Mitsubishi · 1990-94

Mitsubishi Eclipse / Talon (DSM) 1G 4G63T ECU and tuning guide

The Mitsubishi Eclipse / Talon (DSM) 1G 4G63T (1990-94) runs the 4G63T (DSM 1G / 2G): 2 L I4, turbocharged, port injection, cable throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Years1990-99
Displacement2L
LayoutI4
InductionTurbocharged
InjectionPort injection
Cam controlnone
IgnitionWasted spark
Swap demandHigh

Part of the Mitsubishi 4G63 family.

Modeled power and torque

Modelled estimate, not a dyno result.

4G63T (DSM 1G / 2G): stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
010020030040001002003004001k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (195 hp at 6000 rpm, 203 lb-ft at 3000 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.

4G63T (DSM 1G / 2G) data

Platform background

First-generation Diamond Star Motors turbo cars (Eclipse GS Turbo/GSX, Talon TSi/TSi AWD, Laser RS Turbo) use the 7.8:1-compression 4G63T with a Karman vortex airflow sensor, low-impedance injectors with a resistor pack, and a cam-driven CAS that carries both crank and cam signals. Early cars have the 6-bolt crank. OEM documentation for this platform was not available online in an acceptable form, so most rows here are low confidence and need checking against the factory service manual.

Factory ECU

Load sensing

Mitsubishi Karman vortex volume airflow sensor (frequency output)

Low confidence14
Injectors

450 cc (manual) / 390 cc (automatic), low impedance with a resistor pack

Low confidence24
Trigger
  • Cam angle sensor on the cam end providing both crank angle and cylinder ID
  • Adjustable for base timing
Low confidence3
TurboTD05-14B (manual) / TD04-13GautomaticLow confidence4

The 1G ECU is a Mitsubishi MPI unit of the same family as the Evo I-III. Automatic-transmission turbo cars had smaller injectors and turbo and a lower rating (180 hp), so the ECU calibration differs from manual cars. Swapping injectors without matching the ECU is a common source of fuelling errors.

Factory ECU: harness cross-reference

From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.

1G DSM turbo ECU (4G63T, Eclipse/Talon/Laser 1990-94)
MD166262MD166260MD145903
ECU family
Mitsubishi 1G DSM 4G63T ECU
Applies to
1990-1994 Eclipse GS-T/GSX (and Eagle Talon TSi / Plymouth Laser RS Turbo), manual
Not for
automatic (A/T ECU differs per forum); non-turbo
Supplier
Mitsubishi Electric

Numbers from resale listings only (MD166262 1990-93 M/T AWD; MD166260 1994 FWD M/T turbo; MD145903 1990 Talon TSi, label E2T34478). E2T prefix on label is a Mitsubishi Electric item code (supplier inferred from label prefix, low).

Low confidenceUnverifiedE-1483

Factory ECU pinout

Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.

Mitsubishi Eclipse / Eagle Talon / Plymouth Laser 1G 4G63T engine control unit (ECU)

The 1G DSM turbo ECU is the engine computer of the 1990-94 Eclipse GS Turbo/GSX, Talon TSi and Laser RS Turbo with the 4G63T. It has three connectors on the ECU, C-64, C-65 and C-66, with 52 cavities numbered 1-24, 51-68 and 101-110. Pins here come from the 1990 terminal table and the 1991 turbo wiring diagrams.

1990-1994 (transcribed from 1990 and 1991 manuals) · US / Canada · 3 connectors, 52 cavities · 52 terminals sourced

ECU connector C-66 (terminals 1-24)24 cavities · 24 terminals listed · 24-cavity, 2 rows of 12, lock ramp on top

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedECU (equipment) side, looking into the ECU header face, lock ramp at the top. The 1991 EWD 'How to Read Circuit Diagrams' (8-47) says symbols are shown facing in the direction indicated and that, for connections to equipment, the equipment's connector is shown; C-64 to C-66 are drawn with double outlines (male terminals), i.e. the ECU header.
Mitsubishi Eclipse / Eagle Talon / Plymouth Laser 1G 4G63T engine control unit (ECU): ECU connector C-66 (terminals 1-24)Lock rampKey / latchKey / latch1: Self-diagnosis output12: Diagnosis / data transfer select terminal23: Turbo meter (boost gauge)34: Oxygen sensor45: Power steering oil pressure switch56: Air flow sensor active filter reset (1991 EWD); idle position switch (1990)67: Air conditioner switch78: Intake air temperature sensor89: Detonation (knock) sensor910: Air flow sensor1011: Line to ABS control unit (AWD)1112: Ignition timing adjustment connector1213: Control relay (fuel pump drive signal)1314: Idle position switch (1991 EWD); air flow sensor active filter reset (1990)1415: EGR temperature sensor (California only)1516: Barometric pressure sensor1617: Sensor ground1718: Vehicle speed sensor1819: Throttle position sensor1920: Engine coolant temperature sensor2021: Crank angle sensor2122: Top dead center sensor2223: Power supply for sensors (5 V)2324: Sensor ground24
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Self-diagnosis outputdiagnostic output to self-diagnosis connector—Function from the 1990 terminal table; the wire is not labelled on the 1991 MPI pages used. (medium confidence)
2Diagnosis / data transfer select terminaldiagnostic select inputWRuns to self-diagnosis check connector terminal 10.
3Turbo meter (boost gauge)gauge driverBRTurbo models only.
4Oxygen sensor0-1 V narrowbandW
5Power steering oil pressure switchswitch input(YB)Colour in parentheses = 0.3 mm2 wire. (medium confidence)
6Air flow sensor active filter reset (1991 EWD); idle position switch (1990)reset output to AFSGWYear split: the 1991 circuit diagram wires AFS terminal 1 to ECU 6 and the idle switch to 14; the 1990 terminal table lists 6 = idle position switch and 14 = AFS filter reset (turbo). (medium confidence)
7Air conditioner switchswitch inputBG (medium confidence)
8Intake air temperature sensor0-5 V analog (thermistor)GOSensor is inside the air flow sensor.
9Detonation (knock) sensorpiezo knock signalWTurbo models only; shielded lead.
10Air flow sensorfrequency (Karman vortex)GL
11Line to ABS control unit (AWD)Comms / diagRL1991 EWD: AWD runs to the ABS control unit, FWD is not connected. The 1990 table lists 11 as unused. (medium confidence)
12Ignition timing adjustment connectorground-to-set input(B)
13Control relay (fuel pump drive signal)Outputs—From the 1990 terminal table; not located on the 1991 MPI turbo pages used. (medium confidence)
14Idle position switch (1991 EWD); air flow sensor active filter reset (1990)switch inputGSee terminal 6 for the 1990 / 1991 swap. (medium confidence)
15EGR temperature sensor (California only)0-5 V analog (thermistor)LY
16Barometric pressure sensor0-5 V analogGYSensor is inside the air flow sensor.
17Sensor groundsensor returnGB
18Vehicle speed sensorreed switch pulseYW
19Throttle position sensor0-5 V analogGW
20Engine coolant temperature sensor0-5 V analog (thermistor)YG
21Crank angle sensoroptical sensor pulse (5 V pull-up)B
22Top dead center sensoroptical sensor pulse (5 V pull-up)W
23Power supply for sensors (5 V)5 V reference outGRFeeds the air flow sensor block and TPS.
24Sensor groundsensor returnGB

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECU connector C-65 (terminals 51-68)18 cavities · 18 terminals listed · 18-cavity, 2 rows of 9, lock ramp on top

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedECU (equipment) side, looking into the ECU header face, lock ramp at the top. The 1991 EWD 'How to Read Circuit Diagrams' (8-47) says symbols are shown facing in the direction indicated and that, for connections to equipment, the equipment's connector is shown; C-64 to C-66 are drawn with double outlines (male terminals), i.e. the ECU header.
Mitsubishi Eclipse / Eagle Talon / Plymouth Laser 1G 4G63T engine control unit (ECU): ECU connector C-65 (terminals 51-68)Lock rampKey / latchKey / latch51: No. 1 injector5152: No. 2 injector5253: EGR control solenoid valve (California only)5354: Power transistor for No. 1 and No. 4 cylinders5455: Power transistor for No. 2 and No. 3 cylinders5556: Control relay (fuel pump control)5657: Fuel pressure control valve5758: Idle speed control servo coil A15859: Idle speed control servo coil A25960: No. 3 injector6061: No. 4 injector6162: Purge control solenoid valve6263: Control relay6364: Engine warning light (malfunction indicator light)6465: Air conditioner relay6566: Control relay6667: Idle speed control servo coil B16768: Idle speed control servo coil B268
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
51No. 1 injectorlow-side injector driverYLInjector feed via resistor A-58 from the MPI control relay.
52No. 2 injectorlow-side injector driverYB
53EGR control solenoid valve (California only)low-side solenoid driverBY
54Power transistor for No. 1 and No. 4 cylindersigniter trigger outputYRotated single-letter label; read as Y on both the M/T and A/T pages. (medium confidence)
55Power transistor for No. 2 and No. 3 cylindersigniter trigger outputYR
56Control relay (fuel pump control)low-side relay driverWR
57Fuel pressure control valvelow-side solenoid driverWTurbo models only.
58Idle speed control servo coil A1stepper coil driverL
59Idle speed control servo coil A2stepper coil driverY
60No. 3 injectorlow-side injector driverLg
61No. 4 injectorlow-side injector driverLgW
62Purge control solenoid valvelow-side solenoid driverBW
63Control relaylow-side relay driverBL
64Engine warning light (malfunction indicator light)low-side lamp driverRG
65Air conditioner relaylow-side relay driver(RB)
66Control relaylow-side relay driverBL
67Idle speed control servo coil B1stepper coil driverW
68Idle speed control servo coil B2stepper coil driverB

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECU connector C-64 (terminals 101-110)10 cavities · 10 terminals listed · 10-cavity, 2 rows of 5, lock ramp on top

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedECU (equipment) side, looking into the ECU header face, lock ramp at the top. The 1991 EWD 'How to Read Circuit Diagrams' (8-47) says symbols are shown facing in the direction indicated and that, for connections to equipment, the equipment's connector is shown; C-64 to C-66 are drawn with double outlines (male terminals), i.e. the ECU header.
Mitsubishi Eclipse / Eagle Talon / Plymouth Laser 1G 4G63T engine control unit (ECU): ECU connector C-64 (terminals 101-110)Lock rampKey / latchKey / latch101: Ground101102: Power supply (from control relay)102103: Power supply for backup103104: Inhibitor switch (A/T)104105: Waste gate solenoid valve105106: Ground106107: Power supply (from control relay)107108: Ignition switch ST terminal108109: Ignition pulse detect109110: Ignition switch IG terminal110
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
101Groundground1.25-B
102Power supply (from control relay)12 V switched input1.25-R
103Power supply for backup12 V permanentRB
104Inhibitor switch (A/T)switch input2-BYA/T wire colour. On M/T the 1991 diagram shows 104 on a B wire to ground. (medium confidence)
105Waste gate solenoid valvelow-side solenoid driverOTurbo models only.
106Groundground1.25-B
107Power supply (from control relay)12 V switched input1.25-R
108Ignition switch ST terminal12 V input while cranking1.25-RY
109Ignition pulse detectignition pulse input (shared with tachometer)W
110Ignition switch IG terminal12 V ignition input1.25-BW

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

1990 vs 1991+: the 1990 terminal table lists 6 = idle position switch and 14 = air flow sensor active filter reset, while the 1991 turbo circuit diagram wires the AFS reset (GW) to 6 and the idle switch (G) to 14. Check the year of both the ECU and the harness before swapping a 1990 ECU into a later car or the reverse.

Coverage: functions come from the 1990 Technical Information Manual table (turbo-only terminals 3, 9, 14, 57 and 105 marked there) and wire colours from the 1991 Laser/Talon turbo M/T and A/T circuit diagrams. 1992-94 manuals were not available for checking, so confirm those years before wiring. Terminal 104 is the A/T inhibitor switch; M/T ties it to ground.

Wire colours are as printed (Mitsubishi code without hyphens on single-size runs, e.g. YL = yellow with blue tracer, Lg = light green; leading number = mm2; colours in parentheses = 0.3 mm2). Not covered: 1.8L SOHC and 2.0L non-turbo ECUs, which have different terminal use.

Safety: disconnect the battery before unplugging the ECU, and probe from the wire side with a fine probe; never force sharp probes into the terminals.

All factory ECU pinouts →

Plug-and-play harness

Route for this carFactory-connector adapter
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

No Haltech S3 plug-in harness is listed for this vehicle, but a Boomslang adapter harness is: it plugs into the factory ECU connector on one side and the S3 pinout on the other, so the ECU2 replaces the factory ECU without cutting the loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.

MakerHarnessFitsLink
Manual 1990 - 1994 Mitsubishi Eclipse TurboBF29050-S31990-1994 Eclipse GS-T/GSX (and Eagle Talon TSi / Plymouth Laser RS Turbo), manual$840Maker ↗
Wire-inUniversal flying lead or re-terminated factory harnessAny engine (terminate to ECU2's two Superseal 34 connectors)Universal harness from $405Maker ↗

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1990 - 1994 Mitsubishi Eclipse Turbo

$840USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
1G DSM turbo ECU (4G63T, Eclipse/Talon/Laser 1990-94) · MD166262, MD166260…
OEM part numbers
MD166262, MD166260, MD145903
ECU
Mitsubishi Electric · Mitsubishi 1G DSM 4G63T ECU
Confidence
low

Numbers from resale listings only (MD166262 1990-93 M/T AWD; MD166260 1994 FWD M/T turbo; MD145903 1990 Talon TSi, label E2T34478). E2T prefix on label is a Mitsubishi Electric item code (supplier inferred from label prefix, low).

Sources: E-1483

Fits
1990-1994 Eclipse GS-T/GSX (and Eagle Talon TSi / Plymouth Laser RS Turbo), manual
Exclusions
automatic (A/T ECU differs per forum); non-turbo
SKU
BF29050-S3
Maker fitment
Mitsubishi Eclipse Turbo (Manual); selector years 1990-1994; SKU label: Manual 1990 - 1994 Mitsubishi Eclipse Turbo
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); Eclipse Turbo; Talon not listed separately

Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.

Your GAINS system for this car · pre-release

ECU2 for the Eclipse / Talon (DSM) 1G

Planned with the same rules as the configurator for this car's 4 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

  • ECU2Engine controller

    4 cyl · port injection · cable throttle

    Full sequential fuel and spark for this 4-cylinder on a cable throttle, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harnessNone listed for this car
  2. Factory-connector → S3 adapter1 listed · from $840 USD listBF29050-S3
  3. Wire-inAlways possible

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Eclipse / Talon (DSM) 1G

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Boost controlgated

    A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.

  4. 4
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  5. 5
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAF (Karman vortex) (medium confidence)

  6. 6
    Wideband sensorhardware

    Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller

  7. 7
    Bottom end and head sealingfactory reference

    Reported: 7-bolt engines commonly reported prone to crankwalk (thrust bearing), improved with 1997.5+ revised thrust (forum); rods/pistons cited before crank (forum). (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Drivetrain

Transmissions

F5M33 5MT (FWD turbo), W5M33 5MT (AWD), F4A33 4AT (FWD turbo), 4-speed AT (AWD)

Low confidence4
AWD (GSX / TSi AWD)

Center differential feeding a transfer case and rear differential (rear LSD fitted on some)

Low confidence4
Recall98V069001: 1990-98 GSX transfer case lubricationLow confidence4

Chassis integration

Facelift

1992 update with exposed headlights (pre-facelift cars have pop-ups)

Low confidence4

Tuning notes

Ratings
  • 1990 GS Turbo manual 190 hp
  • GSX manual 195 hp
  • All manual turbos 195 hp from 1991
  • Automatics 180 hp
Low confidence4
Compression7.8:1 with piston oil squirtersLow confidence4
Crank6-bolt until about April 1992, 7-bolt afterSourced · medium54
Throttle body60mmLow confidence4

Verify base timing at the CAS with a timing light before any calibration work, because the CAS is adjustable. Low static compression makes the 1G tolerant of boost, but the stock 450/390 cc low-impedance injectors and the airflow sensor are the first limits.

Popular swaps

Engine swaps
  • 2G and Evo 4G63T engines are common replacements
  • Evo IV+ engines are rotated and need orientation-matched parts
Low confidence63

GAINS on the Eclipse / Talon (DSM) 1G

ECU2

ECU2Full sequential fuel and spark for this 4-cylinder on a cable throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

What size injectors does a 1G DSM have?

Community references list 450 cc for manual turbo cars and 390 cc for automatics, both low impedance with a resistor pack.2

Is my 1G a 6-bolt or 7-bolt?

Engines built through about April 1992 are 6-bolt; from May 1992 they are 7-bolt. Check the flywheel flange to be sure.5

Can you adjust timing on a 1G DSM?

Yes. The 1G cam angle sensor is adjustable, unlike the 2G's fixed sensors.3

What compression ratio is the 1G 4G63T?

7.8:1.4

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. A Karman Vortex Airflow Sensor (SAE 820322) · SAE International · sae-paper · retrieved 2026-10-25
  2. Injector sizes (forum thread) · DSMTuners · community · retrieved 2026-10-25
  3. CAS and CKP sensors (forum thread) · DSMTuners · community · retrieved 2026-10-25
  4. Mitsubishi Eclipse · Wikipedia · community · retrieved 2026-10-25
  5. Mitsubishi Sirius engine (4G63 section) · Wikipedia · community · retrieved 2026-10-25
  6. Top Ten Engines - #3 Mitsubishi 4G63T · DSPORT Magazine · press · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  1. E-934 Boomslang identity (sourced, high confidence)
  2. E-935 Boomslang S3 catalog size (sourced, high confidence)
  3. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  4. E-941 S3 engine harness availability (inferred, medium confidence)
  5. E-1483 harness ECU xref: Mitsubishi DSM 4G63T ECUs (unverified, low confidence)