Engine: VG30DE(TT) (Z32)
Part of the Nissan VG30 family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (300 hp at 6400 rpm, 283 lb-ft at 3600 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.
VG30DE(TT) (Z32) data
- Load sensing
- MAF (hot-wire / hot-film)
- O2 sensor
- narrowband (zirconia)
- Closed loop
- narrowband closed loop at stoich; open loop decel/accel, high load/high speed, (1996: also idle), cold/failed sensor (Nissan FSM)
- Block
- cast iron
- Rods / pistons
- forged steel (MotoIQ) · oil-cooled by block-mounted sprayers (MotoIQ)
- Reported limit
- author suggests ~700 hp or less for extended racing on block (MotoIQ comment)
- Factory
- Nissan/JECS side-feed
- Impedance
- high (saturated)
- Direct-fit upgrades
- 4 maker-listed
- Knock
- 22060-30P00
- MAP / MAF
- 22680-30P00|22680-16V00 (alt OE in listing)
- O2 (upstream)
- narrowband zirconia
Factory ECU
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Nissan 23710-series ECCS
- Applies to
- Z32 300ZX 1990-95 (VG30DE/VG30DETT); manual
- Not for
- 1996 OBD2; automatic
No source-supported part number found.
- ECU family
- Nissan ECCS, Z32 VG30DETT
- Applies to
- 1990-1995 300ZX Twin Turbo, manual; USDM
- Not for
- non-turbo VG30DE; automatic
23710-30P (queried) not confirmed by any source; left blank. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
- ECU family
- Nissan ECCS, A32 Maxima VQ30DE
- Applies to
- 1995-1999 Maxima (A32) SE/GXE, manual; USDM
- Not for
- automatic
41U10 / 41U70 listed for 1995 Maxima VQ30DE (transmission not stated); example only. Boomslang fitment also lists 300ZX Turbo under this SKU: ambiguity. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
Factory ECU pinout: pending
No OEM pin table is in our library yet for the VG30DE(TT) (Z32) factory ECU. We only publish pinouts drawn from the OEM service manual or the maker's own documents, and none has been sourced yet. Until then, wire from the harness maker's instructions or the factory service manual.
Plug-and-play harness
A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
| Nissan 300ZX Z32HT-186361 | Z32 300ZX 1990-95 (VG30DE/VG30DETT); manual | $535Lowest | Maker ↗ | |
![]() | Manual 1990 - 1995 Nissan 300ZX TurboBF29091-S3 | 1990-1995 300ZX Twin Turbo, manual; USDM | $840 | Maker ↗ |
![]() | Manual 1995 - 1999 Nissan MaximaBF29092-S3 | 1995-1999 Maxima (A32) SE/GXE, manual; USDM | $840 | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |
Nexus S3 Plug n Play Adapter Harness Nissan 300ZX Z32
- Plugs into
Nissan 300ZX Z32 ECCS ECU (OBD1)
- ECU
- Nissan 23710-series ECCS
- Confidence
- low
No source-supported part number found.
- Fits
- Z32 300ZX 1990-95 (VG30DE/VG30DETT); manual
- Exclusions
- 1996 OBD2; automatic
- SKU
- HT-186361
- Maker fitment
- Nissan 300ZX Z32 OBD1 (1990-95); manual only
- Maker notes
- kit HT-213319

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1990 - 1995 Nissan 300ZX Turbo
- Plugs into
ECCS ECU (VG30DETT, Z32 300ZX Twin Turbo)
- ECU
- Nissan ECCS, Z32 VG30DETT
- Confidence
- low
23710-30P (queried) not confirmed by any source; left blank. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
- Fits
- 1990-1995 300ZX Twin Turbo, manual; USDM
- Exclusions
- non-turbo VG30DE; automatic
- SKU
- BF29091-S3
- Maker fitment
- Nissan 300ZX Turbo (Manual); selector years 1990-1995; SKU label: Manual 1990 - 1995 Nissan 300ZX Turbo
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 1990-95

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1995 - 1999 Nissan Maxima
- Plugs into
ECCS ECM (VQ30DE, A32 Maxima 1995-99) · 23710-41U10, 23710-41U70
- OEM part numbers
- 23710-41U10, 23710-41U70
- ECU
- Nissan ECCS, A32 Maxima VQ30DE
- Confidence
- low
41U10 / 41U70 listed for 1995 Maxima VQ30DE (transmission not stated); example only. Boomslang fitment also lists 300ZX Turbo under this SKU: ambiguity. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
Sources: E-1486
- Fits
- 1995-1999 Maxima (A32) SE/GXE, manual; USDM
- Exclusions
- automatic
- SKU
- BF29092-S3
- Maker fitment
- Nissan 300ZX Turbo; Nissan Maxima (Manual); selector years 1995-1999; SKU label: Manual 1995 - 1999 Nissan Maxima
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 1996 300ZX shares Maxima-numbered SKU in selector
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the 300ZX Z32
Planned with the same rules as the configurator for this car's 6 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.
- Price TBA
ECU2Engine controller
6 cyl · port injection · cable throttle
Full sequential fuel and spark for this 6-cylinder on a cable throttle, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harness1 listed · from $535 USD listHT-186361
- Factory-connector → S3 adapter2 listed · from $840 USD list
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
Swap guides
Into the 300ZX Z32
How GAINS approaches the 300ZX Z32
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3Cam phasing (VVT)gated
Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.
- 4Boost controlgated
A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.
- 5Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 6Factory load sensingfactory reference
What the factory ECU measures load with: MAF (hot-wire / hot-film) (high confidence)
- 7Wideband sensorhardware
Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller
- 8Bottom end and head sealingfactory reference
Reported: MotoIQ notes thin cylinder walls (sonic-test beyond ~0.5 mm overbore) and core shift restricting coolant so rear cylinders run hot and detonate first. (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
GAINS on the 300ZX Z32
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-924 Haltech S3 adapter harness page (sourced, high confidence)
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)
- E-1486 harness ECU xref: Nissan Maxima 1995 VQ30DE (verified, low confidence)


