Bosch · Thermocouple with amplifier (0-5 V)

Bosch TCP-N amplified EGT thermocouple probe

Bosch Motorsport B 261 209 387Bosch Motorsport B 261 209 821 01

The Bosch TCP-N is a flexible type N (NiCrSi-NiSi) thermocouple probe for exhaust gas temperature with the amplifier built in: it runs on 12 V and outputs 0.5-4.5 V for -40 to 1,100 °C, so it wires straight to an analog input. Response time is 20 s for the TCP-N and 33 s for the TCP-NF.1

Key specifications

Measures: Exhaust gas temperature (-40 to 1,100 °C). Output: Thermocouple with amplifier (0-5 V).

ElementType N, NiCrSi-NiSiSourced1
Range-40 to 1,100°CSourced1
Output0.5-4.5VSourced1
Supply12VSourced1
Response
  • 20 sTCP-N
  • 33 sTCP-NF
Sourced1
Thread / torque
  • M12x1, 17 mm, 15 N·m
  • Length 630 mm
Sourced1
Part numberMakerNote
B 261 209 387Bosch MotorsportTCP-N1
B 261 209 821 01Bosch MotorsportTCP-NF (flexible)1

Pinout and connector

No pinout is shown: the maker or OEM does not publish one in a document we could cite. Identify pins with a meter before wiring.

Connector: 1-J0973-70 (TCP-N); D 261 205 276 (TCP-NF)1 Connector library

Terminals and seals: Not listed: the Bosch data sheet gives the mating housing only, not contact or seal part numbers.

Transfer function and calibration data

Output vs temperature1
3721,4902,6093,7274,845-402455308151,100Temperature (°C)Output (mV)
Show the 13 data points
Temperature (°C)Output (mV)
-40372
0485
100790
2001,135
3001,513
4001,912
5002,327
6002,752
7003,183
8003,615
9004,046
1,0004,473
1,1004,845

How it's calibrated

ECU-neutral: enter these values in whichever ECU you use. Nominal values without the maker's tolerance band.

Transfer function

  • 0.37–4.84 V → -40–1,100 °C1

Worked conversion

  • At 2.61 V the output corresponds to 567 °C.1Calculated from the maker's data
Output vs temperature: output voltage to temperature (9 rows)Calculated from the maker's data
Output (V)Temperature (°C)
0.54.9
1160.9
1.5296.6
2421.2
2.5540.7
3657.5
3.5773.4
4889.3
4.51007.3

Interpolated between the maker's published points; nominal values with no tolerance band.

Native support across ECUs

ECU platformStatusHow to set it upSource
GAINS ECU2ConceptConfigurable (generic input)Any AVI (AVI1-6; pins 17-20, 14 and 26 on the ECU2): 0-5 V input with the pull-up off. Concept hardware.Medium2
Haltech (Elite / Nexus)Configurable (generic input)Analog voltage input (AVI). Haltech's wiring diagram says inputs are user definable in software; enter the maker's transfer function.45
Link (G4X)Configurable (generic input)Analogue voltage input (9 on the G4X FuryX). Link's public page does not describe how a custom calibration is entered.Medium6
MoTeC (M1)Configurable (generic input)Analogue voltage input (17 on the M150). MoTeC's sensor pages show a manual-calibration option in M1 Tune.Medium78
ECUMaster (EMU Black)Configurable (generic input)One of 9 analog 0-5 V inputs. ECUMaster lists user-defined sensor characteristics for some functions.Medium9
AEM (Infinity)Configurable (generic input)Analog 0-5 V input (12-bit). AEM's spec sheet does not say how a custom calibration is entered.Medium10
MaxxECUConfigurable (generic input)Extra 0-5 V input (6 on the RACE). The public page does not describe calibration entry.Medium11
Holley (Terminator X / EFI)Configurable (generic input)'5' analog input, set up as a custom sensor in Holley's software (per the wiring manual).12

Third-party rows come only from each vendor's public product pages, sensor lists and spec sheets, retrieved on the dates listed in Sources; we do not use ECU software, help files, base maps or calibration files, and reproduce no vendor calibration values. "Preset listed" means the vendor publicly names this sensor; "Configurable" means a matching generic input is listed. Check the vendor's current documentation before buying.

Trademarks belong to their owners. Names are used only to identify compatible products; no endorsement is implied.

CAD and drawings

We link to the maker's own downloads and do not rehost their CAD or data sheets: the maker's terms do not grant redistribution. Registration may be needed on the maker's site.

Wiring and installation

Signal to an analog input with no pull-up; 12 V supply from a fused switched feed. The table is not quite linear, so enter it as a table rather than a straight line.Medium1

Failure modes and checks

Reads about -40 °C hot

Likely cause Open signal or no 12 V supply

Check Check supply and that the output sits above 0.37 V at ambient.Medium1

Lags behind events

Likely cause Probe response time

Check Expect 20-33 s response; EGT shows trends, not single events.Medium1

Frequently asked

What is the output of the Bosch TCP-N?

0.5-4.5 V over -40 to 1,100 °C from a 12 V supply; for example 2,327 mV at 500 °C and 4,473 mV at 1,000 °C.1

Does the TCP-N need a separate EGT amplifier?

No. The amplifier is built into the probe, which outputs 0.5-4.5 V.1

Related

Use it with GAINS

Bosch TCP-N amplified EGT thermocouple probe on GAINS hardware

ECU2AVI (0-5 V, pull-up off)

Pins
On the ECU2 pin map
Pull-up
Off
Shielding
Not needed

Any free analog input with its pull-up off; 5 V from pin 28, ground to pin 29.Medium2

GAINS hardware is pre-release concept design; pin numbers can change before release and none of it has been tested on a vehicle yet.23

Concept Pre-release hardware. Pin assignments come from the current design documents and may change.

Sources

12 sources
  1. Thermocouple Probe TCP-N / TCP-NF data sheet · Bosch Motorsport (Bosch Engineering GmbH) · vendor-doc · retrieved 2026-10-27
  2. internal GAINS internal: ECU2 concept and pin map v0.3 (hardware/mini-ecu/CONCEPT.md §3)
  3. internal GAINS internal: PDM2 input and output specification (hardware/mini-pdm/SPEC.md)
  4. Nexus R3 wiring diagram (HT-193000_WD) · Haltech · vendor-doc · retrieved 2026-10-27
  5. Nexus R3 VCU (HT-193000) product page · Haltech · vendor-doc · retrieved 2026-10-27
  6. M150 product page (M1 series) · MoTeC · vendor-doc · retrieved 2026-10-27
  7. TMAP Sensor product page · MoTeC · vendor-doc · retrieved 2026-10-27
  8. EMU Black product page · ECUMaster · vendor-doc · retrieved 2026-10-27
  9. Infinity Series 5 hardware specification · AEM Electronics · vendor-doc · retrieved 2026-10-27
  10. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-10-27
  11. HP / Dominator EFI wiring manual 199R10555 · Holley · vendor-doc · retrieved 2026-10-27

Not yet indexed: fewer than 3 FAQs.