A Round Gauge kit for the Triumph TR6 (and TR250)
Built from the factory gauge sizes below: one digital gauge per hole.
Factory gauges
6 round instruments in the factory dash
| Instrument | Original size | How it works | Round Gauge |
|---|---|---|---|
| SpeedometerSmiths SN6411 series | Large main dial; diameter not published by the suppliers we checkedLow5 | Cable drive | 100 mm To measureMeasure the opening before ordering. |
| TachometerSmiths RN2413/00A (CP/CC), RN2414/00A (CR/CF) | Large main dial; diameter not published by the suppliers we checkedMedium34 | Cable-driven tach | 100 mm To measureCable-driven; RHD cables are 42 in or 48 in, LHD 33 in or 36 in. |
| Water temperatureSmiths BT2230/00 (CR/CF); BT2215/00 (CP/CC) | 52 mm (2 in)Medium21 | Thermal (bimetal) | 52 mm Size match |
| Fuel gaugeSmiths BF2232/00 (CR/CF); BF2221/00 (CP/CC) | 52 mm (2 in)Medium26 | Thermal (bimetal) | 52 mm Size matchRimmer lists BF2232/00 as 52 mm on its Midget 1500 page; the same part number appears on the TR6 CR/CF list. |
| Oil pressureSmiths PL2302/33 (CP/CC), PL2319/00 (CR/CF) | Small gauge, same row as the temperature and fuel gaugesLow217 | Pressure line (mechanical) | 52 mm To measureSize not stated by Rimmer; it sits in the 52 mm small-gauge row. |
| Ammeter (CP/CC) or voltmeter (CR/CF)Lucas 36427 ammeter; Smiths BV2213/00 voltmeter | Small gauge, same row as the othersLow12 | Moving iron / air-core | 52 mm To measure |
Electrical facts for a gauge swap
Earth polarity, stabiliser, senders and signal types.
- Yes
- Feeds the thermal fuel and temperature gauges at about 10 V average
Electrical transmitter in the head (Rimmer lists GTR108 as an aftermarket replacement)
Sourced · medium2- Cable
- SN6411 heads matched to 3.45:1 (PI) or 3.7:1 (carburetor) axles
The factory dash and its variants
The TR6 wood dash carries a speedometer and tachometer in front of the driver and a row of 52 mm small gauges: fuel, water temperature, oil pressure and an ammeter or voltmeter.Medium12
Rimmer splits the instruments by commission series. Early CP (PI) and CC (US carburetor) cars use an ammeter; the later CR and CF series use a voltmeter and revised gauge references.Medium12
Moss sells separate gauge sets for the TR250 and TR6 through 1972 and for the 1973-1976 TR6. The gauge list here follows the CR/CF layout with the voltmeter.Medium72
How the original instruments work
The tachometer is mechanical.
A cable from the engine turns it, so no electrical tach signal exists behind the dash.Medium34
Fuel and temperature gauges are thermal types on a voltage stabilizer. The stabilizer pulses battery voltage to give about 10 V average, and the slow bimetal movement smooths it.Medium87
The speedometer is cable-driven and calibrated to the axle. Rimmer lists SN6411 heads for the 3.45:1 PI axle and the 3.7:1 carburetor axle, in mph and km/h.Medium5
What owners replace and why
Many original small gauges now come only as reconditioned exchange units, and several references are listed as no longer available. That pushes owners toward new-build Smiths gauges or rebuilt originals.Medium12
Stabilizers fail with age, and Moss sells a solid-state negative-ground replacement for the TR2-6.Medium7
Going digital without losing the look
With a mechanical tach, a digital tachometer needs a new signal wire from the coil negative or an electronic ignition tach output.
The cable can stay coiled behind the dash for a reversible fit.Low39
GPS speed removes the axle-ratio matching that the SN6411 heads need. A cable-drive sender is the alternative if you want to keep the gearbox drive.Low57
The 52 mm small gauges map directly to a 52 mm size. Feed digital gauges from a fused ignition supply rather than the pulsing stabilizer, and keep the original senders only if the new gauge reads their range.Medium28
Common faults with the original gauges
1Fuel and temperature gauges read high or move together
2Tach needle bounces or the tach is noisy
Usual causeA dry or kinked tach cable
FixReplace or lubricate the cable and route it without tight bends; RHD and LHD cars use different lengths.Low3
3Speedometer reads wrong after an axle or wheel change
Usual causeThe SN6411 head is calibrated for one axle ratio
FixFit the head for your axle (3.45:1 or 3.7:1) or have it recalibrated.Medium5
Restoration tips
Keep it original and reversible
Frequently asked
Is the TR6 tachometer mechanical?
Yes. Both the early RN2413/00A and the later RN2414/00A tachs are driven by a cable from the engine. Suppliers list cables of 42 in or 48 in for right-hand drive and 33 in or 36 in for left-hand drive. An electronic tach needs a separate signal from the ignition.Medium34
What size are TR6 small gauges?
Rimmer lists the TR6 water temperature gauge (BT2230/00) as 52 mm, and lists the same BF2232/00 fuel gauge at 52 mm. The oil pressure gauge and voltmeter share the same row of small gauges, but their size is not stated, so measure them before buying.Medium26
Does the TR6 have a voltage stabilizer?
Yes. The thermal fuel and temperature gauges run from a stabilizer that pulses battery voltage to about 10 V average. Moss sells a solid-state negative-ground replacement listed for the TR2-6 and other British cars of the period.Medium78
Did the TR6 have an ammeter or a voltmeter?
Both, depending on the series. Rimmer lists a Lucas 36427 ammeter for the CP and CC cars, and a Smiths BV2213/00 voltmeter for the later CR and CF cars.Medium12
Which TR6 speedometer do I need?
Match the axle ratio and units. Rimmer lists SN6411 heads for the 3.45:1 axle on PI cars and the 3.7:1 axle on carburetor cars, in mph or km/h, with a change at commission CF35000. The suffix on your face tells you which you have.Medium5
Related cars
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
9 sources
- Triumph TR6 small instruments, CP/CC series · Rimmer Bros · vendor-doc · retrieved 2026-11-03
- Triumph TR6 small instruments, CR/CF series · Rimmer Bros · vendor-doc · retrieved 2026-11-03
- Triumph TR6 tachometer, CP/CC series · Rimmer Bros · vendor-doc · retrieved 2026-11-03
- Triumph TR6 tachometer, CR/CF series · Rimmer Bros · vendor-doc · retrieved 2026-11-03
- Triumph TR6 speedometer, CR/CF series · Rimmer Bros · vendor-doc · retrieved 2026-11-03
- MG Midget 1500 instruments and gauges · Rimmer Bros · vendor-doc · retrieved 2026-11-03
- Triumph TR250 and TR6 dashboard and gauges · Moss Motors · vendor-doc · retrieved 2026-11-03
- MGB voltage stabilizer tech tip · Chicagoland MG Club · community · retrieved 2026-11-03
- Instructions for 80mm/100mm 12 volt Smiths Classic tachometer · Smiths Instruments (Caerbont) · vendor-doc · retrieved 2026-11-03
Markets: UK, USA, Canada, Australia, Europe. Make and model names identify the vehicle only; GAINS is not affiliated with the vehicle or instrument makers.

