Engine: SR20DET (red / black top, S15)
Part of the Nissan SR20 family.
Modeled power and torque
Modelled estimate, not a dyno result.
Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.
Stock is anchored to the factory rating (247 hp at 6400 rpm, 203 lb-ft at 4800 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.
SR20DET (red / black top, S15) data
- Load sensing
- MAF (hot-wire / hot-film)
- O2 sensor
- narrowband (zirconia)
- Closed loop
- narrowband closed loop at idle/cruise only, open loop under load/WOT (inferred from Nissan ECCS FSM text for SR20DE/KA24DE)
- Block
- aluminium
- Rods / pistons
- cast (ring lands cited as weak); oil squirters on turbo SR20 (forum)
- Reported limit
- ~400 whp on stock internals commonly claimed (forum); a shop guide suggests sleeves above ~500 hp (Brewed Motorsports)
- Factory
- Nissan/JECS side-feed
- Impedance
- high (saturated)
- Direct-fit upgrades
- 6 maker-listed
- Knock
- 22060-30P00
- MAP / MAF
- hot-wire, analog 0-5 V
- O2 (upstream)
- narrowband zirconia
Platform background
The S14 (1993-1998) was sold as the Silvia in Japan and 200SX in Europe with the SR20DET (220 PS in Japanese K's form), and as the 240SX in North America with the KA24DE. The S14 SR20DET adds an on/off VTC solenoid, an ECU-controlled wastegate solenoid and a boost pressure sensor. This page gives Nissan factory ECM terminal data for both the export S14 SR20DET (partial) and the 1997 US 240SX KA24DE (complete, with wire colours).
Factory ECU
MAF load, VTC solenoid, wastegate control solenoid, boost pressure sensor, single knock sensor
Sourced3OBD-II ECM with GST and CONSULT data link, front and rear heated O2 sensors, OBD crankshaft position sensor, EVAP monitoring
Sourced1The export SR20DET ECM is a pre-OBD-II ECCS unit with CONSULT diagnostics, whereas the US 240SX KA24DE ECM is a full OBD-II unit with EVAP, rear O2 and misfire monitoring. US SR20DET swaps therefore lose OBD-II readiness functions unless a compliant solution is used; check local inspection rules.
Factory ECU: harness cross-reference
From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.
- ECU family
- Nissan 23710-series ECCS
- Applies to
- S14 Silvia series 1 (Zenki, 1993-96); manual
- Not for
- S14A Kouki (use HT-186341); automatic
- Supplier
- Hitachi
No part number confirmed; supplier Hitachi per general Nissan ECCS convention, not source-confirmed for this unit (leave unverified).
- ECU family
- Nissan 23710-series ECCS (64-pin header)
- Applies to
- S15 ADM/JDM; S14A Kouki; 180SX Type X 1996+; Pulsar N14/N15 SSS & GTI-R; Micra K11; manual
- Not for
- S13/S14 Zenki (76-pin, separate harnesses); automatic
S15 examples only (23710-91F**); 91F01 vs 91F05 interchange questioned (NATS/JDM-ADM). Harness spans many different OEM ECUs sharing one connector type; part numbers for N14/N15/K11/Kouki not gathered.
- ECU family
- Nissan ECCS, S14 SR20DET
- Applies to
- 1993-1998 S14 Silvia SR20DET, manual; JDM (and EDM 200SX variants)
- Not for
- automatic
Numbers from forum posts only (80F00 1996-98 S14 SR20DET M/T; 0A547 S14 SR20DET M/T 09/97-12/98). S14 and S14a (kouki) ECUs differ; harness covers both per year range. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
- ECU family
- Nissan ECCS, S15 SR20DET
- Applies to
- 1999-2002 S15 Silvia Spec R (6MT); Boomslang selector also lists S14 SR20DET 1997-98
- Not for
- automatic; Spec S (SR20DE NA)
Forum suggestions (23710-85F04 / 23710-91F**) unconfirmed; left blank. Boomslang fitment lists both S14 and S15 under this SKU: ambiguity, owner should check connector/ECU.
Factory ECU pinout
Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.
Nissan Silvia / 200SX (S14) SR20DET ECM, 1994 LHD export
The Nissan Silvia / 200SX (S14) SR20DET ECM, 1994 LHD export uses 1 connector with 76 cavities. This page draws each face from the OEM figure and lists the 30 terminals the OEM table documents, with wire colours where the manual prints them.
1994 on (LHD export manual) · Europe (LHD export) · 1 connector, 76 cavities · 30 terminals sourced
Looking into the harness plug's mating face (mirror of the ECU face).
How the OEM figure is oriented
Harness side (looking into the plug), as drawn in the OEM figure.| Pin | Function | Type | Wire | Notes |
|---|---|---|---|---|
| 19 | Cooling fan (low speed) | Outputs | — | |
| 23 | Knock sensor | Sensor signal | — | |
| 25 | Wastegate valve control solenoid valve | Outputs | — | |
| 27 | Mass air flow sensor | Sensor signal | — | |
| 28 | Engine coolant temperature sensor | Sensor signal | — | |
| 29 | Heated oxygen sensor | Sensor signal | — | |
| 33 | Cooling fan (high speed) | Outputs | — | |
| 34 | Power steering oil pressure switch | Sensor signal | — | |
| 35 | Boost pressure sensor | Sensor signal | — | |
| 38 | Throttle position sensor | Sensor signal | — | |
| 41 | Camshaft position sensor reference signal | Crank / cam | — | |
| 42 | Camshaft position sensor position signal | Crank / cam | — | |
| 43 | Start signal | Sensor signal | — | |
| 44 | Neutral position switch (M/T) / A/T control unit (A/T) | Sensor signal | — | |
| 45 | Ignition switch | Power | — | |
| 46 | Air conditioner switch | Sensor signal | — | |
| 48 | Power source for sensors (5 V) | Sensor 5 V / ground | — | |
| 49 | Power source for ECM | Power | — | |
| 51 | Camshaft position sensor reference signal | Crank / cam | — | |
| 52 | Camshaft position sensor position signal | Crank / cam | — | |
| 54 | Load signal (rear window defogger) | Sensor signal | — | |
| 58 | Power supply (back-up) | Power | — | |
| 59 | Power source for ECM | Power | — | |
| 101 | Injectors (individual cylinder assignment not given in this table) (shared group 101, 103, 110, 112) | Injector | — | |
| 102 | EGR and canister control solenoid valve | Outputs | — | |
| 103 | Injectors (individual cylinder assignment not given in this table) (shared group 101, 103, 110, 112) | Injector | — | |
| 110 | Injectors (individual cylinder assignment not given in this table) (shared group 101, 103, 110, 112) | Injector | — | |
| 112 | Injectors (individual cylinder assignment not given in this table) (shared group 101, 103, 110, 112) | Injector | — | |
| 113 | VTC solenoid valve | Outputs | — | |
| 115 | Heated oxygen sensor heater | Outputs | — |
Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.
Coverage, year splits and safety
Covers the SR20DET ECM in Nissan's 1994 S14 service manual (LHD export, 200SX). JDM Silvia (zenki/kouki) ECUs and later model years were not checked against their own manuals; confirm terminal use on your ECU before wiring.
Source notes: SR20DET rows come from the Nissan Model S14 Series Service Manual (1994, LHD export) ECM input/output signal inspection table; the scanned copy is missing page EC-197 (terminals 1-18 including ignition and injector-to-cylinder assignment), so those rows are absent and must be taken from a complete copy of the manual or the S14 wiring diagram. KA24DE rows (with terminal-side wire colours) come from the 1997 Nissan 240SX service manual EC section, ECM inspection table.
Safety: disconnect the battery before working on the ECU harness, and confirm each terminal with a meter against your own car's manual before cutting or pinning wires.
Plug-and-play harness
A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.
| Maker | Harness | Fits | Link | |
|---|---|---|---|---|
| Nexus S2/S3 Plug n Play Adapter Harness Nissan Silvia S14 S1 ZENKIHT-186333 | S14 Silvia series 1 (Zenki, 1993-96); manual | $535Lowest | Maker ↗ | |
| Nexus S2/S3 Plug n Play Adapter Harness Nissan Silvia S15HT-186341 | S15 ADM/JDM; S14A Kouki; 180SX Type X 1996+; Pulsar N14/N15 SSS & GTI-R; Micra K11; manual | $535Lowest | Maker ↗ | |
![]() | Manual 1993 - 1996 Nissan Silvia S14 SR20DETBF29060-S3 | 1993-1998 S14 Silvia SR20DET, manual; JDM (and EDM 200SX variants) | $840 | Maker ↗ |
![]() | Manual 1998 - 2002 Nissan Silvia S15 SR20DETBF29061-S3 | 1999-2002 S15 Silvia Spec R (6MT); Boomslang selector also lists S14 SR20DET 1997-98 | $840 | Maker ↗ |
| Wire-in | Universal flying lead or re-terminated factory harness | Any engine (terminate to ECU2's two Superseal 34 connectors) | Universal harness from $405 | Maker ↗ |
Nexus S2/S3 Plug n Play Adapter Harness Nissan Silvia S14 S1 ZENKI
- Plugs into
Nissan ECCS ECU, S14 Zenki SR20DET
- ECU
- Hitachi · Nissan 23710-series ECCS
- Confidence
- low
No part number confirmed; supplier Hitachi per general Nissan ECCS convention, not source-confirmed for this unit (leave unverified).
- Fits
- S14 Silvia series 1 (Zenki, 1993-96); manual
- Exclusions
- S14A Kouki (use HT-186341); automatic
- SKU
- HT-186333
- Maker fitment
- Nissan Silvia S14 series 1 (Zenki); manual only
- Maker notes
- kit HT-213304; Zenki (early S14) only; Kouki is HT-186341
Nexus S2/S3 Plug n Play Adapter Harness Nissan Silvia S15
- Plugs into
Nissan ECCS ECU, SR20DE(T) 64-pin (S15 / S14A Kouki / N15 / K11) · 23710-91F01, 23710-91F05
- OEM part numbers
- 23710-91F01, 23710-91F05
- ECU
- Nissan 23710-series ECCS (64-pin header)
- Confidence
- low
S15 examples only (23710-91F**); 91F01 vs 91F05 interchange questioned (NATS/JDM-ADM). Harness spans many different OEM ECUs sharing one connector type; part numbers for N14/N15/K11/Kouki not gathered.
- Fits
- S15 ADM/JDM; S14A Kouki; 180SX Type X 1996+; Pulsar N14/N15 SSS & GTI-R; Micra K11; manual
- Exclusions
- S13/S14 Zenki (76-pin, separate harnesses); automatic
- SKU
- HT-186341
- Maker fitment
- Nissan 200SX/Silvia S15 (ADM, JDM), S14A Kouki, 180SX Type X 1996+, Pulsar N15/N14 SSS and GTI-R, Micra K11; manual only

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1993 - 1996 Nissan Silvia S14 SR20DET
- Plugs into
ECCS ECU (SR20DET, S14 Silvia / 200SX) · 23710-80F00, 23710-0A547
- OEM part numbers
- 23710-80F00, 23710-0A547
- ECU
- Nissan ECCS, S14 SR20DET
- Confidence
- low
Numbers from forum posts only (80F00 1996-98 S14 SR20DET M/T; 0A547 S14 SR20DET M/T 09/97-12/98). S14 and S14a (kouki) ECUs differ; harness covers both per year range. blank: supplier not stated by a source consulted (Nissan ECCS units are widely reported as Hitachi/JECS but not verified here)
Sources: E-1490
- Fits
- 1993-1998 S14 Silvia SR20DET, manual; JDM (and EDM 200SX variants)
- Exclusions
- automatic
- SKU
- BF29060-S3
- Maker fitment
- Nissan Silvia S14 SR20DET (Manual); selector years 1993-1996; SKU label: Manual 1993 - 1996 Nissan Silvia S14 SR20DET
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2); 1993-96

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1998 - 2002 Nissan Silvia S15 SR20DET
- Plugs into
ECCS ECU (SR20DET, S15 Silvia Spec R)
- ECU
- Nissan ECCS, S15 SR20DET
- Confidence
- low
Forum suggestions (23710-85F04 / 23710-91F**) unconfirmed; left blank. Boomslang fitment lists both S14 and S15 under this SKU: ambiguity, owner should check connector/ECU.
- Fits
- 1999-2002 S15 Silvia Spec R (6MT); Boomslang selector also lists S14 SR20DET 1997-98
- Exclusions
- automatic; Spec S (SR20DE NA)
- SKU
- BF29061-S3
- Maker fitment
- Nissan Silvia S14 SR20DET; Nissan Silvia S15 SR20DET (Manual); selector years 1997-2002; SKU label: Manual 1998 - 2002 Nissan Silvia S15 SR20DET
- Maker notes
- separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2)
Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.
Your GAINS system for this car · pre-release
ECU2 for the Silvia / 200SX S14
Planned with the same rules as the configurator for this car's 4 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.
- Price TBA
ECU2Engine controller
4 cyl · port injection · cable throttle
Full sequential fuel and spark for this 4-cylinder on a cable throttle, with the wideband built in.
in designEst. availability: April 2027
Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →
Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →
What you get
- A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
- Faults in plain words"Coolant temp sensor open circuit.
- S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
- Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
- GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.
How it wires in
- Haltech S3 plug-in harness2 listed · from $535 USD listHT-186333
- Factory-connector → S3 adapter2 listed · from $840 USD list
- Wire-inAlways possible
Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓
ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.
How GAINS approaches the Silvia / 200SX S14
Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.
- 1Base map and first startplanned
Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.
- 2Lambda targets and VE learningclosed loop on GAINS ECUs
Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.
- 3Cam phasing (VVT)gated
Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.
- 4Boost controlgated
A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.
- 5Drivability foundationsplanned
Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.
- 6Factory load sensingfactory reference
What the factory ECU measures load with: MAF (hot-wire / hot-film) (low confidence)
- 7Wideband sensorhardware
Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller
- 8Bottom end and head sealingfactory reference
Reported: MotoIQ cites rod-bearing oil starvation, finger-follower rockers flying off on over-rev, and water pump cavitation near 6,600 rpm; ring lands of stock pistons commonly reported as the first combustion-side failure (shop/forum). (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.
Drivetrain
Chassis integration
Cooling fans are ECM-controlled on the S14, so any ECU change must keep fan control. On US cars fitted with an SR20DET, the 240SX body harness expects KA24DE ECM functions, including the fan relays and A/C logic.
Tuning notes
S14 SR20DET tuning usually starts with boost via the wastegate solenoid or a boost controller, then injectors, pump, MAF upgrade or speed-density conversion, and turbo upgrades. Retune the VTC switch point when changing cams or turbo.
Popular swaps
The Silvia and 240SX share the S14 chassis, so JDM SR20DET drivetrain fits
Sourced · medium2As with the S13, the S14 SR20DET swap into a 240SX is mainly a wiring exercise: merge the SR engine harness and ECU with the US body harness or use a standalone, and recreate fan, A/C and tachometer functions.
GAINS on the Silvia / 200SX S14
ECU2
Designed so your phone is the laptop, keypad and dash
The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.
Wideband, IMU and logging built in
An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.
Modular, so you buy what the engine needs
This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.
Calibration that keeps learning
Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.
Adaptive tuning strategies
- VE learning closed loop on GAINS ECUs
Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.
- Goal-based lambda targets closed loop on GAINS ECUs
Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.
- Knock protection protection
Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.
- Warm-up, cranking, idle and transient fuel planned
The same learning approach applied to the tables tuners spend hours on after the main map is done.
- Spark advance and boost authority gated
Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.
Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.
GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.
Frequently asked
Which S14 SR20DET ECU pin is the VTC solenoid?
Terminal 113.3
Which S14 SR20DET ECU pin is the boost pressure sensor?
Terminal 35; the wastegate valve control solenoid is on terminal 25.3
What are the S14 SR20DET cam sensor pins?
Reference (180 degree) on 41 and 51, position (1 degree) on 42 and 52.3
Which 1997 240SX ECM pins are the injectors?
102 (No.1, W/B), 107 (No.2, Y/B), 104 (No.3, G/B), 109 (No.4, L/B).1
What power does the S14 SR20DET make?
Nissan rates the S14 Silvia K's Type S at 162 kW (220 PS) at 6,000 rpm and 274 Nm at 4,800 rpm.2
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- 1997 Nissan 240SX (S14, KA24DE) Service Manual, section EC · Nissan North America (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
- Nissan Heritage Collection: Silvia K's Type S (1994, S14) · Nissan Motor Co., Ltd. · oem · retrieved 2026-10-25
- Nissan Model S14 Series Service Manual (1994, LHD export, SR20DET), sections EM and EC · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
Catalog data and evidence
- Catalog data, not yet expert-reviewed.
- No vehicle photos: illustrations only until licensed imagery is available.
- E-913 Haltech S3 adapter harness page (sourced, high confidence)
- E-921 Haltech S3 adapter harness page (sourced, high confidence)
- E-934 Boomslang identity (sourced, high confidence)
- E-935 Boomslang S3 catalog size (sourced, high confidence)
- E-900 Haltech Nexus S3 catalog (sourced, high confidence)
- E-941 S3 engine harness availability (inferred, medium confidence)
- E-1490 harness ECU xref: Nissan S13/S14 SR20DET (unverified, low confidence)


