Engine: LT4 (supercharged)
Part of the GM LT (Gen V) family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (650 hp at 6400 rpm, 650 lb-ft at 3600 rpm); the curve shape between peaks is modeled. Pulley + bolt-ons + tune (pump fuel): Stock turbo/supercharger; gains limited by compressor and fuel system.
LT4 (supercharged) data
- Load sensing
- MAF+MAP (blended / torque model)
- O2 sensor
- Not yet sourced
- Closed loop
- Not yet sourced
- Block
- aluminium (Gen V foundation shared with LT1)
- Rods / pistons
- forged powder-metal steel, machined lighter than LT1 rods · forged aluminium with stronger structure for boost
- Reported limit
- Not yet sourced
- Factory
- GDI (direct injection, solenoid)
- Impedance
- Not yet sourced
- Direct-fit upgrades
- 5 maker-listed
- Knock
- GM 12623095
- MAP / MAF
- GM 12711681 (repl 12694725, 12644228, 12594942, 12701247)
- O2 (upstream)
- GM 12655677
Platform background
The C7 Corvette (2014-19) introduced the Gen V LT1 with direct injection, cam phasing and AFM, and the 2015 Z06 added the supercharged LT4. The sixth-generation Camaro SS uses the LT1 and the ZL1 (2017-24) the LT4. All use the E92 ECM with a 58x/4x trigger and a cam-driven high-pressure DI pump.
Factory ECU
Factory-ECM recalibration is the standard route. The E92 manages DI, the phaser, AFM and the torque model that the transmission and stability systems use, so standalone conversions are rare on these cars.
Factory ECU pinout: pending
No OEM pin table is in our library yet for the LT4 (supercharged) factory ECU. No OEM-grade public pinout was found. Needed: the GM service manual Engine Controls / Wiring Systems section for this vehicle and year, giving the PCM/ECM connector end views and terminal tables. Specifically the 2014-2019 Corvette and 2016-2024 Camaro service manuals, E92 ECM connector terminal tables. Until then, wire from the harness maker's instructions or the factory service manual.
Factory ECU pinout
No OEM-grade public pinout was found. Needed: the GM service manual Engine Controls / Wiring Systems section for this vehicle and year, giving the PCM/ECM connector end views and terminal tables. Specifically the 2014-2019 Corvette and 2016-2024 Camaro service manuals, E92 ECM connector terminal tables.
Harness: wire-in
No plug-and-play harness for the S3 pinout is listed for this vehicle yet. The route is a universal wire-in harness: the factory ECU is removed and each circuit is wired to the new ECU from a pinout. Nothing is written to the factory ECU.
Being researched
We're mapping S3 plug-in and factory-connector adapter harnesses to this application.
Universal flying lead or re-terminated factory harness
Always available: terminate the engine side to ECU2's two Superseal 34 connectors. Universal harness from $405 USD list.
Your GAINS system for this car · pre-release
ECU2 + DI for the Corvette C7
Planned with the same rules as the configurator for this car's 8 cyl · direct injection · drive-by-wire. The factory ECU is unplugged and replaced; nothing is written to it.

- Price TBA
ECU2Engine controller
8 cyl · direct injection · drive-by-wire
Full sequential fuel and spark for this 8-cylinder, and its electronic throttle, with the wideband built in.
in designEst. availability: April 2027
- Price TBA
DIDirect injection
Drives the direct injectors and high-pressure fuel pump; ECU2 keeps the timing.
conceptEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- Drive-by-wire built inFour half-bridges run up to two electronic throttles, with pedal and throttle sensors on the ECU's own inputs and a windowed watchdog that cuts the motors in hardware on a fault.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
- Host keeps controlThe ECU decides when and how long each injector and pump valve fires.
- Independent safe stateDrivers stay inhibited unless both the supervisor and the hardware enable agree.
How it wires in
- Haltech S3 plug-in harnessNone listed for this car
- Factory-connector → S3 adapterNone listed for this car
- Wire-inYour route: universal wire-in harness
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
Swap guides
The LT4 (supercharged) family in other cars
How GAINS approaches the Corvette C7
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3Cam phasing (VVT)gated
Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.
- 4Boost controlgated
A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.
- 5Direct injectionplanned
Rail-pressure targets and injection phasing run on the DI driver. Dual-injection engines add a port / DI split, which starts from the factory's general strategy and is refined from logs.
- 6Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 7Factory load sensingfactory reference
What the factory ECU measures load with: MAF+MAP (blended / torque model) (low confidence)
- 8Wideband sensorhardware
factory O2 type not yet sourced; plan on a Bosch LSU 4.9 for the GAINS ECU's built-in controller
- 9Bottom end and head sealingfactory reference
Reported: No reliable LT4-specific limit source found. (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
Drivetrain
Chassis integration
The ECM, TCM, body and chassis controllers are all on GM's CAN networks. Performance traction management, launch control and active rev-matching rely on the ECM torque model, so make sure calibration changes keep the torque estimates consistent.
Tuning notes
Smaller-pulley LT4 builds quickly reach the DI pump's limit. Log desired versus actual rail pressure at peak rpm before adding boost or ethanol. Heat soak through the integrated intercooler is the other common limit, so log intake air temperature with knock retard.
Popular swaps
Other Corvette C7 guides
GAINS on the Corvette C7
ECU2 + DI
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2 + DI; direct injection is handled by the DI driver. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Frequently asked
What ECU does the C7 Corvette use?
The E92 ECM, introduced with the Gen V LT1.4
What limits LT4 power in a ZL1 or Z06?
Mainly the cam-driven DI high-pressure pump, then the injectors. Upgraded pumps and DI injectors are the usual fixes.587
Does the C7 LT1 have AFM?
Yes. It deactivates cylinders 1, 4, 6 and 7 at light load.4
When did the Corvette get the 8L90?
For 2015. The Stingray offered the 8L90 eight-speed automatic alongside the seven-speed manual.2
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- 2014 Chevrolet Corvette Stingray Preliminary Specifications · Corvette Action Center · press · retrieved 2026-10-25
- 2015 Corvette Stingray to Offer Eight-Speed Automatic (GM press release) · General Motors (via Corvette Action Center) · oem · retrieved 2026-10-25
- 2015 Corvette Z06: LT4 Engine Overview (Source: GM Powertrain) · General Motors (via Corvette Action Center) · oem · retrieved 2026-10-25
- Is the Gen V Engine's Combustion System Really New? (Mike Magda, 2012-12-10) · EngineLabs · press · retrieved 2026-10-25
- L8T To The Party: Indirect Effects With Direct Injection · EngineLabs · press · retrieved 2026-10-25
- Chevrolet Performance Engine Controller Kits 19418585 (LT1) · JEGS · vendor-doc · retrieved 2026-10-25
- XDI High Flow LT4/LT5 Injectors (+30%) · Katech · vendor-doc · retrieved 2026-10-25
- Big Bore Direct Injection High Volume Fuel Pump for GM Gen V V8 Applications · Lingenfelter Performance Engineering · vendor-doc · retrieved 2026-10-25
- Chevrolet Performance 19433247 LT1 Wet Sump Engine Controller Kit (8/10-speed automatic, 2022+) · SDPC (Scoggin Dickey Parts Center) · vendor-doc · retrieved 2026-10-25
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- Factory ECU part numbers not yet sourced for this vehicle.
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)




