duty controlled with engine runningORNA/T and D16Y7 engine (footnote *4).
14Idle air control valve positive side (IACV P)duty controlled with engine runningBLK/BLUA/T and D16Y7 engine (footnote *4).
15EVAP purge control solenoid valve (PCS)battery voltage below 154 F (68 C) coolant, duty controlled aboveRED/YEL
16Fuel pump relay (FLR)0 V for 2 s after ignition ON, then battery voltageGRN/YEL
17A/C clutch relay (ACC)0 V with compressor ON, battery voltage OFFBLK/RED
18Malfunction indicator lamp (MIL)0 V with MIL ON, battery voltage OFFGRN/ORN
19Alternator control (ALTC)battery voltage warm running, 0 V under small electrical loadWHT/GRNUSA model (footnote *1).
20Ignition control module (ICM)ignition pulse to the ICM: battery voltage with ignition ON, about 10 V runningYEL/GRN
22Logic ground (LG2)< 1.0 V at all timesBRN/BLK
23Power ground (PG2)< 1.0 V at all timesBLK
24Power source (IGP2)battery voltage with ignition ON (II)YEL/BLK
25Reference voltage to the TCM (VREF)about 5 V with ignition ONWHT/REDA/T D16Y8 engine (footnote *6).
27Radiator fan control (FANC)0 V with fan running, battery voltage stoppedGRNUSA model (footnote *1).
28EVAP bypass solenoid valve (2WBS)battery voltage with ignition ONBLUFitted per Honda footnote *8: '96 D16Y8 (coupe), '97 D16Y8 (coupe all models, sedan KL model), '98 D16Y5, '98 D16Y8, '99-00 D16Y5 M/T and footnote *15: '97 D16Y7 (coupe KL model, sedan KL (LX) model), '98 D16Y7.
29EVAP control canister vent shut valve (VSV)battery voltage with ignition ONLT GRN/WHTFitted per Honda footnote *8: '96 D16Y8 (coupe), '97 D16Y8 (coupe all models, sedan KL model), '98 D16Y5, '98 D16Y8, '99-00 D16Y5 M/T and footnote *15: '97 D16Y7 (coupe KL model, sedan KL (LX) model), '98 D16Y7.
30Interlock control unit signal (SLU)battery voltage with ignition ON and brake pedal pressedWHT/REDCVT D16Y5 engine (footnote *3). Honda describes this as an input on this table.

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

PCM connector B (25P)25 cavities · 17 terminals listed · 25-cavity three-row plug as drawn by Honda: 17 numbered terminals plus 8 crossed-out cavities; the two left-hand columns are double-width cells. Used only on A/T D16Y7 and D16Y8 (PCM).

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedHonda draws every ECM/PCM face as 'Wire side of female terminals': the harness plug seen from the wire-entry side, with a raised box drawn along the top edge. That has the same left-right orientation as looking straight into the ECU header, so the cells are stored exactly as drawn (ecu-side); the harness plug's mating face is the mirror image.
Honda Civic EK OBD2a ECM/PCM ('96-98): PCM connector B (25P)Raised box over cavities as drawn (latch side)1: Linear solenoid valve minus side (LS-)12: Linear solenoid valve plus side (LS+)23: Shift control solenoid valve A (SHA)34: Lock-up control solenoid valve B (LC B)45: Lock-up control solenoid valve A (LC A)5Cavity with no terminal numberCavity with no terminal number8: A/T gear position switch D3 (ATPD3)8Cavity with no terminal numberCavity with no terminal number11: Shift control solenoid valve B (SHB)1112: Interlock control unit (SLU)1213: D4 indicator light (D4 IND)1314: Mainshaft speed sensor ground (NMSG)1415: Mainshaft speed sensor (NM)1516: A/T gear position switch R (ATPR)1617: A/T gear position switch 2 (ATP2)17Cavity with no terminal numberCavity with no terminal numberCavity with no terminal numberCavity with no terminal number22: Countershaft speed sensor ground (NCSG)2223: Countershaft speed sensor (NC)2324: A/T gear position switch D4 (ATPD4)2425: A/T gear position switch N/P (ATPNP)25
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Linear solenoid valve minus side (LS-)ground return for the linear solenoid: pulses with ignition ONWHTPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
2Linear solenoid valve plus side (LS+)drives the linear solenoid: pulses with ignition ONREDPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
3Shift control solenoid valve A (SHA)battery voltage in 2nd and 3rd, about 0 V in 1st and 4thBLU/YELPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
4Lock-up control solenoid valve B (LC B)battery voltage with lock-up ONGRN/BLKPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
5Lock-up control solenoid valve A (LC A)battery voltage with lock-up ONYELPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
8A/T gear position switch D3 (ATPD3)0 V in D3, battery voltage otherwisePNKPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
11Shift control solenoid valve B (SHB)battery voltage in 1st and 2nd, about 0 V in 3rd and 4thGRN/WHTPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
12Interlock control unit (SLU)0 V with ignition ON and brake pedal pressedWHT/REDPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
13D4 indicator light (D4 IND)battery voltage with D4 indicator ONGRN/BLKPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
14Mainshaft speed sensor ground (NMSG)sensor groundWHTPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
15Mainshaft speed sensor (NM)pulses with engine runningREDPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
16A/T gear position switch R (ATPR)0 V in R, battery voltage otherwiseWHTPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
17A/T gear position switch 2 (ATP2)0 V in 2, battery voltage otherwiseBLUPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
22Countershaft speed sensor ground (NCSG)sensor groundGRNPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
23Countershaft speed sensor (NC)pulses with ignition ON and front wheels turningBLUPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
24A/T gear position switch D4 (ATPD4)0 V in D4, 5 V otherwiseYELPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).
25A/T gear position switch N/P (ATPNP)0 V in N or P, battery voltage otherwiseLT GRNPCM connector B is used on A/T D16Y7 and D16Y8 only (table footnote *2).

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECM/PCM connector C (31P)31 cavities · 23 terminals listed · 31-cavity three-row plug as drawn by Honda: 23 numbered terminals plus 8 crossed-out cavities.

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedHonda draws every ECM/PCM face as 'Wire side of female terminals': the harness plug seen from the wire-entry side, with a raised box drawn along the top edge. That has the same left-right orientation as looking straight into the ECU header, so the cells are stored exactly as drawn (ecu-side); the harness plug's mating face is the mirror image.
Honda Civic EK OBD2a ECM/PCM ('96-98): ECM/PCM connector C (31P)Raised box over cavities as drawn (latch side)1: Crankshaft fluctuation sensor P side (CKFP)12: Crankshaft position sensor P side (CKPP)23: Top dead centre sensor P side (TDCP)34: Cylinder position sensor P side (CYPP)45: A/C switch signal (ACS)56: Starter switch signal (STS)67: Service check signal (SCS)78: K-line to data link connector (K-LINE)89: ECM to TCM data output (TMA)910: Voltage back up (VBU)1011: Crankshaft fluctuation sensor M side (CKFM)1112: Crankshaft position sensor M side (CKPM)1213: Top dead centre sensor M side (TDCM)1314: Cylinder position sensor M side (CYPM)1415: VTEC pressure switch (VTM)1516: Power steering oil pressure switch (PSPSW)1617: Alternator FR signal (ALTF)1718: Vehicle speed sensor (VSS)18Cavity with no terminal numberCavity with no terminal numberCavity with no terminal numberCavity with no terminal number23: Air/fuel ratio (HO2S) sensor pump cell + (IP+)2324: Air/fuel ratio (HO2S) sensor common (IP-, VS-)2425: Air/fuel ratio (HO2S) sensor VS cell voltage (VS+)25Cavity with no terminal numberCavity with no terminal numberCavity with no terminal number29: A/T gear position switch N/P (ATPNP) or clutch switch (CLSW)2930: TCM to ECM data input (TMB)30Cavity with no terminal number
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Crankshaft fluctuation sensor P side (CKFP)sensor + : pulses with engine runningBLU/RED
2Crankshaft position sensor P side (CKPP)sensor + : pulses with engine runningBLU
3Top dead centre sensor P side (TDCP)sensor + : pulses with engine runningGRN
4Cylinder position sensor P side (CYPP)sensor + : pulses with engine runningYEL
5A/C switch signal (ACS)0 V with A/C switch ON, battery voltage OFFBLU/RED
6Starter switch signal (STS)battery voltage while cranking (III)BLU/ORN
7Service check signal (SCS)0 V with service check connector jumped, about 5 V or battery voltage openBRN
8K-line to data link connector (K-LINE)OBD II scan tool serial line, about 5 V with ignition ONLT BLU
9ECM to TCM data output (TMA)pulses with ignition ONGRYCVT D16Y5 engine (footnote *3).
10Voltage back up (VBU)battery voltage at all times (DTC memory)WHT/BLU
11Crankshaft fluctuation sensor M side (CKFM)sensor - (ground for CKF sensor)WHT/RED
12Crankshaft position sensor M side (CKPM)sensor - (ground for CKP sensor)WHT
13Top dead centre sensor M side (TDCM)sensor - (ground for TDC sensor)RED
14Cylinder position sensor M side (CYPM)sensor - (ground for CYP sensor)BLKHonda's terminal-name column prints 'CKP SENSOR M SIDE' here; the description column says ground for the CYP sensor.
15VTEC pressure switch (VTM)0 V at low engine speed, battery voltage at high engine speedBLU/BLKD16Y5 and D16Y8 engines (footnote *12).
16Power steering oil pressure switch (PSPSW)0 V wheel straight at idle, battery voltage at full lockGRN
17Alternator FR signal (ALTF)0 V to battery voltage depending on electrical loadWHT/RED
18Vehicle speed sensor (VSS)cycles 0 V to 5 V with ignition ON and front wheels turningBLU/WHT
23Air/fuel ratio (HO2S) sensor pump cell + (IP+)about 0.5-5.3 V with ignition ONBLKM/T D16Y5 engine (footnote *10).
24Air/fuel ratio (HO2S) sensor common (IP-, VS-)reference, about 2.6-2.8 V warm idleREDM/T D16Y5 engine (footnote *10).
25Air/fuel ratio (HO2S) sensor VS cell voltage (VS+)about 7 V with ignition ONWHTM/T D16Y5 engine (footnote *10).
29A/T gear position switch N/P (ATPNP) or clutch switch (CLSW)ATPNP: 0 V in N or P; CLSW: about 5 V pedal released, 0 V pressedLT GRN / REDVariant: ATPNP, LT GRN wire, on CVT D16Y5 (footnote *3); CLSW, RED wire, on M/T D16Y5 (footnote *10).
30TCM to ECM data input (TMB)pulses with ignition ONPNKCVT D16Y5 engine (footnote *3).

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECM/PCM connector D (16P)16 cavities · 16 terminals listed · 16-cavity three-row plug as drawn by Honda: all 16 cavities numbered; terminals 5 and 12 are double-width cells.

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedHonda draws every ECM/PCM face as 'Wire side of female terminals': the harness plug seen from the wire-entry side, with a raised box drawn along the top edge. That has the same left-right orientation as looking straight into the ECU header, so the cells are stored exactly as drawn (ecu-side); the harness plug's mating face is the mirror image.
Honda Civic EK OBD2a ECM/PCM ('96-98): ECM/PCM connector D (16P)Raised box over cavities as drawn (latch side)1: Throttle position sensor (TPS)12: Engine coolant temperature sensor (ECT)23: Manifold absolute pressure sensor (MAP)34: Sensor voltage for MAP sensor (VCC1)45: Brake switch (BKSW)56: Knock sensor (KS)67: Primary heated oxygen sensor (PHO2S) or LABEL resistor78: Intake air temperature sensor (IAT)89: EGR valve lift sensor (EGRL)910: Sensor voltage (VCC2)1011: Sensor ground (SG2)1112: Sensor ground for MAP sensor (SG1)1213: Secondary heated oxygen sensor ground (SHO2SG)1314: Secondary heated oxygen sensor, sensor 2 (SHO2S)1415: Fuel tank pressure sensor (PTANK)1516: Electrical load detector (EL)16
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Throttle position sensor (TPS)0-5 V analog: about 0.5 V closed, 4.8 V wide openRED/BLK
2Engine coolant temperature sensor (ECT)0.1-4.8 V analogRED/WHT
3Manifold absolute pressure sensor (MAP)0-5 V analog: about 3 V ignition ON, 1.0 V idleRED/GRN
4Sensor voltage for MAP sensor (VCC1)5 V supply with ignition ONYEL/RED
5Brake switch (BKSW)0 V pedal released, battery voltage pressedGRN/WHT
6Knock sensor (KS)pulses with engine knockingRED/BLUCVT D16Y5 and D16Y8 engines (footnote *7).
7Primary heated oxygen sensor (PHO2S) or LABEL resistorPHO2S: above 0.6 V rich, below 0.4 V lean; LABEL: about 0.3-4.9 VWHTVariant: PHO2S except M/T D16Y5 (footnote *11); LABEL resistor input on M/T D16Y5 (footnote *10). Both WHT.
8Intake air temperature sensor (IAT)0.1-4.8 V analogRED/YEL
9EGR valve lift sensor (EGRL)about 1.2 V idle without vacuumWHT/BLKCVT D16Y5 engine (footnote *3).
10Sensor voltage (VCC2)5 V supply with ignition ONYEL/BLU
11Sensor ground (SG2)< 1.0 V at all timesGRN/BLK
12Sensor ground for MAP sensor (SG1)< 1.0 V at all timesGRN/WHT
13Secondary heated oxygen sensor ground (SHO2SG)sensor groundGRN/BLK / RED/YELWire colour: GRN/BLK on D16Y5 and D16Y8 (footnote *12), RED/YEL on D16Y7 (footnote *14).
14Secondary heated oxygen sensor, sensor 2 (SHO2S)above 0.6 V rich, below 0.4 V leanWHT/RED
15Fuel tank pressure sensor (PTANK)about 2.5 V with fuel cap openLT GRNFitted per Honda footnote *8: '96 D16Y8 (coupe), '97 D16Y8 (coupe all models, sedan KL model), '98 D16Y5, '98 D16Y8, '99-00 D16Y5 M/T and footnote *15: '97 D16Y7 (coupe KL model, sedan KL (LX) model), '98 D16Y7.
16Electrical load detector (EL)about 2.5-3.5 V parking lights at idle, 1.5-2.5 V low beamGRN/REDUSA model (footnote *1).

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

Year split: Honda's 1996-2000 Civic manual uses this table for all '96-98 models and for the '99-00 D16Y5 with M/T. Every other '99-00 Civic, including the EX (D16Y8) and Si (B16A2), uses a different pin assignment in the same four housings; see the OBD2b file. The catalog row for the EK EX / Si spans 1996-2000, so only its 1996-98 EX cars use this table.

Many terminals depend on engine and transmission. Honda footnotes them by engine (D16Y5, D16Y7, D16Y8), transmission (M/T, A/T, CVT), market (USA, Canadian KL) and year; each pin's notes repeat the footnote. Where one cavity has two uses (A7, C29, D7) the variants are listed on that pin. Connector B is wired only on A/T D16Y7 and D16Y8 cars.

Honda calls the unit ECM on manual cars and PCM when it also controls the automatic transmission. The footnotes on this table name only the D16Y5, D16Y7 and D16Y8 engines; the B16A2 (Civic Si) appears only in the '99-00 table.

Not covered here: the EK9 Civic Type R (B16B, Japan-market) and European or Australian EK Civics, which Honda's U.S. manual does not document, and the DC2 Integra. The 1998 Integra manual prints its own ECM table (connectors A 32P, C 31P and D 16P, no B) with different assignments, so Integra ECUs are not interchangeable with these tables.

Before working on the connectors, disconnect the battery negative terminal. The ECM/PCM sits behind the right kick panel under the carpet (Honda p. 11-83). Honda's own procedure back-probes from the wire side with its contoured back-probe set; never force sharp probes into the terminal side or past a seal, and never jump a connector while the ignition is ON.

Honda Civic EK OBD2b ECM/PCM ('99-00)

The 1999-2000 US-market Civic (EK) ECM/PCM, including the EX (D16Y8) and Si (B16A2), uses the same four Honda housings as 1996-98 but a different pin map: A (32P), B (25P), C (31P) and D (16P, A/T or CVT only). Honda's manual assigns 84 terminals across 104 cavities, footnoted by engine and transmission.

1999-2000 (except D16Y5 M/T) · USA and Canada (Honda U.S. service manual); Canadian KL models called out in footnotes · 4 connectors, 104 cavities · 84 terminals sourced

ECM/PCM connector A (32P)32 cavities · 24 terminals listed · 32-cavity three-row plug as drawn by Honda: 24 numbered terminals plus 8 crossed-out cavities; cells 10, 11, 23, 24 and 32 are double width. Same cavity layout as the '96-98 connector A, different pin assignment.

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedHonda draws every ECM/PCM face as 'Wire side of female terminals': the harness plug seen from the wire-entry side, with a raised box drawn along the top edge. That has the same left-right orientation as looking straight into the ECU header, so the cells are stored exactly as drawn (ecu-side); the harness plug's mating face is the mirror image.
Honda Civic EK OBD2b ECM/PCM ('99-00): ECM/PCM connector A (32P)Raised box over cavities as drawn (latch side)Cavity with no terminal numberCavity with no terminal number3: EVAP bypass solenoid valve (2WBS)34: EVAP control canister vent shut valve (VSV)45: Cruise control signal (CRS)56: EVAP purge control solenoid valve (PCS)67: A/T gear position switch D (ATPD)78: Secondary heated oxygen sensor heater control (SO2SHTC)89: A/T gear position switch P/N (ATPNP)910: Service check signal (SCS)10Cavity with no terminal numberCavity with no terminal numberCavity with no terminal number14: D4 indicator (D4IND)14Cavity with no terminal number16: Fuel pump relay (FLR)1617: A/C clutch relay (ACC)1718: Malfunction indicator lamp (MIL)1819: Engine speed pulse output (NEP)1920: Radiator fan control (FANC)2021: K-line to data link connector (K-LINE)2122: A/T gear position switch L (ATP L)2223: Secondary heated oxygen sensor, sensor 2 (SHO2S)2324: Starter switch signal (STS)24Cavity with no terminal number26: Power steering pressure switch signal (PSPSW)2627: A/C switch signal (ACS)2728: Interlock control unit (SLU)2829: Fuel tank pressure sensor (PTANK)2930: Electrical load detector (EL)30Cavity with no terminal number32: Brake switch (BKSW)32
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
3EVAP bypass solenoid valve (2WBS)battery voltage with ignition ONBLU
4EVAP control canister vent shut valve (VSV)battery voltage with ignition ONLT GRN/WHT
5Cruise control signal (CRS)downshift request pulses from the cruise control unitBLU/GRNA/T D16Y7, D16Y8 (footnote *1).
6EVAP purge control solenoid valve (PCS)battery voltage below 154 F (68 C) coolant, duty controlled aboveRED/YEL
7A/T gear position switch D (ATPD)0 V in D, about 5 V otherwiseYELCVT D16Y5 (footnote *3).
8Secondary heated oxygen sensor heater control (SO2SHTC)heater drive: battery voltage with ignition ON, duty controlled when warmBLK/WHT
9A/T gear position switch P/N (ATPNP)0 V in P or N, about 5 V otherwiseLT GRNCVT D16Y5 (footnote *3).
10Service check signal (SCS)0 V with service check connector jumped, about 5 V or battery voltage openBRN
14D4 indicator (D4IND)0 V with D4 indicator ON, battery voltage OFFGRN/BLKA/T D16Y7, D16Y8 (footnote *1).
16Fuel pump relay (FLR)0 V for 2 s after ignition ON, then battery voltageGRN/YEL
17A/C clutch relay (ACC)0 V with compressor ON, battery voltage OFFBLK/RED
18Malfunction indicator lamp (MIL)0 V with MIL ON, battery voltage OFFGRN/ORN
19Engine speed pulse output (NEP)engine speed pulses (tach signal) with engine runningBLU
20Radiator fan control (FANC)0 V with fan running, battery voltage stoppedGRN
21K-line to data link connector (K-LINE)OBD II scan tool serial line, pulses with ignition ONBLU/YEL
22A/T gear position switch L (ATP L)0 V in L, about 5 V otherwiseBLUCVT D16Y5 (footnote *3).
23Secondary heated oxygen sensor, sensor 2 (SHO2S)above 0.6 V rich, below 0.4 V leanWHT/RED
24Starter switch signal (STS)battery voltage while cranking (III)BLU/WHT
26Power steering pressure switch signal (PSPSW)0 V wheel straight at idle, battery voltage at full lockGRN
27A/C switch signal (ACS)0 V with A/C switch ON, about 5 V OFFBLU/RED
28Interlock control unit (SLU)battery voltage with ignition ON and brake pedal pressedWHT/REDA/T D16Y7, D16Y8 and CVT D16Y5 (footnotes *1, *3).
29Fuel tank pressure sensor (PTANK)about 2.5 V with fuel cap openLT GRNThe face view labels this cavity FTANK; the table says PTANK.
30Electrical load detector (EL)about 2.5-3.5 V parking lights at idle, 1.5-2.5 V low beamGRN/RED
32Brake switch (BKSW)0 V pedal released, battery voltage pressedGRN/WHT

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECM/PCM connector B (25P)25 cavities · 21 terminals listed · 25-cavity three-row plug as drawn by Honda: 21 numbered terminals plus 4 crossed-out cavities; the two left-hand columns are double-width cells. Same cavity layout as the '96-98 connector B.

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedHonda draws every ECM/PCM face as 'Wire side of female terminals': the harness plug seen from the wire-entry side, with a raised box drawn along the top edge. That has the same left-right orientation as looking straight into the ECU header, so the cells are stored exactly as drawn (ecu-side); the harness plug's mating face is the mirror image.
Honda Civic EK OBD2b ECM/PCM ('99-00): ECM/PCM connector B (25P)Raised box over cavities as drawn (latch side)1: Power source (IGP1)12: Power ground (PG1)23: No. 2 fuel injector (INJ2)34: No. 3 fuel injector (INJ3)45: No. 4 fuel injector (INJ4)56: Idle air control valve positive side (IACV P)67: EGR control solenoid valve (ESOL)78: CVT PH-PL control linear solenoid minus (HLC LSM) or A/T clutch pressure control solenoid minus (LS-)89: Power source (IGP2)910: Power ground (PG2)1011: No. 1 fuel injector (INJ1)1112: VTEC solenoid valve (VTS)1213: Ignition control module (ICM)13Cavity with no terminal number15: Idle air control valve negative side (IACV N)15Cavity with no terminal number17: A/T clutch pressure control solenoid plus (LS+) or CVT PH-PL control linear solenoid plus (HLC LSP)1718: CVT start clutch control linear solenoid minus (SC LSM)18Cavity with no terminal number20: Logic ground (LG1)2021: Voltage back up (VBU)2122: Logic ground (LG2)2223: Idle air control valve (IACV)23Cavity with no terminal number25: CVT start clutch control linear solenoid plus (SC LSP)25
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Power source (IGP1)battery voltage with ignition ON (II)YEL/BLK
2Power ground (PG1)< 1.0 V at all timesBLK
3No. 2 fuel injector (INJ2)injector drive, duty controlledRED
4No. 3 fuel injector (INJ3)injector drive, duty controlledBLU
5No. 4 fuel injector (INJ4)injector drive, duty controlledYEL
6Idle air control valve positive side (IACV P)duty controlled with engine runningBLK/BLUHonda lists B6/B15 (IACV P/N) and B23 (IACV) without a variant footnote on this page; check which idle valve the car has before wiring.
7EGR control solenoid valve (ESOL)duty controlled while EGR operates, 0 V otherwiseREDCVT D16Y5 (footnote *3). The face view labels this cavity ES.
8CVT PH-PL control linear solenoid minus (HLC LSM) or A/T clutch pressure control solenoid minus (LS-)solenoid return / duty controlledPNK/BLK / WHTVariant: HLC LSM, PNK/BLK wire, on CVT D16Y5 (footnote *3); LS-, WHT wire, on A/T D16Y7 and D16Y8 (footnote *1).
9Power source (IGP2)battery voltage with ignition ON (II)YEL/BLK
10Power ground (PG2)< 1.0 V at all timesBLK
11No. 1 fuel injector (INJ1)injector drive, duty controlledBRN
12VTEC solenoid valve (VTS)0 V at low rpm, battery voltage at high rpmGRN/YELD16Y5, D16Y8 and B16A2 engines (footnote *4).
13Ignition control module (ICM)ignition pulse to the ICM: battery voltage with ignition ON, pulses runningYEL/GRN
15Idle air control valve negative side (IACV N)duty controlled with engine runningORNSee the note on B6.
17A/T clutch pressure control solenoid plus (LS+) or CVT PH-PL control linear solenoid plus (HLC LSP)duty controlled / pulsing with ignition ONRED / GRN/WHTVariant: LS+, RED wire, on A/T D16Y7 and D16Y8 (footnote *1); HLC LSP, GRN/WHT wire, on CVT D16Y5 (footnote *3).
18CVT start clutch control linear solenoid minus (SC LSM)solenoid returnPNK/BLUCVT D16Y5 (footnote *3).
20Logic ground (LG1)< 1.0 V at all timesBRN/BLK
21Voltage back up (VBU)battery voltage at all times (DTC memory)WHT/BLU
22Logic ground (LG2)< 1.0 V at all timesBRN/BLK
23Idle air control valve (IACV)duty controlled with engine runningBLK/BLUSee the note on B6.
25CVT start clutch control linear solenoid plus (SC LSP)pulsing with ignition ONYELCVT D16Y5 (footnote *3).

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECM/PCM connector C (31P)31 cavities · 24 terminals listed · 31-cavity three-row plug as drawn by Honda: 24 numbered terminals plus 7 crossed-out cavities. Same cavity layout as the '96-98 connector C.

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedHonda draws every ECM/PCM face as 'Wire side of female terminals': the harness plug seen from the wire-entry side, with a raised box drawn along the top edge. That has the same left-right orientation as looking straight into the ECU header, so the cells are stored exactly as drawn (ecu-side); the harness plug's mating face is the mirror image.
Honda Civic EK OBD2b ECM/PCM ('99-00): ECM/PCM connector C (31P)Raised box over cavities as drawn (latch side)1: Primary heated oxygen sensor heater control (PO2SHTC)12: Alternator control (ALTC)23: Knock sensor (KS)3Cavity with no terminal number5: Alternator FR signal (ALTF)56: EGR valve lift sensor (EGRL)67: Sensor ground for MAP sensor (SG1)78: Crankshaft position sensor P side (CKPP)89: Crankshaft position sensor M side (CKPM)910: VTEC pressure switch signal (VTM)10Cavity with no terminal numberCavity with no terminal numberCavity with no terminal numberCavity with no terminal numberCavity with no terminal number16: Primary heated oxygen sensor, sensor 1 (PHO2S)1617: Manifold absolute pressure sensor (MAP)1718: Sensor ground (SG2)1819: Sensor voltage for MAP sensor (VCC1)1920: Top dead centre sensor P side (TDCP)2021: Top dead centre sensor M side (TDCM)2122: Crankshaft fluctuation sensor P side (CKFP)2223: Vehicle speed sensor (VSS)23Cavity with no terminal number25: Intake air temperature sensor (IAT)2526: Engine coolant temperature sensor (ECT)2627: Throttle position sensor (TPS)2728: Sensor voltage (VCC2)2829: Cylinder position sensor P side (CYPP)2930: Cylinder position sensor M side (CYPM)3031: Crankshaft fluctuation sensor M side (CKFM)31
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Primary heated oxygen sensor heater control (PO2SHTC)heater drive: battery voltage with ignition ON, duty controlled when warmBLK/WHT
2Alternator control (ALTC)battery voltage warm running, 0 V under small electrical loadWHT/GRN
3Knock sensor (KS)pulses with engine knockingRED/BLU
5Alternator FR signal (ALTF)0 V to battery voltage depending on electrical loadWHT/RED
6EGR valve lift sensor (EGRL)about 1.2 V idleWHT/BLKCVT D16Y5 (footnote *3).
7Sensor ground for MAP sensor (SG1)< 1.0 V at all timesGRN/WHT
8Crankshaft position sensor P side (CKPP)sensor + : pulses with engine runningBLU
9Crankshaft position sensor M side (CKPM)sensor - (ground for CKP sensor)WHT
10VTEC pressure switch signal (VTM)0 V at low engine speed, battery voltage at high engine speedBLU/BLKD16Y5, D16Y8 and B16A2 engines (footnote *4).
16Primary heated oxygen sensor, sensor 1 (PHO2S)above 0.6 V rich, below 0.4 V leanWHT
17Manifold absolute pressure sensor (MAP)0-5 V analog: about 3 V ignition ON, 1.0 V idleRED/GRN
18Sensor ground (SG2)< 1.0 V at all timesGRN/BLK
19Sensor voltage for MAP sensor (VCC1)5 V supply with ignition ONYEL/RED
20Top dead centre sensor P side (TDCP)sensor + : pulses with engine runningGRN
21Top dead centre sensor M side (TDCM)sensor - (ground for TDC sensor)RED
22Crankshaft fluctuation sensor P side (CKFP)sensor + : pulses with engine runningBLU/RED
23Vehicle speed sensor (VSS)cycles 0 V to about 5 V or battery voltage with front wheels turningBLU/WHT
25Intake air temperature sensor (IAT)0.1-4.8 V analogRED/YEL
26Engine coolant temperature sensor (ECT)0.1-4.8 V analogRED/WHT
27Throttle position sensor (TPS)0-5 V analog: about 0.5 V closed, 4.8 V wide openRED/BLK
28Sensor voltage (VCC2)5 V supply with ignition ONYEL/BLU
29Cylinder position sensor P side (CYPP)sensor + : pulses with engine runningYEL
30Cylinder position sensor M side (CYPM)sensor - (ground for CYP sensor)BLK
31Crankshaft fluctuation sensor M side (CKFM)sensor - (ground for CKF sensor)WHT/RED

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECM/PCM connector D (16P)16 cavities · 15 terminals listed · 16-cavity three-row plug as drawn by Honda; terminals 5 and 12 are double width. Same cavity layout as the '96-98 connector D. Transmission (A/T or CVT) connector.

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedHonda draws every ECM/PCM face as 'Wire side of female terminals': the harness plug seen from the wire-entry side, with a raised box drawn along the top edge. That has the same left-right orientation as looking straight into the ECU header, so the cells are stored exactly as drawn (ecu-side); the harness plug's mating face is the mirror image.
Honda Civic EK OBD2b ECM/PCM ('99-00): ECM/PCM connector D (16P)Raised box over cavities as drawn (latch side)1: Lock-up control solenoid valve A (LCA) on A/T; secondary gear shaft speed sensor (VEL) on CVT12: Shift control solenoid valve B (SHB) on A/T; inhibitor solenoid (INHSOL) on CVT23: Lock-up control solenoid valve B (LCB) on A/T; shift control linear solenoid minus (SHLSM) on CVT34: Shift control linear solenoid plus (SHLSP), CVT only45: Battery voltage for solenoid valves (VBSOL)56: Gear position switch R (ATPR)67: Shift control solenoid valve A (SHA) on A/T; secondary gear shaft speed sensor ground (VELSG) on CVT78: A/T gear position switch D3 (ATPD3), A/T only89: A/T gear position switch D4 (ATPD4), A/T only910: Countershaft speed sensor (NC) on A/T; driven pulley speed sensor (NDN) on CVT1011: Mainshaft speed sensor (NM) on A/T; drive pulley speed sensor (NDR) on CVT1112: Mainshaft speed sensor ground (NMSG) on A/T; drive pulley speed sensor ground (NDRSG) on CVT1213: A/T gear position switch P/N (ATPNP) on A/T; gear position switch S (ATPS) on CVT1314: A/T gear position switch 2 (ATP2) on A/T; D indicator (DIND) on CVT14Cavity with no terminal number16: Countershaft speed sensor ground (NCSG) on A/T; driven pulley speed sensor ground (NDNSG) on CVT16
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Lock-up control solenoid valve A (LCA) on A/T; secondary gear shaft speed sensor (VEL) on CVTA/T: battery voltage with lock-up ON; CVT: speed pulsesYEL / WHT/REDVariant: LCA, YEL wire, A/T D16Y7/D16Y8 (p. 11-95); VEL sensor input, WHT/RED wire, CVT D16Y5 (p. 11-96). Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
2Shift control solenoid valve B (SHB) on A/T; inhibitor solenoid (INHSOL) on CVTsolenoid driveGRN/WHT / GRN/BLKVariant: SHB, GRN/WHT, A/T; INHSOL, GRN/BLK, CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
3Lock-up control solenoid valve B (LCB) on A/T; shift control linear solenoid minus (SHLSM) on CVTsolenoid drive / returnGRN/BLK / GRN/YELVariant: LCB, GRN/BLK, A/T; SHLSM, GRN/YEL, CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
4Shift control linear solenoid plus (SHLSP), CVT onlypulses with ignition ONBLU/WHTCVT D16Y5 only; Honda draws this cavity crossed out (no terminal) on the A/T face. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
5Battery voltage for solenoid valves (VBSOL)battery voltage with ignition ONBLK/YELA/T and CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
6Gear position switch R (ATPR)0 V in R, about 10 V otherwiseWHTA/T and CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
7Shift control solenoid valve A (SHA) on A/T; secondary gear shaft speed sensor ground (VELSG) on CVTsolenoid drive / sensor groundBLU/YEL / BLK/WHTVariant: SHA, BLU/YEL, A/T; VELSG sensor ground, BLK/WHT, CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
8A/T gear position switch D3 (ATPD3), A/T only0 V in D3, about 10 V otherwisePNKA/T only; crossed out on the CVT face. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
9A/T gear position switch D4 (ATPD4), A/T only0 V in D4, about 5 V otherwiseYELA/T only; crossed out on the CVT face. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
10Countershaft speed sensor (NC) on A/T; driven pulley speed sensor (NDN) on CVTspeed pulsesBLU / WHTVariant: NC, BLU, A/T; NDN, WHT, CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
11Mainshaft speed sensor (NM) on A/T; drive pulley speed sensor (NDR) on CVTspeed pulsesRED / RED/BLUVariant: NM, RED, A/T; NDR, RED/BLU, CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
12Mainshaft speed sensor ground (NMSG) on A/T; drive pulley speed sensor ground (NDRSG) on CVTsensor groundWHT / GRNVariant: NMSG, WHT, A/T; NDRSG, GRN, CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
13A/T gear position switch P/N (ATPNP) on A/T; gear position switch S (ATPS) on CVT0 V in the named position, about 10 V otherwiseLT GRN / LT GRN/REDVariant: ATPNP, LT GRN, A/T; ATPS, LT GRN/RED, CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
14A/T gear position switch 2 (ATP2) on A/T; D indicator (DIND) on CVTA/T: 0 V in 2; CVT: 5 V drive to the D indicatorBLU / GRN/BLKVariant: ATP2 input, BLU, A/T; DIND output, GRN/BLK, CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.
16Countershaft speed sensor ground (NCSG) on A/T; driven pulley speed sensor ground (NDNSG) on CVTsensor groundGRN / RED/WHTVariant: NCSG, GRN, A/T; NDNSG, RED/WHT, CVT. Connector D is a transmission connector: Honda lists no M/T use for it in the '99-00 table.

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

Year split: Honda's 1996-2000 Civic manual prints this table for '99-00 models except the D16Y5 with M/T, which keeps the 1996-98 assignment (see the OBD2a file). The catalog row for the EK EX / Si spans 1996-2000; its 1999-2000 EX (D16Y8) and Si (B16A2) cars use this table. B16A2 is named in footnote *4 on VTS (B12) and VTM (C10).

The four housings and cavity layouts match the 1996-98 faces, but almost every signal moves: for example injectors move from A1-A4 to B3, B4, B5 and B11, and the K-line from C8 to A21. Do not mix an OBD2a harness and an OBD2b ECU without re-pinning.

Variant footnotes on these pages: *1 A/T (D16Y7, D16Y8), *2 M/T, *3 CVT (D16Y5), *4 D16Y5, D16Y8, B16A2. Connector D is printed twice, once for A/T and once for CVT; both are merged per cavity here with the variant in each pin's notes. Unmarked terminals apply to every '99-00 model this table covers.

Not covered here: the EK9 Civic Type R (B16B, Japan-market) and European or Australian EK Civics, which Honda's U.S. manual does not document, and the DC2 Integra. The 1998 Integra manual prints its own ECM table (connectors A 32P, C 31P and D 16P, no B) with different assignments, so Integra ECUs are not interchangeable with these tables.

Before working on the connectors, disconnect the battery negative terminal. The ECM/PCM sits behind the right kick panel under the carpet (Honda p. 11-83). Honda's own procedure back-probes from the wire side with its contoured back-probe set; never force sharp probes into the terminal side or past a seal, and never jump a connector while the ignition is ON.

All factory ECU pinouts →

Plug-and-play harness

Route for this carFactory-connector adapter
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

No Haltech S3 plug-in harness is listed for this vehicle, but a Boomslang adapter harness is: it plugs into the factory ECU connector on one side and the S3 pinout on the other, so the ECU2 replaces the factory ECU without cutting the loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.

MakerHarnessFitsLink
Manual 1996 - 1999 Acura IntegraBF29004-S3Label 1996-99, selector 1996-2001; manual$840LowestMaker ↗
Manual 2000 - 2001 Acura IntegraBF29005-S3Label 2000-01, selector 1998-2002; manual; 37820-P2P-A12 = 1999-2000 Civic 4-door non-VT…$840LowestMaker ↗
Wire-inUniversal flying lead or re-terminated factory harnessAny engine (terminate to ECU2's two Superseal 34 connectors)Universal harness from $405Maker ↗

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1996 - 1999 Acura Integra

$840USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Honda OBD2a ECU (1996-98 Civic/Integra/Accord/Prelude)
ECU
Honda OBD2
Confidence
low

Label (1996-99) and selector years (1996-2001) disagree; may straddle OBD2a/OBD2b. No numbers verified.

Fits
Label 1996-99, selector 1996-2001; manual
Exclusions
OBD2a vs OBD2b connector split around 1998-99 - confirm
SKU
BF29004-S3
Maker fitment
Acura Integra; Honda Accord; Honda Civic; Honda Prelude (Manual); selector years 1996-2001; SKU label: Manual 1996 - 1999 Acura Integra
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); USDM selector

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 2000 - 2001 Acura Integra

$840USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Honda OBD2b ECU (1999-2001 Civic/Integra/Accord) · 37820-P2P-A12, 37820-P2P-A11
OEM part numbers
37820-P2P-A12, 37820-P2P-A11
ECU
Honda OBD2
Confidence
low

Part numbers are examples for one Civic variant only (dealer catalogue snippet); Integra/Accord codes not verified.

Sources: E-1461

Fits
Label 2000-01, selector 1998-2002; manual; 37820-P2P-A12 = 1999-2000 Civic 4-door non-VTEC-E
SKU
BF29005-S3
Maker fitment
Acura Integra; Honda Accord; Honda Civic (Manual); selector years 1998-2002; SKU label: Manual 2000 - 2001 Acura Integra
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 2000-01

Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.

Your GAINS system for this car · pre-release

ECU2 for the Civic EK

Planned with the same rules as the configurator for this car's 4 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

Honda Civic EK EX / Si (D16Y8 / B16A2) studio render
Civic EK
  • ECU2Engine controller

    4 cyl · port injection · cable throttle

    Runs this 4-cylinder's injectors and its distributor on one ignition output, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harnessNone listed for this car
  2. Factory-connector → S3 adapter2 listed · from $840 USD listBF29004-S3
  3. Wire-inAlways possible

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Civic EK

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    VTEC crossoverplanned

    VTEC engagement is treated as a load and rpm surface where the two cam profiles cross on torque, learned from logs rather than a single fixed rpm.

  4. 4
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  5. 5
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAP speed-density (medium confidence)

  6. 6
    Wideband sensorhardware

    factory sensor type changes by year/market (narrowband on earlier cars); fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller either way

  7. 7
    Bottom end and head sealingfactory reference

    Reported: Ring lands of the stock pistons are commonly reported (forum) as the first failure under boost; an Edelbrock turbo-kit install sheet reportedly calls ~7-8 psi typical for a healthy stock D16Y8 and recommends aftermarket pistons, rods and valves above that (search excerpt; PDF returned 403 on fetch). (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Drivetrain

Si transmission5-speed manualSourced4

Chassis integration

Si chassis upgrades

Stiffer springs and stabilizer bars, larger exhaust and brakes, strut-tower brace, 15-inch tyres

Sourced4

Tuning notes

For B-series builds, decide early between keeping OBD2 (better for emissions inspection) or converting to OBD1 (broader tuning support), because it drives the harness, distributor and sometimes injector choices.

Popular swaps

K-series mounts

Hasport EKK kit, for EK chassis fitted with an EG/DC2-type subframe

Sourced · medium3
OBD-related hardwareInjectors and distributor differ by OBD versionLow confidence2

GAINS on the Civic EK

ECU2

ECU2Runs this 4-cylinder's injectors and its distributor on one ignition output, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

What engine is in the 1999-2000 Civic Si?

The B16A2 1.6-litre DOHC VTEC, rated at 160 hp and 111 lb-ft.4

Is the EK Civic OBD2a or OBD2b?

1996-98 cars are OBD2a and 1999-2000 cars are OBD2b.6

Can I run an OBD1 ECU in a 96-98 Civic?

Yes. OBD2A-to-OBD1 jumper harnesses let a 1992-95 manual-transmission ECU plug into a 1996-98 chassis.5

Which mounts do I need to K-swap an EK?

Hasport's EKK kit, which requires an EG/DC2-type subframe in the EK.3

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. California Air Resources Board OBD II staff report (1996 rulemaking) · California Air Resources Board · press · retrieved 2026-10-25
  2. Honda GSR OBD1 to OBD2 (forum thread) · Grassroots Motorsports forum · community · retrieved 2026-10-25
  3. EKK K-Series Mount Kit (96-00 Civic, EG/DC2 subframe) · Hasport Performance · vendor-doc · retrieved 2026-10-25
  4. Honda Civic Si Timeline and Milestones · American Honda Motor Co. (hondanews.com) · press · retrieved 2026-10-25
  5. SpeedFactory OBD2A to OBD1 ECU Jumper Harness for 96-98 Honda listing · Hybrid Racing · vendor-doc · retrieved 2026-10-25
  6. Honda B engine · Wikipedia · community · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  • Catalog note: B / K-swap chassis
  1. E-934 Boomslang identity (sourced, high confidence)
  2. E-935 Boomslang S3 catalog size (sourced, high confidence)
  3. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  4. E-941 S3 engine harness availability (inferred, medium confidence)
  5. E-1461 Honda OBD2 ECU (secondary-catalogue, medium confidence)