Engine: 6G72TT (3000GT VR-4)
Part of the Mitsubishi 6G72 family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (320 hp at 6000 rpm, 315 lb-ft at 2500 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.
6G72TT (3000GT VR-4) data
- Load sensing
- MAF (Karman vortex)
- O2 sensor
- Not yet sourced
- Closed loop
- Not yet sourced
- Block
- Not yet sourced
- Rods / pistons
- pressed-in wrist pins on stock pistons (3SX vendor)
- Reported limit
- Not yet sourced
- Factory
- Top-feed, low impedance
- Impedance
- low (peak and hold)
- Direct-fit upgrades
- 5 maker-listed
- Knock
- piezo knock sensor
- MAP / MAF
- MD170165 (turbo 91-93)|MD183618 (turbo 94-99)
- O2 (upstream)
- narrowband zirconia
Factory ECU
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Mitsubishi 3000GT/GTO Z16A 6G72TT ECU (early)
- Applies to
- 1991-1993 3000GT VR-4 (and Dodge Stealth R/T Turbo), manual; USDM
- Not for
- California-spec units differ from federal
Resale listings: MD159966 91-92 VR4/Stealth Turbo federal (also said to work on 93); MD192589 91-93 VR4/Stealth Turbo.
- ECU family
- Mitsubishi 3000GT Z16A 6G72TT ECU (1994-95)
- Applies to
- 1994-1995 3000GT VR-4, manual (6-speed); USDM
No OEM number found.
- ECU family
- Mitsubishi 3000GT Z16A 6G72TT ECU (OBD-II / Euro)
- Applies to
- 1996-1999 3000GT VR-4 (USDM and Euro), manual
No OEM number found. Overlaps BF29077-S3 (1998-99 VR4); difference between SKUs not stated by a source.
- ECU family
- Mitsubishi GTO Z16A 6G72TT ECU (JDM)
- Applies to
- 1990-2001 GTO twin-turbo, manual; JDM
No OEM number found; one SKU spans all GTO years.
- ECU family
- Mitsubishi 3000GT Z16A 6G72TT ECU (OBD-II)
- Applies to
- 1998-1999 3000GT VR-4, manual; USDM
- Not for
- 1996-97 / Euro cars see BF29135-S3
No OEM number found.
Factory ECU pinout: pending
No OEM pin table is in our library yet for the 6G72TT (3000GT VR-4) factory ECU. We only publish pinouts drawn from the OEM service manual or the maker's own documents, and none has been sourced yet. Until then, wire from the harness maker's instructions or the factory service manual.
Plug-and-play harness
No Haltech S3 plug-in harness is listed for this vehicle, but a Boomslang adapter harness is: it plugs into the factory ECU connector on one side and the S3 pinout on the other, so the ECU2 replaces the factory ECU without cutting the loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
![]() | Manual 1991 - 1993 Mitsubishi 3000GT VR4BF29075-S3 | 1991-1993 3000GT VR-4 (and Dodge Stealth R/T Turbo), manual; USDM | $840Lowest | Maker ↗ |
![]() | Manual 1994 - 1995 Mitsubishi 3000GT VR4BF29076-S3 | 1994-1995 3000GT VR-4, manual (6-speed); USDM | $840Lowest | Maker ↗ |
![]() | Manual 1996 - 1999 Mitsubishi 3000GT VR4 EUROBF29135-S3 | 1996-1999 3000GT VR-4 (USDM and Euro), manual | $840Lowest | Maker ↗ |
![]() | Manual 1990 - 2001 Mitsubishi GTOBF29190-S3 | 1990-2001 GTO twin-turbo, manual; JDM | $840Lowest | Maker ↗ |
![]() | Manual 1998 - 1999 Mitsubishi 3000GT VR4BF29077-S3 | 1998-1999 3000GT VR-4, manual; USDM | $960 | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1991 - 1993 Mitsubishi 3000GT VR4
- Plugs into
ECU (6G72 twin-turbo, 3000GT VR-4 / Stealth R/T Turbo 1991-93) · MD159966, MD192589
- OEM part numbers
- MD159966, MD192589
- ECU
- Mitsubishi 3000GT/GTO Z16A 6G72TT ECU (early)
- Confidence
- low
Resale listings: MD159966 91-92 VR4/Stealth Turbo federal (also said to work on 93); MD192589 91-93 VR4/Stealth Turbo.
Sources: E-1487
- Fits
- 1991-1993 3000GT VR-4 (and Dodge Stealth R/T Turbo), manual; USDM
- Exclusions
- California-spec units differ from federal
- SKU
- BF29075-S3
- Maker fitment
- Mitsubishi 3000GT VR4 (Manual); selector years 1991-1993; SKU label: Manual 1991 - 1993 Mitsubishi 3000GT VR4
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 1991-93

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1994 - 1995 Mitsubishi 3000GT VR4
- Plugs into
ECU (6G72 twin-turbo, 3000GT VR-4 1994-95, OBD-I)
- ECU
- Mitsubishi 3000GT Z16A 6G72TT ECU (1994-95)
- Confidence
- low
No OEM number found.
- Fits
- 1994-1995 3000GT VR-4, manual (6-speed); USDM
- SKU
- BF29076-S3
- Maker fitment
- Mitsubishi 3000GT VR4 (Manual); selector years 1994-1995; SKU label: Manual 1994 - 1995 Mitsubishi 3000GT VR4
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 1994-95

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1998 - 1999 Mitsubishi 3000GT VR4
- Plugs into
ECU (6G72 twin-turbo, 3000GT VR-4 1998-99, OBD-II)
- ECU
- Mitsubishi 3000GT Z16A 6G72TT ECU (OBD-II)
- Confidence
- low
No OEM number found.
- Fits
- 1998-1999 3000GT VR-4, manual; USDM
- Exclusions
- 1996-97 / Euro cars see BF29135-S3
- SKU
- BF29077-S3
- Maker fitment
- Mitsubishi 3000GT VR4 (Manual); selector years 1998-1999; SKU label: Manual 1998 - 1999 Mitsubishi 3000GT VR4
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 1998-99

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1996 - 1999 Mitsubishi 3000GT VR4 EURO
- Plugs into
ECU (6G72 twin-turbo, 3000GT VR-4 1996-99 incl. Euro)
- ECU
- Mitsubishi 3000GT Z16A 6G72TT ECU (OBD-II / Euro)
- Confidence
- low
No OEM number found. Overlaps BF29077-S3 (1998-99 VR4); difference between SKUs not stated by a source.
- Fits
- 1996-1999 3000GT VR-4 (USDM and Euro), manual
- SKU
- BF29135-S3
- Maker fitment
- Mitsubishi 3000GT VR4; Mitsubishi 3000GT VR4 EURO (Manual); selector years 1996-1999; SKU label: Manual 1996 - 1999 Mitsubishi 3000GT VR4 EURO
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 1996-99 incl EURO

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1990 - 2001 Mitsubishi GTO
- Plugs into
ECU (6G72 twin-turbo, GTO Z16A, JDM)
- ECU
- Mitsubishi GTO Z16A 6G72TT ECU (JDM)
- Confidence
- low
No OEM number found; one SKU spans all GTO years.
- Fits
- 1990-2001 GTO twin-turbo, manual; JDM
- SKU
- BF29190-S3
- Maker fitment
- Mitsubishi GTO (Manual); selector years 1990-2001; SKU label: Manual 1990 - 2001 Mitsubishi GTO
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); Mitsubishi GTO (JDM) 1990-2001; non-turbo/turbo not stated
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the 3000GT VR-4 / GTO Z16A
Planned with the same rules as the configurator for this car's 6 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.
- Price TBA
ECU2Engine controller
6 cyl · port injection · cable throttle
Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harnessNone listed for this car
- Factory-connector → S3 adapter5 listed · from $840 USD listBF29075-S3
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
How GAINS approaches the 3000GT VR-4 / GTO Z16A
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3Boost controlgated
A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.
- 4Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 5Factory load sensingfactory reference
What the factory ECU measures load with: MAF (Karman vortex) (low confidence)
- 6Wideband sensorhardware
factory O2 type not yet sourced; plan on a Bosch LSU 4.9 for the GAINS ECU's built-in controller
- 7Bottom end and head sealingfactory reference
Reported: Per Automotive Tech Info, piston speed ~3,000 fpm at 6,000 rpm is high for durability; forums commonly cite ~400 whp for stock rods/pistons (not 6G72-specific). (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
GAINS on the 3000GT VR-4 / GTO Z16A
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)
- E-1487 harness ECU xref: Mitsubishi 3000GT VR-4 1991-93 (unverified, low confidence)


