Nissan · 1999-02

Nissan Silvia S15 SR20DET ECU and tuning guide

The Nissan Silvia S15 SR20DET (1999-02) runs the SR20DET (red / black top, S15): 2 L I4, turbocharged, port injection, cable throttle.

Reviewed by GAINS editorial team on 2026-11-04.

Years1989-02
Displacement2L
LayoutI4
InductionTurbocharged
InjectionPort injection
Cam controlVTC intakeblack top +
IgnitionCoil-on-plug
Swap demandHigh

Part of the Nissan SR20 family.

Modeled power and torque

Modelled estimate, not a dyno result.

SR20DET (red / black top, S15): stock vs common buildsmodeled

Modeled estimate, not a dyno measurement. Real results vary with fuel, weather, dyno type and build.

Stock (factory-rated peaks; shape modeled)
010020030040050001002003004001k2k3k4k5k6khplb-ftrpm
Solid = power (hp), dashed = torque (lb-ft). Shaded bands show the modeled uncertainty. Hover for values.

Stock is anchored to the factory rating (247 hp at 6400 rpm, 203 lb-ft at 4800 rpm); the curve shape between peaks is modeled. Bolt-ons + tune (pump fuel, more boost): Stock turbo/supercharger; gains limited by compressor and fuel system.

SR20DET (red / black top, S15) data

Platform background

The S15 Silvia (Japan) and 200SX (Australia/New Zealand) use the final SR20DET with an ECU-controlled wastegate solenoid, an on/off intake valve timing solenoid, individual coil-on-plug ignition with built-in power transistors and high-impedance injectors. This page gives the complete Nissan S15 ECM terminal table with wire colours from the S15 EC service manual.

Factory ECU

Load strategy
  • MAF-based ECCS with closed-loop control from the front heated O2 sensor
  • Open loop under acceleration, high load and warm-up
Sourced2
Ignition

Four individual ignition signals to coils with built-in power transistors

Sourced2
Trigger

Optical camshaft position sensor: 360 slits (1 degree) and 4 slits (180 degree)

Sourced2
BoostWastegate valve control solenoid at terminal 115Sourced2
Cam timing
  • Intake valve timing control solenoid at terminal 105
  • Advance commanded from coolant temperature, engine speed and throttle position
Sourced2
DiagnosticsCONSULT-II via data link connector (terminals 7, 15, 23)Sourced2
IdleIACV-AAC valveterminal 113Sourced2

The S15 ECM is the most complete factory SR20DET controller, with sequential ignition, VTC and wastegate control on board. It has no intake air temperature input in its pin list, so charge temperature compensation is limited; standalone conversions usually add an IAT sensor.

Factory ECU: harness cross-reference

From the factory ECU each listed harness plugs into. The factory ECU is unplugged, not modified. Check the label and part number on your own ECU before ordering.

Nissan ECCS ECU, SR20DE(T) 64-pin (S15 / S14A Kouki / N15 / K11)Part numbers not yet sourced.
ECU family
Nissan 23710-series ECCS (64-pin header)
Applies to
S15 ADM/JDM; S14A Kouki; 180SX Type X 1996+; Pulsar N14/N15 SSS & GTI-R; Micra K11; manual
Not for
S13/S14 Zenki (76-pin, separate harnesses); automatic

S15 examples only (23710-91F**); 91F01 vs 91F05 interchange questioned (NATS/JDM-ADM). Harness spans many different OEM ECUs sharing one connector type; part numbers for N14/N15/K11/Kouki not gathered.

Low confidenceUnverified
ECCS ECU (SR20DET, S15 Silvia Spec R)Part numbers not yet sourced.
ECU family
Nissan ECCS, S15 SR20DET
Applies to
1999-2002 S15 Silvia Spec R (6MT); Boomslang selector also lists S14 SR20DET 1997-98
Not for
automatic; Spec S (SR20DE NA)

Forum suggestions (23710-85F04 / 23710-91F**) unconfirmed; left blank. Boomslang fitment lists both S14 and S15 under this SKU: ambiguity, owner should check connector/ECU.

Low confidenceUnverified

Factory ECU pinout

Each connector face drawn from the OEM service manual's pin data, with every terminal's function and wire colour where the manual prints it.

Nissan Silvia (S15) SR20DET ECM

The Nissan Silvia (S15) SR20DET ECM uses 1 connector with 64 cavities. This page draws each face from the OEM figure and lists the 54 terminals the OEM table documents, with wire colours where the manual prints them.

1999-2002 · Japan / Australia (S15 manual) · 1 connector, 64 cavities · 54 terminals sourced

ECM harness connector, S15 (SR20DET)64 cavities · 54 terminals listed · 64 cavities in two rows: 101-108/109-116, 1-7/8-14, centre bolt, 15-22/23-30, 31-39/40-48 (same arrangement as the S13 KA24DE figure).

Looking into the harness plug's mating face (mirror of the ECU face).

How the OEM figure is orientedHarness side (looking into the plug), as drawn in the OEM figure.
Nissan Silvia (S15) SR20DET ECM: ECM harness connector, S15 (SR20DET)101: Injector No. 1101102: no terminal listed102103: Injector No. 3103104: no terminal listed104105: Intake valve timing control solenoid valve105106: Fuel pump relay106107: ECM ground107108: ECM ground1081: Ignition signal No. 112: Tachometer23: Ignition signal No. 234: ECM relay (self shut-off)45: Ignition signal No. 356: ECM ground67: Data link connector715: Data link connector1516: Mass air flow sensor1617: Mass air flow sensor ground1718: Engine coolant temperature sensor1819: Heated oxygen sensor 1 (front)1920: Throttle position sensor2021: Sensors' ground2122: no terminal listed2231: Camshaft position sensor (reference signal)3132: Vehicle speed sensor3233: Electrical load signal (headlamp and rear defogger) (M/T)3334: Start signal3435: PNP switch (M/T)3536: Ignition switch3637: Sensors' power supply (5 V)3738: Power supply for ECM3839: ECM ground39109: Current return (grouped with back-up supply in the main table)109110: Injector No. 2110111: Heated oxygen sensor 1 heater (front)111112: Injector No. 4112113: IACV-AAC valve113114: no terminal listed114115: Wastegate valve control solenoid valve115116: ECM ground1168: no terminal listed89: Cooling fan relay (low)910: Cooling fan relay (high)1011: Air conditioner relay1112: A/T signal No. 31213: ECM ground1314: no terminal listed1423: Data link connector2324: Malfunction indicator lamp2425: Ignition signal No. 42526: no terminal listed2627: Knock sensor2728: Throttle position sensor signal output (to A/T)2829: no terminal listed2930: Camshaft position sensor (position signal)3040: no terminal listed4041: Air conditioner switch4142: no terminal listed4243: Power steering oil pressure switch4344: A/T signal No. 24445: A/T signal No. 14546: Power supply for ECM (back-up)4647: Power supply for ECM4748: ECM ground48
Hover, tap or tab to a cavity to see its terminal.
PinFunctionTypeWireNotes
1Ignition signal No. 1IgnitionR/W
2TachometerComms / diagL/OR
3Ignition signal No. 2IgnitionBR/R
4ECM relay (self shut-off)OutputsR/B
5Ignition signal No. 3IgnitionR/G
6ECM groundGroundB
7Data link connectorComms / diagBR/Y
9Cooling fan relay (low)OutputsP/B
10Cooling fan relay (high)OutputsL/G
11Air conditioner relayOutputsG
12A/T signal No. 3Sensor signalPU/W
13ECM groundGroundB
15Data link connectorComms / diagSB
16Mass air flow sensorSensor signalL
17Mass air flow sensor groundSensor 5 V / groundP
18Engine coolant temperature sensorSensor signalP/B
19Heated oxygen sensor 1 (front)Sensor signalW
20Throttle position sensorSensor signalR
21Sensors' groundSensor 5 V / groundGY
23Data link connectorComms / diagG/R
24Malfunction indicator lampComms / diagOR
25Ignition signal No. 4IgnitionR/L
27Knock sensorSensor signalW
28Throttle position sensor signal output (to A/T)Sensor signalR/Y
30Camshaft position sensor (position signal)Crank / camB/Y
31Camshaft position sensor (reference signal)Crank / camLG
32Vehicle speed sensorSensor signalW/PU
33Electrical load signal (headlamp and rear defogger) (M/T)Sensor signalG/RA/T: Electrical load signal (headlamp and rear defogger) (wire PU).
34Start signalSensor signalOR/L
35PNP switch (M/T)Sensor signalG/ORA/T: PNP switch (wire R/G).
36Ignition switchPowerB/R
37Sensors' power supply (5 V)Sensor 5 V / groundLG/R
38Power supply for ECMPowerB/W
39ECM groundGroundB
41Air conditioner switchSensor signalL/B
43Power steering oil pressure switchSensor signalPU/W
44A/T signal No. 2Sensor signalL/W
45A/T signal No. 1Sensor signalL/OR
46Power supply for ECM (back-up)PowerW
47Power supply for ECMPowerB/W
48ECM groundGroundB
101Injector No. 1InjectorW/G
103Injector No. 3InjectorG/B
105Intake valve timing control solenoid valveOutputsR/L
106Fuel pump relayOutputsB/P
107ECM groundGroundB
108ECM groundGroundB
109Current return (grouped with back-up supply in the main table)PowerW
110Injector No. 2InjectorL/R
111Heated oxygen sensor 1 heater (front)OutputsB/R
112Injector No. 4InjectorL/B
113IACV-AAC valveOutputsSB
115Wastegate valve control solenoid valveOutputsOR/B
116ECM groundGroundB

Our drawing from published pin data; not an OEM drawing. Layout from the OEM face view (high confidence). Confirm against the factory manual for your exact year and market before cutting or pinning wires.

Coverage, year splits and safety

Covers the S15 SR20DET ECM from Nissan's Model S15 Series service manual. A/T-only uses of a cavity are noted on the pin.

Source notes: From the Nissan Model S15 Series Service Manual, section EC, 'ECM Terminals and Reference Value' inspection table (EC-76 to EC-81) and the power supply circuit table. Wire colours are terminal-side harness colours. The market of this manual edition (CONSULT-II, Australian/NZ 200SX or Japanese Silvia) is not stated on the parsed pages; confirm against the vehicle.

Safety: disconnect the battery before working on the ECU harness, and confirm each terminal with a meter against your own car's manual before cutting or pinning wires.

All factory ECU pinouts →

Plug-and-play harness

Route for this carS3 plug-in harness
1 · S3 plug-in2 · Factory-connector adapter3 · Wire-in

A plug-in harness built for the Haltech Nexus S3 pinout is listed for this vehicle. The ECU2 follows that published pinout, so the factory ECU is unplugged and the ECU2 plugs into the car's own loom. Nothing is written to the factory ECU. Pin-compatible per the published S3 pinout, not yet fit-tested.

MakerHarnessFitsLink
Nexus S2/S3 Plug n Play Adapter Harness Nissan Silvia S15HT-186341S15 ADM/JDM; S14A Kouki; 180SX Type X 1996+; Pulsar N14/N15 SSS & GTI-R; Micra K11; manual$535LowestMaker ↗
Manual 1998 - 2002 Nissan Silvia S15 SR20DETBF29061-S31999-2002 S15 Silvia Spec R (6MT); Boomslang selector also lists S14 SR20DET 1997-98$840Maker ↗
Wire-inUniversal flying lead or re-terminated factory harnessAny engine (terminate to ECU2's two Superseal 34 connectors)Universal harness from $405Maker ↗

Nexus S2/S3 Plug n Play Adapter Harness Nissan Silvia S15

$535USD list · excl. tax
Plug-and-playManual onlyOff-road / competition onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
Nissan ECCS ECU, SR20DE(T) 64-pin (S15 / S14A Kouki / N15 / K11) · 23710-91F01, 23710-91F05
OEM part numbers
23710-91F01, 23710-91F05
ECU
Nissan 23710-series ECCS (64-pin header)
Confidence
low

S15 examples only (23710-91F**); 91F01 vs 91F05 interchange questioned (NATS/JDM-ADM). Harness spans many different OEM ECUs sharing one connector type; part numbers for N14/N15/K11/Kouki not gathered.

Fits
S15 ADM/JDM; S14A Kouki; 180SX Type X 1996+; Pulsar N14/N15 SSS & GTI-R; Micra K11; manual
Exclusions
S13/S14 Zenki (76-pin, separate harnesses); automatic
SKU
HT-186341
Maker fitment
Nissan 200SX/Silvia S15 (ADM, JDM), S14A Kouki, 180SX Type X 1996+, Pulsar N15/N14 SSS and GTI-R, Micra K11; manual only

Boomslang plug-and-play harness for Haltech Nexus S3 - Manual 1998 - 2002 Nissan Silvia S15 SR20DET

$840USD list
Plug-and-playManual onlyhigh confidenceS3 fit not yet tested ⓘ
Plugs into
ECCS ECU (SR20DET, S15 Silvia Spec R)
ECU
Nissan ECCS, S15 SR20DET
Confidence
low

Forum suggestions (23710-85F04 / 23710-91F**) unconfirmed; left blank. Boomslang fitment lists both S14 and S15 under this SKU: ambiguity, owner should check connector/ECU.

Fits
1999-2002 S15 Silvia Spec R (6MT); Boomslang selector also lists S14 SR20DET 1997-98
Exclusions
automatic; Spec S (SR20DE NA)
SKU
BF29061-S3
Maker fitment
Nissan Silvia S14 SR20DET; Nissan Silvia S15 SR20DET (Manual); selector years 1997-2002; SKU label: Manual 1998 - 2002 Nissan Silvia S15 SR20DET
Maker notes
separate SKUs exist for other Nexus models (-S2/-R3/-R5/-T1/-T2)

Haltech and Boomslang are trademarks of their respective owners. GAINS is not affiliated with or endorsed by them.

Your GAINS system for this car · pre-release

ECU2 for the Silvia S15

Planned with the same rules as the configurator for this car's 4 cyl · port injection · cable throttle. The factory ECU is unplugged and replaced; nothing is written to it.

  • ECU2Engine controller

    4 cyl · port injection · cable throttle

    Full sequential fuel and spark for this 4-cylinder on a cable throttle, with the wideband built in.

    in designEst. availability: April 2027

    Price TBA

Add PDM2 to switch and protect chassis loads (pumps, fans, lights, accessories). Add it in the configurator →

Track days? Add the Telemetry Dongle Pro for 25 Hz GPS lap timing; it plugs into the OBD-II port, and your phone is the dash. Plan it in the configurator →

What you get

  • A screen on the ECUA 2.4-inch, 500-nit display in the lid, readable in a footwell.
  • Faults in plain words"Coolant temp sensor open circuit.
  • S3-style harnessesConnector A and C pin functions follow the published Nexus S3 wiring diagram.
  • Powered CAN portA sealed 4-pin port on the insert carries 12 V and CAN for the PDM2 and GAINS displays: one cable per accessory.
  • GAINS insideThe on-ECU adaptive layer, the app, logging and your limits.

How it wires in

  1. Haltech S3 plug-in harness1 listed · from $535 USD listHT-186341
  2. Factory-connector → S3 adapter1 listed · from $840 USD list
  3. Wire-inAlways possible

Pin-compatible per the published S3 pinout, not yet fit-tested. Every harness option for this car ↓

ECU2 is in design; specifications may change. All GAINS hardware is pre-release concept design; nothing is for sale yet and no application is validated on a vehicle. Harness fitment is from published pinouts and not yet fit-tested.

How GAINS approaches the Silvia S15

Our starting method for this engine, as foundations first: get it running and drivable, then learn fuel, then the hardware-specific strategies. It is a methodology outline, not a validated calibration.

  1. 1
    Base map and first startplanned

    Start from displacement, injector data and the sensors fitted, then let the first-start learner settle cranking, idle and warm-up before any load work. The goal is a safe, running engine, not a finished calibration.

  2. 2
    Lambda targets and VE learningclosed loop on GAINS ECUs

    Air-fuel targets come from your goal (street, track, economy). The ECU then learns its fuel table cell by cell from the onboard wideband inside a signed envelope, and you approve promoting what it learned into the base map.

  3. 3
    Cam phasing (VVT)gated

    Begin with conservative overlap. Cam targets per load cell are then chosen with torque and knock in mind, keeping idle and cold overlap low for stability. Widening cam authority follows the same evidence-gated path as spark.

  4. 4
    Boost controlgated

    A closed-loop boost target by gear and goal, held inside the authority envelope, with knock protection active at boost. Raising boost authority is never automatic; it stays an expert or dyno decision.

  5. 5
    Drivability foundationsplanned

    Pedal map, tip-in and decel fuel, idle control, cold start and warm-up enrichment: the tables tuners spend hours on after the main map. Each is a strategy in the knowledge engine with its own limits.

  6. 6
    Factory load sensingfactory reference

    What the factory ECU measures load with: MAF (hot-wire / hot-film) (low confidence)

  7. 7
    Wideband sensorhardware

    Add a wideband: the factory narrowband only tells rich from lean around stoichiometric, so it cannot close the loop at power or economy targets; fit a Bosch LSU 4.9 for the GAINS ECU's built-in controller

  8. 8
    Bottom end and head sealingfactory reference

    Reported: MotoIQ cites rod-bearing oil starvation, finger-follower rockers flying off on over-rev, and water pump cavitation near 6,600 rpm; ring lands of stock pistons commonly reported as the first combustion-side failure (shop/forum). (medium confidence) Limits depend on tune quality, fuel, rpm and condition and are not guaranteed.

Drivetrain

Transmissions

Manual and automatic versions (ECM has PNP switch, A/T signal and A/T TPS output lines)

Sourced · medium2

Chassis integration

Cooling fans

ECM controls low and high cooling fan relays (terminals 9 and 10)

Sourced2
A/CA/C switch (41) in, A/C relay (11) outSourced2
TachometerTachometer drive from terminal 2Sourced2
Vehicle speedVehicle speed sensor input at terminal 32Sourced2
Power steeringPower steering oil pressure switch at terminal 43Sourced2

A replacement ECU must drive the cooling fan relays, tachometer and A/C relay that the S15 ECM controls, and provide the MIL drive if a warning lamp function is wanted.

Tuning notes

InjectorsApprox. 11 ohmhigh impedanceSourced2
Fuel pressure

About 245 kPa at idle with vacuum, 294 kPa with regulator vacuum disconnected

Sourced2
MAF output0.8-1.5V at idleSourced2

Common S15 upgrades are boost via the factory wastegate solenoid or an aftermarket controller, intercooler, larger injectors and pump, MAF upgrade or MAP conversion, then a larger turbo. Keep a close eye on the single knock sensor's coverage and use wideband lambda for all full-load work.

Popular swaps

Engine family
  • S15 SR20DET is the last SR20DET variant
  • It shares 86 x 86 mm dimensions with earlier SR20s
Sourced · medium13

S15 SR20DETs are popular swap engines for S13 and S14 chassis because they bring VTC, wastegate control and coil-per-cylinder ignition in one package. When swapping, use the S15 ECM table above to map each function to the host chassis harness.

GAINS on the Silvia S15

ECU2

ECU2Full sequential fuel and spark for this 4-cylinder on a cable throttle, with the wideband built in.Est. availability: April 2027
Hardware fromPrice TBAPlan and compare costs

Designed so your phone is the laptop, keypad and dash

The GAINS app is designed to handle tuning, logging, gauges and switch inputs over Bluetooth, so the system needs no separate CAN keypad or display. Keypad, dash and logging views are planned; the iOS prototype runs on simulated data today.

Wideband, IMU and logging built in

An onboard Bosch LSU 4.9 wideband controller, a 6-axis IMU and onboard logging are designed into the ECU rather than sold as add-on modules.

Modular, so you buy what the engine needs

This engine runs on ECU2. PDM2 (power, body and gearbox) is optional and connects over ECU2's powered CAN port; the Telemetry Dongle Pro adds GPS lap timing from the OBD-II port.

Calibration that keeps learning

Instead of a fixed map that drifts as parts and conditions change, the ECU keeps adapting its fuel trims within limits you can see and approve in the app.

Adaptive tuning strategies

  • VE learning closed loop on GAINS ECUs

    Learns the fuel table from the onboard wideband as you drive, cell by cell, inside a signed authority envelope. Learned trims are promoted into the base map without a step in fuelling.

  • Goal-based lambda targets closed loop on GAINS ECUs

    Sets air-fuel targets from your goal (economy, response, power, safety margin) instead of a single fixed table.

  • Knock protection protection

    Listens for knock on a dedicated knock processor, pulls timing at once and restores it slowly. It only ever reduces advance.

  • Warm-up, cranking, idle and transient fuel planned

    The same learning approach applied to the tables tuners spend hours on after the main map is done.

  • Spark advance and boost authority gated

    Widening ignition advance or boost is never automatic. It stays an expert or dyno decision until validated knock detection exists for the engine family.

Already running another ECU? In advisor mode the same strategies read your logs and recommend exact table changes with the reasoning, which you apply in your ECU vendor's own software.

GAINS hardware is pre-release concept design. Simulated results only; nothing is validated on a vehicle yet.

Frequently asked

Which S15 ECU pins are the ignition signals?

Terminals 1 (No.1, R/W), 3 (No.2, BR/R), 5 (No.3, R/G) and 25 (No.4, R/L).2

Which S15 ECU pins are the injectors?

101 (No.1, W/G), 110 (No.2, L/R), 103 (No.3, G/B), 112 (No.4, L/B).2

Which S15 ECU pin is the wastegate solenoid?

Terminal 115 (OR/B), wastegate valve control solenoid valve.2

What are the S15 cam sensor pins?

Position (1 degree) on terminal 30 (B/Y) and reference (180 degree) on terminal 31 (LG).2

Are S15 injectors high impedance?

Yes, about 11 ohm per Nissan's SDS.2

Which pin drives the S15 VTC solenoid?

Terminal 105 (R/L), intake valve timing control solenoid valve.2

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Nissan Model S14 Series Service Manual (1994, LHD export, SR20DET), sections EM and EC · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
  2. Nissan Model S15 Series Service Manual, section EC (Engine Control System, SR20DET) · Nissan Motor Co., Ltd. (archived copy from nicoclub.com) · service-manual · retrieved 2026-10-25
  3. Nissan SR engine · Wikipedia · community · retrieved 2026-10-25

Catalog data and evidence

  • Catalog data, not yet expert-reviewed.
  • No vehicle photos: illustrations only until licensed imagery is available.
  1. E-921 Haltech S3 adapter harness page (sourced, high confidence)
  2. E-934 Boomslang identity (sourced, high confidence)
  3. E-935 Boomslang S3 catalog size (sourced, high confidence)
  4. E-900 Haltech Nexus S3 catalog (sourced, high confidence)
  5. E-941 S3 engine harness availability (inferred, medium confidence)