United Kingdom · 1961-1967 · Smiths, Lucas instruments

Triumph TR4 and TR4A gauges

5 in glass on the big dialsMechanical cable tachPositive-earth 10 V stabiliserDomed glass early, flat glass laterElectric temperature senderMechanical oil pressure pipe

Triumph TR4 gauges are Smiths instruments with a Lucas ammeter: a cable speedometer and a cable-driven tachometer behind 5 in glasses, plus small fuel, water temperature and oil pressure gauges. Early TR4s have domed glasses; later TR4s and the TR4A have flat ones. The thermal fuel and temperature gauges run from a positive-earth 10 V stabiliser.Medium12

6 gauges · 115 mm + 52 mm

A Round Gauge kit for the Triumph TR4 and TR4A

Built from the factory gauge sizes below: one digital gauge per hole.

Factory gauges

6 round instruments in the factory dash

InstrumentOriginal sizeHow it worksRound Gauge
SpeedometerSmiths SN6313 (TR4), SN6325 (TR4A)Large dial with a 5 in (127 mm) glass; hole size not publishedMedium1Cable drive115 mm With a ringThe 5 in glass is larger than any Round Gauge size, so the largest one would need a ring. Measure the opening first.
TachometerSmiths RN1409/02 (TR4), RN1417/00 (TR4A)Large dial with a 5 in (127 mm) glass; hole size not publishedMedium1Cable-driven tach115 mm With a ringCable-driven: 48 in cable on RHD, 36 in on LHD.
Water temperatureSmiths BT2300 (early TR4), BT2203 (later TR4, TR4A)Small gauge; size not publishedLow2Thermal (bimetal)52 mm To measure
Oil pressureSmiths PL2561 (early TR4), PL2302/22 (later TR4, TR4A)Small gauge; size not publishedLow2Pressure line (mechanical)52 mm To measure
Fuel gaugeSmiths BF2301/00 (early TR4), BF2206/00 (later TR4, TR4A)Small gauge; size not publishedLow2Thermal (bimetal)52 mm To measure
AmmeterLucas 36264A/DSmall gauge on its own bracket; size not publishedLow2Moving iron / air-core52 mm To measure

Electrical facts for a gauge swap

Earth polarity, stabiliser, senders and signal types.

Earth polarityPositive earthRimmer lists the positive-earth stabiliser for the TR4 and TR4A small instruments.Sourced · medium2
Voltage stabiliser
  • Smiths 10 V stabiliser, positive earth (BR1308)
  • Feeds up to three gauges
Sourced · medium2
Temperature sender
  • Electrical transmitter in the thermostat housing (GTR104)
  • TR2-TR3A use a capillary gauge
Sourced · medium2
Fuel sender rangeNot published in the TR4 sources we usedMeasure the sender empty and full before choosing a digital gauge.Researched, unverified2
Tach drive
  • Mechanical cable
  • No electrical tach signal at the dash
Sourced · medium1
Speedometer drive
  • Cable
  • Heads matched to 3.7:1 or 4.1:1 axles and 6.95x15 or 165x15 tires
  • TR4A uses an angle drive at the gearbox
Sourced · medium1

The factory dash and its variants

The TR4 dash carries two large dials with 5 in glasses and a row of small Smiths gauges for fuel, water temperature and oil pressure, plus a Lucas ammeter.Medium12

Rimmer splits the instruments at commission CT15053 (RHD) and CT11307 (LHD). Earlier TR4s have domed glasses and a metal fascia; later TR4s and the TR4A have flat glasses and a veneered fascia.Medium21

The gauge list here applies to both, with part references for each. Check the commission number on your car before ordering.Medium2

How the original instruments work

The tachometer is mechanical, turned by a cable from the engine.

The speedometer is cable-driven, and each head is calibrated for an axle ratio and tire size.Medium1

Fuel and temperature gauges are thermal types fed at 10 V by a Smiths stabiliser. The stabiliser takes 12 V on terminal B and feeds the gauges from terminal I.Medium23

The TR4 moved to an electrical temperature transmitter in the thermostat housing. The earlier TR2 to TR3A cars use a capillary gauge instead.Medium2

Oil pressure reaches the gauge through a pipe: rigid with a flexible hose on early TR4s, nylon on later TR4s and the TR4A.Medium2

What owners replace and why

Several original gauges are now listed as no longer available, even as reconditioned exchange units.

That leaves owners rebuilding their own or fitting replacements.Medium21

Owners converting to negative earth must change the stabiliser too. The positive-earth unit cannot be used on a negative-earth car, and the negative-earth version is a different part.Medium2

Going digital without losing the look

The big dials are the hard part.

A 5 in glass is larger than a 115 mm (4.5 in) gauge, so a ring or cup is likely needed to fill the opening.Medium1

Positive earth is the second trap. Many modern electronic gauges are built for negative earth only, so convert the car or check the gauge's polarity rating first.Medium24

The tach is mechanical, so a digital tach needs a new signal wire from the coil. GPS speed removes axle-ratio matching. Keep the originals and cables in place for a reversible fit.Low14

Common faults with the original gauges

  1. 1Fuel and temperature gauges dead after a negative-earth conversion

    Usual cause

    The positive-earth stabiliser left in place

    Fix

    Fit the negative-earth stabiliser (BHA4602P) when converting polarity.Medium2

  2. 2Speedometer reads wrong

    Usual cause

    Head calibrated for a different axle ratio or tire size

    Fix

    Fit the SN6313 or SN6325 head for your axle (3.7:1 or 4.1:1) and tire size, or have it recalibrated.Medium1

  3. 3Oil pressure gauge leaks or reads erratically

    Usual cause

    Worn pipe, hose or leather sealing washer at the gauge

    Fix

    Replace the pipe or hose and the sealing washer; check the routing through the bulkhead grommet.Low2

Restoration tips

Keep it original and reversible

  • Keep domed-glass and flat-glass instruments together; mixing them on one dash is a giveaway.Medium21
  • Note the SN number on the speedometer; it ties the head to an axle ratio and tire size.Medium1
  • LED gauge bulbs sold for this car are negative-earth only; keep filament bulbs on a positive-earth car.Medium2

Frequently asked

Is the TR4 tachometer mechanical?

Yes. Both the TR4 (Smiths RN1409/02) and TR4A (RN1417/00) tachs are driven by a cable from the engine, 48 in long on right-hand-drive cars and 36 in on left-hand drive. An electronic tach needs a new signal wire from the ignition coil.Medium1

Is the TR4 positive earth?

Yes. Rimmer lists a positive-earth Smiths voltage stabiliser for the TR4 and TR4A small instruments, and notes it only works on positive-earth systems. Cars converted to negative earth need the negative-earth stabiliser, and any electronic gauge must suit the polarity.Medium2

How big are TR4 speedometer and tachometer?

Rimmer lists the large gauge glass as 5 in (127 mm) for both domed and flat versions. No supplier we checked publishes the dash opening, so measure it. A 5 in dial is larger than common 100 mm replacements, so most need a ring to fill the hole.Medium1

What is the difference between TR4 and TR4A gauges?

Early TR4s to commission CT15053 (RHD) and CT11307 (LHD) use domed glasses and different gauge references. Later TR4s and the TR4A use flat glasses, SN6325 speedometers and the RN1417 tach. The TR4A also uses a speedometer angle drive at the gearbox.Medium12

Related cars

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Triumph TR4-4A speedometer and tachometer · Rimmer Bros · vendor-doc · retrieved 2026-11-03
  2. Triumph TR4-4A small instruments · Rimmer Bros · vendor-doc · retrieved 2026-11-03
  3. MGB voltage stabilizer tech tip · Chicagoland MG Club · community · retrieved 2026-11-03
  4. Instructions for 80mm/100mm 12 volt Smiths Classic tachometer · Smiths Instruments (Caerbont) · vendor-doc · retrieved 2026-11-03

Markets: UK, USA, Canada, Australia, Europe. Make and model names identify the vehicle only; GAINS is not affiliated with the vehicle or instrument makers.