United Kingdom · 1962-1980 · Smiths, Jaeger instruments

MG MGB and MGB GT gauges

Smiths instruments80 mm or 100 mm big dials: measure first52 mm small gaugesMechanical oil pressure line10 V stabilizer from 1965 model yearPositive earth on early cars

MGB gauges are Smiths instruments: a cable-driven speedometer and an electric tachometer, plus 52 mm (2 in) fuel and dual oil-pressure and water-temperature gauges. Big-dial size is the trap. Owners report both 80 mm (3 1/8 in) and 100 mm (4 in) speedo and tach bodies depending on dash generation, so measure the hole before ordering anything.Medium125

4 gauges · 100 mm + 52 mm

A Round Gauge kit for the MG MGB and MGB GT

Built from the factory gauge sizes below: one digital gauge per hole.

Factory gauges

4 round instruments in the factory dash

InstrumentOriginal sizeHow it worksRound Gauge
Speedometer80 mm (3 1/8 in) or 100 mm (4 in) body, varies by dash generationLow123Cable drive100 mm To measureOwner reports conflict: one quotes a 3 1/8 in (79 mm) hole, a 1967 GT owner measured about 3 7/8 in (98 mm), and a 1978 owner measured 4 in (102 mm). Measure your own hole; 80 mm is the other candidate.
Tachometer80 mm (3 1/8 in) or 100 mm (4 in) body, matches the speedometerLow21112Current impulse100 mm To measureSame size question as the speedometer. Early positive-earth cars use a Smiths electric tach with a pickup loop in the coil feed; later cars use a voltage-triggered unit.
Oil pressure and water temperature (dual)Smiths or Jaeger dual gauge, MGB to 196752 mm (2.05 in) body, 56 mm (2.20 in) bezelMedium56Capillary (mechanical)52 mm Size matchOil side is a mechanical pressure line and the temperature side a capillary bulb, so the two halves come out as one sealed unit.
Fuel gaugeSmall Smiths case, same pod size as the dual gaugeLow107Thermal (bimetal)52 mm To measureNo supplier page we found states the fuel gauge diameter; it shares the small-gauge layout with the dual gauge. Measure before ordering.

Electrical facts for a gauge swap

Earth polarity, stabiliser, senders and signal types.

Earth polarity
  • Positive earth on early cars
  • Negative earth on later cars
The 1965-1967 electric tach is a positive-earth unit, and a rarer internal variant appeared in late 1967 production. Confirm your car's polarity at the battery before wiring anything.Researched, unverified114
Voltage stabilizer
  • Average about 10 V, switched on and off roughly once a second
  • From the 1965 model year
Chicagoland MG Club gives the 1965 model year; Rimmer Bros describes it as standard on the MGB from 1964. It feeds the fuel gauge and, on some cars, the temperature gauge.Conflict109
Fuel sender rangeAbout 220 ohms empty to 20 ohms fullClub figure, which also says the value varies by application. Mini owners quote about 240 ohms empty and 33 ohms full for the same Smiths family. Measure the sender you have.Researched, unverified1013
Tach trigger
  • Current-impulse pickup on early positive-earth cars
  • Voltage-triggered on later cars
Identify by the back of the case: the impulse type has a wire loop that runs through it in the coil feed.Researched, unverified1112
Speedometer drive
  • Cable from the gearbox
  • Turns-per-mile varies with axle ratio and overdrive
Read the number on the speedometer face before ordering a replacement or calibrating a digital unit.Researched, unverified3

The factory dash and its variants

Every MGB carries a large speedometer and tachometer in front of the driver, with small gauges for fuel and a dual oil-pressure and water-temperature unit. The early cars have a painted steel dash; North American cars got a padded dash from the late 1960s, and the 1977-on cars have a revised console.Low23

The gauge list here describes the steel-dash cars to 1967, which carry the dual gauge that suppliers list as MGB to 1967. Later dashes change the small-gauge mix, so check a later car against its own parts list.Medium56

Big-dial size is disputed among owners. One summary gives 100 mm bodies for steel-dash cars, 80 mm for the early padded dashes and 100 mm again for rubber-bumper cars. Another owner says every tach and speedo to the 1977 model year is 80 mm.Low32

How the original instruments work

The fuel gauge is a thermal type.

A small heater warms a bimetal strip that bends to move the needle, so it reacts slowly and ignores fuel slosh.Medium10

The stabilizer that feeds it does not hold a steady 10 V. It switches between full battery voltage and zero about once a second, and the average works out near 10 V.Medium10

The oil gauge reads pressure through a pipe from the engine, and the temperature gauge uses a sealed capillary to a bulb in the head. Moss lists the dual unit with an 82 in (2.08 m) capillary.Medium65

The early electric tach senses current pulses in the coil feed through a pickup in the case. Converting one to negative earth means reversing the external wires and swapping power and earth inside the case.Medium11

What owners replace and why

The usual complaints are a fuel gauge that reads low or dead, a temperature gauge whose capillary has been kinked, and a tach that stopped working after a polarity change.Medium1011

Owners fitting aftermarket dials report that the quoted case diameter often includes clearance. One installer still had to open the hole by about 2 mm all round, and others use a rotary tool to enlarge it.Low2

Going digital without losing the look

A digital set has to answer four questions on an MGB: earth polarity, the speed source, the tach signal and the senders.

GPS speed avoids matching the cable's turns-per-mile; a cable sender or hall pickup keeps the drive.Low311

Most electronic tachs want a voltage signal from the coil negative. That is a different signal from the current pickup the early impulse tach uses, so wire it from the coil terminal, not the loop.Medium1211

Keeping the factory fuel sender means the new gauge must read its roughly 20-240 ohm range. A digital gauge fed from the 10 V stabilizer will see a switching supply, so feed it from a fused ignition source instead.Low1013

The mechanical oil and capillary temperature lines need new electrical senders if those gauges go digital. Keep the original dual gauge boxed so the car can return to stock.Medium6

Common faults with the original gauges

  1. 1Fuel gauge reads low or not at all

    Usual cause

    Poor stabilizer earth through its mounting, loose terminals, or a poor tank-to-body earth

    Fix

    Tighten the stabilizer screws, check its mounting orientation, and confirm near-zero ohms from tank to body. Shorting the gauge signal terminal to earth should drive it to F.Medium10

  2. 2Fuel gauge rises with engine speed

    Usual cause

    A failing stabilizer passing charging-system voltage through to the gauge

    Fix

    Replace the stabilizer with the correct-polarity unit; solid-state replacements exist for both polarities.Low98

  3. 3Tach dead after converting the car to negative earth

    Usual cause

    The positive-earth electric tach has polarity-specific internal wiring

    Fix

    Reverse the wires at the back and swap power and earth inside the case, following the procedure for your unit; late-1967 units differ.Medium11

Restoration tips

Keep it original and reversible

  • Measure the speedo and tach holes before ordering; MGB owners report 80 mm and 100 mm bodies.Low12
  • Keep the original stabilizer polarity matched to the car; positive-earth and negative-earth units are different parts.Medium98
  • Record the turns-per-mile number on the speedometer face before removing it.Low3
  • Store the dual gauge with its capillary coiled loosely; a kinked capillary cannot be repaired by bending it straight.Low6

Frequently asked

What size are MGB speedometer and tachometer gauges?

They are either about 80 mm (3 1/8 in) or 100 mm (4 in), and owners disagree on which years used which. Reported hole measurements range from 3 1/8 in on some cars to 4 in on a 1978 car. Measure the hole in your own dash, edge to edge through the center, before you order a replacement.Low123

Does the MGB have a voltage stabilizer?

Yes, from about the 1965 model year. It feeds the fuel gauge and, on some cars, the temperature gauge, by switching battery voltage on and off so the average is about 10 V. Rimmer Bros dates its fitment to 1964, so sources differ by a year. Earlier cars run the gauges differently.Medium109

Is the MGB oil pressure gauge mechanical?

Yes. On the early cars it shares a 52 mm (2.05 in) case with the water temperature gauge. Oil pressure reaches it through a pipe from the engine, and temperature through a sealed capillary to a bulb in the head. The unit is replaced as a whole, and Moss lists it with an 82 in capillary.Medium56

Why does my MGB fuel gauge read wrong?

Most often the earth is at fault. The stabilizer earths through its mounting screws, and the tank must earth to the body. Check both, then short the gauge signal wire to earth: the needle should go to F. If it does, look at the sender and wiring; if not, look at the gauge or stabilizer.Medium10

Can I convert an MGB tach to negative earth?

Yes, the 1965-1967 Smiths electric tach can be converted. You reverse the wires at the back of the unit and swap the power and earth connections inside the case. A less common late-1967 version has different internal parts and needs another procedure, so open it and check before you start.Medium11

Related cars

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

13 sources
  1. Size of hole in dash for speedo/tach - 80B · The MG Experience forum · community · retrieved 2026-11-03
  2. Speedometer and tachometer sizing for replacement units · The MG Experience forum · community · retrieved 2026-11-03
  3. Smiths speedometers for MGs (with or without overdrive) - overview · The MG Experience forum · community · retrieved 2026-11-03
  4. Negative earth conversion · The MG Experience · community · retrieved 2026-11-03
  5. Gauge, dual oil pressure / water temp, MGA, MGB to 67 · British Parts Northwest · vendor-doc · retrieved 2026-11-03
  6. Oil/water gauge, Smiths replacement (361-761) · Moss Motors · vendor-doc · retrieved 2026-11-03
  7. Gauge, fuel (361-860) · Moss Motors · vendor-doc · retrieved 2026-11-03
  8. Solid state voltage stabilizer, positive ground · Moss Motors · vendor-doc · retrieved 2026-11-03
  9. MGB voltage stabiliser · Rimmer Bros · vendor-doc · retrieved 2026-11-03
  10. MGB voltage stabilizer tech tip · Chicagoland MG Club · community · retrieved 2026-11-03
  11. Converting the electric tach to negative earth · The MGA With An Attitude (Barney Gaylord) · community · retrieved 2026-11-03
  12. Instructions for 80mm/100mm 12 volt Smiths Classic tachometer · Smiths Instruments (Caerbont) · vendor-doc · retrieved 2026-11-03
  13. Checking, testing and adjusting Smiths fuel gauges · The Mini Forum · community · retrieved 2026-11-03

Markets: UK, USA, Canada, Australia, Europe, South Africa. Make and model names identify the vehicle only; GAINS is not affiliated with the vehicle or instrument makers.