Honda · 1992-95

Honda Civic EG Si / VTi (D16Z6 / B16A) ECU and tuning guide

The Honda Civic EG Si / VTi (D16Z6 / B16A) (1992-95) runs the D16Y8 / D16Z6 / D15: 1.6 L I4, naturally aspirated, port injection, cable throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Honda Civic EG Si / VTi (D16Z6 / B16A), side view
Studio render for illustration, not a photograph of a specific car.
Years1988-00
Displacement1.6L
LayoutI4
InductionNaturally aspirated
InjectionPort injection
Cam controlVTECD16Z6/Y8
IgnitionDistributor
Swap demandMedium

Part of the Honda D-series family. B-swap chassis

Modeled power and torque

Modelled estimate, not a dyno result.

D16Y8 / D16Z6 / D15: stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
0501001502002500501001502001k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (127 hp at 6600 rpm, 107 lb-ft at 5500 rpm); the curve shape between peaks is modeled. Intake + exhaust + tune (pump fuel): Typical NA gains come mostly above mid-rpm.

D16Y8 / D16Z6 / D15 data

Platform background

The fifth-generation Civic (EG) is the archetypal OBD1 Honda tuning platform. The US Si hatch introduced VTEC to the Civic with the 125 hp D16Z6, and other markets got B16A2-powered VTi/SiR versions. B-series swaps use DC2 Integra-style mounts, and K-swaps use the Hasport EGK kit.

Factory ECU

US Si engine1.6-litre D16Z6 with VTEC on the intake cam, 125 hpSourced3
VTEC diagnostics (D16Z6)

The factory manual has dedicated spool-valve and oil-pressure-switch VTEC troubleshooting procedures

Sourced4
Diagnostics generationHonda OBD11992-95 ECU generationLow confidence5
B-series marketsB16A2 in Civic VTi/SiR versions outside the USLow confidence5

OBD1 ECUs from these years are the usual basis for chip/reflash tuning. Confirm the ECU's part-number family supports VTEC before using it with a VTEC engine.

Factory ECU: harness cross-reference

From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.

Honda OBD1 ECU (P28 / P30 / P72 / P05 etc.)Part numbers not yet sourced.
ECU family
Honda OBD1 37820-Pxx (1992-95)
Applies to
1992-95 Civic/Integra/Prelude, 1990-95 Accord; manual
Not for
automatic; OBD0 and OBD2 (1996+)

Honda part format 37820-<3-char engine code>-<rev>; code shown on ECU sticker (e.g. P28 = Civic EX/Si). Specific full part numbers not confirmed; A=US, J=Japan suffix convention per source.

Low confidenceUnverifiedE-1441
Honda OBD1 ECU (e.g. P28 / P30 / P72 / P75 class)Part numbers not yet sourced.
ECU family
Honda OBD1
Applies to
1992-95 Civic, Accord, Prelude; 1992-95 Integra (manual)
Not for
Not OBD2 (1996+); some Integra codes (P72/P75) exist in both OBD1 and OBD2 versions

One harness covers several OBD1 ECU part codes across Civic/Integra/Accord/Prelude; early 1992-93 Integra (DA) may be OBD0-style - verify. No OEM numbers verified from allowed sources.

Low confidenceUnverified

Factory ECU pinout

Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.

Honda OBD1 PGM-FI ECU (1992-95 Civic, 1994-95 Integra)

The 1992-95 Honda Civic and 1994-95 Acura Integra use a PGM-FI ECU (often called OBD1, e.g. P28, P72) with three harness plugs: A (26 cavities), B (16) and D (22), 64 cavities in all. A carries injectors, ignition output, relays and grounds; B carries power, distributor TDC/crank/cylinder pickups and switches; D carries sensors, 5 V supplies and diagnostics.

1992-1995 · USA / Canada (as documented); other markets not verified · 3 connectors, 64 cavities · 64 terminals sourced · ECU 37820-P28-A01, 37820-P06-A01, 37820-P72-A01, 37820-P75-A01

ECU connector A (C410 on 1994 Integra)26 cavities · 26 terminals listed · 26-cavity, two-row female harness plug (2 x 13), single latch at the top; Honda draws A1 at top left

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedDrawn as printed by Honda: the 1994 Integra manual p. 11-29 shows the ECM harness plugs C410/C408/C409 with a single outline (female terminals, which its legend says are viewed from the wire side), odd numbers on the top row ascending left to right, latch on top. A female plug seen from its wire side has the same handedness as looking into the ECM header, so this is recorded as ecu-side. The 1992 Civic terminal-location figures (pp. 11-13, 11-39) show the same A-B-D arrangement and numbering.
Honda OBD1 PGM-FI ECU (1992-95 Civic, 1994-95 Integra): ECU connector A (C410 on 1994 Integra)latchA1: Injector #1 (INJ1)A1A2: Injector #4 (INJ4)A2A3: Injector #2 (INJ2)A3A4: VTEC spool solenoid valve (VTS)A4A5: Injector #3 (INJ3)A5A6: Oxygen sensor heater control (HTCNTL)A6A7: PGM-FI main relay, fuel pump side (FLR1)A7A8: PGM-FI main relay, second feed (FLR2)A8A9: Idle air control valve (EACV)A9A10: Not usedA10A11: EGR control solenoid valve (ES)A11A12: Radiator fan control (FANC)A12A13: Check engine light (WARN)A13A14: Not usedA14A15: A/C compressor clutch relay (ACC)A15A16: Alternator control (ACGC)A16A17: A/T lock-up control solenoid valve B (ATLSB)A17A18: Not usedA18A19: A/T lock-up control solenoid valve A (ATLSA)A19A20: Purge cut-off solenoid valve (PGS)A20A21: Ignition output to igniter unit (IGP1, printed with a theta prefix)A21A22: Ignition output to igniter unit (IGP2, printed with a theta prefix)A22A23: Power ground (PG1)A23A24: Power ground (PG2)A24A25: Ignition power from PGM-FI main relay (IGP1)A25A26: Logic ground (LG1)A26
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
A1Injector #1 (INJ1)low-side injector driverBRNIntegra 1994: INJ1, BRN.
A2Injector #4 (INJ4)low-side injector driverYELIntegra 1994: INJ4, YEL (printed YEL1).
A3Injector #2 (INJ2)low-side injector driverREDIntegra 1994: INJ2, RED (printed RED1).
A4VTEC spool solenoid valve (VTS)low-side solenoid driverORN/WHTCivic 1992: used on D15Z1 and D16Z6 (VTEC) engines only. Integra 1994: VTEC solenoid valve (VT SOL), GRN/YEL, B18C1 (GS-R) only.
A5Injector #3 (INJ3)low-side injector driverLT BLUIntegra 1994: INJ3, BLU.
A6Oxygen sensor heater control (HTCNTL)low-side heater driverORN/BLKCivic 1992: heated O2 sensor heater (D15B7, D16Z6) or LAF sensor heater (D15Z1). Integra 1994: O2 sensor heater control (O2SHTC), ORN/BLK.
A7PGM-FI main relay, fuel pump side (FLR1)low-side relay driverGRN/YELIntegra 1994: FLR1, GRN/BLU.
A8PGM-FI main relay, second feed (FLR2)low-side relay driverGRN/YELCivic 1992 shows A7 and A8 joined to the main relay. Integra 1994: no wire ("—").
A9Idle air control valve (EACV)idle air valve driverGRN/WHTIntegra 1994: IAC valve (IACV), BLK/BLU.
A10Not usedOther / not used—No ECU wire at this cavity on the 1992 Civic schematic (pp. 11-12 to 11-18) or in the 1994 Integra C410 table ("—").
A11EGR control solenoid valve (ES)low-side solenoid driverORN/BLUCivic 1992: D15Z1 engine only. Integra 1994: no wire ("—").
A12Radiator fan control (FANC)low-side relay driverYEL/GRNIntegra 1994: FANC, GRN (to radiator fan relay and condenser fan relay).
A13Check engine light (WARN)lamp driverGRN/ORNIntegra 1994: malfunction indicator lamp (MIL), GRN/ORN.
A14Not usedOther / not used—No ECU wire at this cavity on the 1992 Civic schematic (pp. 11-12 to 11-18) or in the 1994 Integra C410 table ("—").
A15A/C compressor clutch relay (ACC)low-side relay driverBLK/REDIntegra 1994: ACC, BLK/RED.
A16Alternator control (ACGC)alternator control output—Civic 1992 p. 11-15 prints WHT/YEL and PNK beside one A16 label and the D9 label is missing there, so the wire colour of A16 versus D9 cannot be assigned from the figure. Integra 1994: alternator control (ALT C), WHT/GRN. (medium confidence)
A17A/T lock-up control solenoid valve B (ATLSB)low-side solenoid driverGRN/BLKCivic 1992: A/T only. Integra 1994: IAB control solenoid valve (IAB CS), PNK/BLU, B18C1 only.
A18Not usedOther / not used—No ECU wire at this cavity on the 1992 Civic schematic (pp. 11-12 to 11-18) or in the 1994 Integra C410 table ("—").
A19A/T lock-up control solenoid valve A (ATLSA)low-side solenoid driverYELCivic 1992: A/T only. Integra 1994: FAS signal to the TCM, YEL (printed YEL2), B18B1 A/T only.
A20Purge cut-off solenoid valve (PGS)low-side solenoid driverREDIntegra 1994: EVAP purge control solenoid valve (PCS), RED (printed RED2).
A21Ignition output to igniter unit (IGP1, printed with a theta prefix)igniter trigger outputRED/GRNCivic 1992: A21 and A22 are joined and run to the igniter unit. Integra 1994: ignition control module output (ICM 1), YEL/GRN.
A22Ignition output to igniter unit (IGP2, printed with a theta prefix)igniter trigger outputRED/GRNCivic 1992: joined with A21 to the igniter unit. Integra 1994: no wire ("—").
A23Power ground (PG1)power groundBLKIntegra 1994: PG1, BLK (printed BLK1).
A24Power ground (PG2)power groundBLKIntegra 1994: PG2, BLK (printed BLK2).
A25Ignition power from PGM-FI main relay (IGP1)12 V switched supplyYEL/BLKIntegra 1994: IGP1, YEL/BLK.
A26Logic ground (LG1)logic groundBLK/REDIntegra 1994: LG1, BRN/BLK.

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECU connector B (C408 on 1994 Integra)16 cavities · 16 terminals listed · 16-cavity, two-row female harness plug (2 x 8), single latch at the top; Honda draws B1 at top left

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedDrawn as printed by Honda: the 1994 Integra manual p. 11-29 shows the ECM harness plugs C410/C408/C409 with a single outline (female terminals, which its legend says are viewed from the wire side), odd numbers on the top row ascending left to right, latch on top. A female plug seen from its wire side has the same handedness as looking into the ECM header, so this is recorded as ecu-side. The 1992 Civic terminal-location figures (pp. 11-13, 11-39) show the same A-B-D arrangement and numbering.
Honda OBD1 PGM-FI ECU (1992-95 Civic, 1994-95 Integra): ECU connector B (C408 on 1994 Integra)latchB1: Ignition power from PGM-FI main relay (IGP2)B1B2: Logic ground (LG2)B2B3: A/T shift position D3 signal (ATD3)B3B4: A/T shift position D4 signal (ATD4)B4B5: A/C switch signal (ACS)B5B6: Not usedB6B7: Clutch switch (CLSW, M/T) or A/T park/neutral position (ATNP)B7B8: Power steering oil pressure switch (PSW)B8B9: Starter signal (STS)B9B10: Vehicle speed sensor (VSP)B10B11: Cylinder (CYL) sensor + (CYL P)B11B12: Cylinder (CYL) sensor - (CYL M)B12B13: TDC sensor + (TDC P)B13B14: TDC sensor - (TDC M)B14B15: Crank sensor + (CRNK P)B15B16: Crank sensor - (CRNK M)B16
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
B1Ignition power from PGM-FI main relay (IGP2)12 V switched supplyYEL/BLKIntegra 1994: IGP2, YEL/BLK.
B2Logic ground (LG2)logic groundBRN/BLKIntegra 1994: LG2, BRN/BLK.
B3A/T shift position D3 signal (ATD3)switch inputGRN/BLUCivic 1992: A/T only, from the shift position console switch. Integra 1994: A/T FI signal A (AFSA) from the TCM, GRN/BLU, B18B1 only.
B4A/T shift position D4 signal (ATD4)switch inputGRN/BLKCivic 1992: A/T only. Integra 1994: A/T FI signal B (AFSB) from the TCM, GRY, B18B1 only.
B5A/C switch signal (ACS)switch inputBLU/REDIntegra 1994: ACS, BLU/RED.
B6Not usedOther / not used—No ECU wire at this cavity on the 1992 Civic schematic (pp. 11-12 to 11-18) or in the 1994 Integra C408 table ("—").
B7Clutch switch (CLSW, M/T) or A/T park/neutral position (ATNP)switch input—Civic 1992: M/T clutch switch, PNK/BLK, D15Z1 only; A/T park/neutral, GRN. Integra 1994: A/T park/neutral (ATP PN), LT GRN/BLK, B18B1 only. (medium confidence)
B8Power steering oil pressure switch (PSW)switch inputBRN/REDIntegra 1994: PSP SW, GRN.
B9Starter signal (STS)12 V input while crankingBLU/WHTIntegra 1994: STS, BLU/WHT.
B10Vehicle speed sensor (VSP)pulse inputYEL/BLUIntegra 1994: VSS, ORN (printed ORN1).
B11Cylinder (CYL) sensor + (CYL P)inductive pickup +ORNIntegra 1994: CYP P, ORN (printed ORN2). Sensor sits in the distributor (TDC/CKP/CYP sensor assembly).
B12Cylinder (CYL) sensor - (CYL M)inductive pickup -WHTIntegra 1994: CYP M, WHT.
B13TDC sensor + (TDC P)inductive pickup +ORN/BLUIntegra 1994: TDC P, ORN/BLU.
B14TDC sensor - (TDC M)inductive pickup -WHT/BLUIntegra 1994: TDC M, WHT/BLU.
B15Crank sensor + (CRNK P)inductive pickup +BLU/GRNIntegra 1994: CKP P, BLU/GRN.
B16Crank sensor - (CRNK M)inductive pickup -BLU/YELIntegra 1994: CKP M, BLU/YEL.

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

ECU connector D (C409 on 1994 Integra)22 cavities · 22 terminals listed · 22-cavity, two-row female harness plug (2 x 11), single latch at the top; Honda draws D1 at top left

Looking into the ECU's connector. The harness plug seen from its wire side has the same layout.

How the OEM figure is orientedDrawn as printed by Honda: the 1994 Integra manual p. 11-29 shows the ECM harness plugs C410/C408/C409 with a single outline (female terminals, which its legend says are viewed from the wire side), odd numbers on the top row ascending left to right, latch on top. A female plug seen from its wire side has the same handedness as looking into the ECM header, so this is recorded as ecu-side. The 1992 Civic terminal-location figures (pp. 11-13, 11-39) show the same A-B-D arrangement and numbering.
Honda OBD1 PGM-FI ECU (1992-95 Civic, 1994-95 Integra): ECU connector D (C409 on 1994 Integra)latchD1: Back-up power, constant battery (VBU)D1D2: Brake switch (BKSW)D2D3: LAF sensor label resistor (LABEL)D3D4: Service check connector (SCS)D4D5: Not usedD5D6: Valve timing oil pressure switch (VTM)D6D7: Data link connector (TXD/RXD)D7D8: LAF sensor VS+ (VS+)D8D9: Alternator FR signal (ACGF)D9D10: Electrical load detector (EL)D10D11: Throttle angle sensor signal (TH, printed with a theta prefix)D11D12: EGR valve lift sensor (EGRL)D12D13: Coolant temperature sensor (TW)D13D14: Oxygen sensor signal (O2), or LAF sensor IP+ on D15Z1D14D15: Intake air temperature sensor (TA)D15D16: LAF sensor IP- / VS- (IP-, VS-)D16D17: MAP sensor signal (PB)D17D18: Shift-up indicator (SIL, M/T) or A/T interlock control (SLU)D18D19: Sensor 5 V supply 1 (VCC1)D19D20: Sensor 5 V supply 2 (VCC2)D20D21: Sensor ground 1 (SG1)D21D22: Sensor ground 2 (SG2)D22
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
D1Back-up power, constant battery (VBU)12 V constant supplyWHT/BLUFed through the BACK UP (7.5 A) fuse. Integra 1994: VBU, WHT/BLU.
D2Brake switch (BKSW)12 V switch inputGRN/WHTIntegra 1994: BKSW, GRN/WHT (printed GRN/WHT1).
D3LAF sensor label resistor (LABEL)analog inputBLU/YELCivic 1992: D15Z1 (LAF sensor) only. Integra 1994: knock sensor (KS), RED/BLU, B18C1 only.
D4Service check connector (SCS)diagnostic inputBRNIntegra 1994: SCS, BRN/WHT.
D5Not usedOther / not used—No ECU wire at this cavity on the 1992 Civic schematic (pp. 11-12 to 11-18) or in the 1994 Integra C409 table ("—").
D6Valve timing oil pressure switch (VTM)switch inputORN/BLUCivic 1992: D15Z1 and D16Z6 only. Integra 1994: VTEC pressure switch (VTP SW), BLU/BLK, B18C1 only.
D7Data link connector (TXD/RXD)serial dataLT BLUIntegra 1994: TXD/RXD, LT BLU.
D8LAF sensor VS+ (VS+)LAF sensor signalWHT/BLUCivic 1992: D15Z1 only. Integra 1994: barometric pressure output to the TCM (BARO OUT), LT GRN, B18B1 A/T only.
D9Alternator FR signal (ACGF)analog input—See A16: the Civic 1992 figure does not print a separate D9 wire colour. Integra 1994: ALT F, WHT/RED (printed WHT/RED1). (medium confidence)
D10Electrical load detector (EL)analog inputGRN/REDIntegra 1994: ELD, GRN/RED (Integra figure marks the ELD as USA only).
D11Throttle angle sensor signal (TH, printed with a theta prefix)0-5 V analogLT GRNIntegra 1994: TPS, RED/BLK.
D12EGR valve lift sensor (EGRL)0-5 V analogWHT/BLKCivic 1992: D15Z1 only. Integra 1994: no wire ("—").
D13Coolant temperature sensor (TW)thermistor inputRED/WHTIntegra 1994: ECT, RED/WHT.
D14Oxygen sensor signal (O2), or LAF sensor IP+ on D15Z1O2 / LAF signal—Civic 1992: WHT for the O2 sensor (D15B8) and heated O2 sensor (D15B7, D16Z6); ORN/BLU for the LAF sensor IP+ (D15Z1). Integra 1994: O2S, WHT/RED (printed WHT/RED2). (medium confidence)
D15Intake air temperature sensor (TA)thermistor inputRED/YELIntegra 1994: IAT, RED/YEL.
D16LAF sensor IP- / VS- (IP-, VS-)LAF sensor signalBLU/GRNCivic 1992: D15Z1 only. Integra 1994: VREF to the TCM, WHT/BLK, B18B1 only.
D17MAP sensor signal (PB)0-5 V analogWHTIntegra 1994: MAP (PB), WHT/YEL.
D18Shift-up indicator (SIL, M/T) or A/T interlock control (SLU)low-side driver—Civic 1992: SIL to the shift-up indicator light, PNK/GRN (M/T); SLU to the interlock control unit, WHT/RED (A/T). Integra 1994: no wire ("—"). (medium confidence)
D19Sensor 5 V supply 1 (VCC1)5 V referenceYEL/GRNCivic 1992: MAP sensor supply. Integra 1994: VCC1, YEL/WHT.
D20Sensor 5 V supply 2 (VCC2)5 V referenceYEL/WHTCivic 1992: throttle angle sensor supply. Integra 1994: VCC2, YEL/BLU.
D21Sensor ground 1 (SG1)sensor groundGRN/BLUIntegra 1994: SG1, GRN/WHT (printed GRN/WHT2).
D22Sensor ground 2 (SG2)sensor groundGRN/WHTIntegra 1994: SG2, GRN/BLU.

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

Pin rows follow the 1992 Civic (USA/Canada) manual, which covers the D15B7, D15B8, D15Z1 and D16Z6 engines; each row's notes give the 1994 Integra (B18B1 / B18C1) function and wire colour. Both manuals use the same A-B-D layout and numbering, and the core circuits (power, grounds, injectors, TDC/crank/cylinder pickups, sensor supplies) sit on the same cavities. Model-specific pins (VTEC, knock, IAB, LAF sensor, A/T) differ.

There is no connector C on these ECUs: Honda's terminal-location figures draw a shaded, unnumbered block between B and D. Wire colours differ between Civic and Integra harnesses on many pins (for example A26 is BLK/RED on the Civic and BRN/BLK on the Integra), so check the colour against your own car.

Not verified here: 1993-95 Civic and 1993-95 del Sol changes after the 1992 manual, the B16A Civic VTi (non-US), JDM and European ECUs, and 1995 Integra changes after the 1994 manual. The Integra GS-R parts listing covers both 1994 and 1995 with the same ECU number.

Year split for the DC2 Integra catalog rows (1994-2001): only 1994-95 use this A-B-D ECU. The 1998 Integra manual lists the ECM harness plugs as ECM-A, ECM-C and ECM-D, a different set, so 1996-2001 cars (including the Type R) are outside this page.

Safety: disconnect the battery negative before unplugging or wiring the ECU, and wait as the manual's ECU procedures direct. The 1992 Civic and 1994 Integra manuals test at the ECU with a test harness between the ECU and its plugs; do not force sharp probes into the plug cavities, which can spread the female terminals.

All factory ECU pinouts →

Plug-and-play harness

Route for this carS3 plug-in harness
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.

MakerHarnessFitsLink
Nexus S2/S3 Plug n Play Adapter Harness Honda OBD-IHT-1863311992-95 Civic/Integra/Prelude, 1990-95 Accord; manual$495LowestMaker ↗
Manual 1992 - 1995 Acura IntegraBF29002-S31992-95 Civic, Accord, Prelude; 1992-95 Integra (manual)$840Maker ↗
Wire-inUniversal flying lead or re-terminated factory harnessAny engine (terminate to ECU2's two Superseal 34 connectors)Universal harness from $405Maker ↗

Nexus S2/S3 Plug n Play Adapter Harness Honda OBD-I

$495USD list · excl. tax · unconfirmed
Plug-and-playManual onlyOff-road / competition onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Honda OBD1 ECU (P28 / P30 / P72 / P05 etc.)
ECU
Honda OBD1 37820-Pxx (1992-95)
Confidence
low

Honda part format 37820-<3-char engine code>-<rev>; code shown on ECU sticker (e.g. P28 = Civic EX/Si). Specific full part numbers not confirmed; A=US, J=Japan suffix convention per source.

Sources: E-1441

Fits
1992-95 Civic/Integra/Prelude, 1990-95 Accord; manual
Exclusions
automatic; OBD0 and OBD2 (1996+)
SKU
HT-186331
Maker fitment
Honda OBD-I: 1992-95 Civic/Integra/Prelude and 1990-95 Accord; manual only
Maker notes
(search snippet); kit HT-213300

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1992 - 1995 Acura Integra

$840USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Honda OBD1 ECU (e.g. P28 / P30 / P72 / P75 class)
ECU
Honda OBD1
Confidence
low

One harness covers several OBD1 ECU part codes across Civic/Integra/Accord/Prelude; early 1992-93 Integra (DA) may be OBD0-style - verify. No OEM numbers verified from allowed sources.

Fits
1992-95 Civic, Accord, Prelude; 1992-95 Integra (manual)
Exclusions
Not OBD2 (1996+); some Integra codes (P72/P75) exist in both OBD1 and OBD2 versions
SKU
BF29002-S3
Maker fitment
Acura Integra; Honda Accord; Honda Civic; Honda Prelude (Manual); selector years 1992-1995; SKU label: Manual 1992 - 1995 Acura Integra
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); USDM selector

Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.

Your GAINS system for this car · pre-release

ECU2 for the Civic EG

Planned with the same rules as the configurator for this car's 4 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

Honda Civic EG Si / VTi (D16Z6 / B16A) studio render
Civic EG
  • ECU2Engine controller

    4 cyl · port injection · cable throttle

    Runs this 4-cylinder's injectors and its distributor on one ignition output, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harness1 listed · from $495 USD listHT-186331
  2. Factory-connector → S3 adapter1 listed · from $840 USD list
  3. Wire-inAlways possible

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Civic EG

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    VTEC crossoverplanned

    VTEC engagement is treated as a load and rpm surface where the two cam profiles cross on torque, learned from logs rather than a single fixed rpm.

  4. 4
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  5. 5
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAP speed-density (medium confidence)

  6. 6
    Wideband sensorhardware

    factory sensor type changes by year/market (narrowband on earlier cars); fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller either way

  7. 7
    Bottom end and head sealingfactory reference

    Reported: Ring lands of the stock pistons are commonly reported (forum) as the first failure under boost; an Edelbrock turbo-kit install sheet reportedly calls ~7-8 psi typical for a healthy stock D16Y8 and recommends aftermarket pistons, rods and valves above that (search excerpt; PDF returned 403 on fetch). (low confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Drivetrain

Si transmission5-speed manualSourced3

Chassis integration

Brakes and safety
  • Four-wheel disc brakes on the Si
  • Dual front airbags standard from 1994 with optional ABS
Sourced3

Tuning notes

B-series swaps into the EG use the DC2 Integra mounting arrangement. Wiring is simplest with an OBD1 B-series engine harness matched to the OBD1 chassis. The VTEC solenoid and pressure-switch circuits must reach a VTEC-capable ECU.

Popular swaps

B-series mounts

Hasport DCSTK (3-bolt timing-side bracket, hydraulic transmission) or EGSTK (2-bolt bracket) for 92-95 Civic

Sourced · medium1
K-series mounts
  • Hasport EGK, dual-height
  • Requires removing the stock transmission bracket from the frame rail
Sourced · medium2

GAINS on the Civic EG

ECU2

ECU2Runs this 4-cylinder's injectors and its distributor on one ignition output, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

Is the 92-95 Civic OBD1?

Yes, it uses Honda's OBD1 ECU generation.5

What engine was in the 1992-95 Civic Si?

The D16Z6 1.6-litre SOHC VTEC, rated at 125 hp.3

What mounts do I need to B-swap an EG?

A DC2 Integra-pattern kit such as Hasport's DCSTK (3-bolt bracket, hydraulic transmission) or EGSTK (2-bolt bracket).1

Can you K-swap an EG Civic?

Yes. Hasport's EGK kit covers 92-95 Civic with transmission-specific versions.2

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. DCSTK B-Series Mount Kit (94-01 Integra) · Hasport Performance · vendor-doc · retrieved 2026-10-25
  2. EGK K-Series Mount Kit (92-95 Civic, 94-01 Integra, Del Sol) · Hasport Performance · vendor-doc · retrieved 2026-10-25
  3. Honda Civic Si Timeline and Milestones · American Honda Motor Co. (hondanews.com) · press · retrieved 2026-10-25
  4. Honda Civic 1992-1995 Service Manual (table of contents as hosted by ManualsLib) · American Honda Motor Co. (hosted by ManualsLib) · service-manual · retrieved 2026-10-25
  5. Honda B engine · Wikipedia · community · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  • Catalog note: B-swap chassis
  1. E-911 Haltech S3 adapter harness page (sourced, high confidence)
  2. E-934 Boomslang identity (sourced, high confidence)
  3. E-935 Boomslang S3 catalog size (sourced, high confidence)
  4. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  5. E-941 S3 engine harness availability (inferred, medium confidence)
  6. E-1441 Honda OBD1 ECU codes (reported, low confidence)