Key facts
Suits
- Cars running Haltech, Link, MaxxECU, MoTeC or Syvecs ECUs that need a plug-in colour dash
- Carbureted classics and hot rods via the stand-alone Classic kit
- Builds wanting dash-side logging and a shift light in one unit
What it is and where it fits
The Haltech iC-7 is a 7 in colour dash that can replace a factory cluster or sit beside it as an extra display.
It reads engine data over CAN and adds its own sensor inputs, outputs and data logger.13
Haltech sells it as a CAN kit for cars with an ECU and as a stand-alone Classic kit for carbureted or mechanically injected cars without one. The Classic kit is aimed at hot rods, muscle cars and other classics.12
Hardware and I/O
The dash has 9 analog voltage inputs, 3 digital pulsed inputs and a tachometer input, so it can read pressure and temperature senders directly. Four digital pulsed outputs can switch warning lamps or relays.12
Fourteen programmable seven-colour LEDs form a shift-light bar across the top. Brightness follows ambient light automatically, with a manual trim.13
Haltech rates the iC-7 IP64
Dust-tight and protected against water splashes, but not against immersion or jets.12
Software and configuration
Setup uses Haltech's iC-7 software over USB.
Owners choose screens, channels, units and alarms, and the kit includes a right-angle USB to M5 cable for a tidy dash-mounted connection.13
The 512 MB onboard logger records channels from the ECU and the dash's own inputs. With Haltech Elite and Nexus ECUs, the dash can also share its I/O with the ECU.1
Connectivity and expansion
Beyond Haltech ECUs, Haltech lists plug-and-play CAN support for Link, MaxxECU, Microtech, MoTeC M1 and M400/M600/M800, and Syvecs ECUs. A separate OBD-II version reads factory ECUs.13
There is no built-in GPS. Haltech offers a GPS speed input module (HT-011310) for cars that need road speed without a wheel-speed sensor.2
Installation notes
The CAN kit ships with a 34-pin main harness with spare pins, a 3.0 m (118 in) DTM-4 CAN extension, USB cables and mounting screws. The dash surround or bracket is not listed in the kit contents.Medium13
The Classic kit adds a semi-terminated harness, a 1/8 NPT coolant sensor and two 0-150 psi (0-10.3 bar) pressure sensors. Haltech warns that wiring the coolant sensor incorrectly will damage it.2
Generations and variants
Three versions share the same dash
The CAN kit (HT-067010) for aftermarket ECUs, an OBD-II version for factory ECUs, and the stand-alone Classic kit (HT-067014) with sensors included.12
Specifications
From the maker's published data and independent sources.
Display and controls
| Spec | Value | Source |
|---|---|---|
| Screen size | 7 in (178 mm) diagonal, full colour | 12 |
| Brightness control | Ambient-light auto-dimming plus user adjustment | 13 |
| Resolution / nits | Not published on the product pagesNeither Haltech's kit pages nor the retailer list pixel resolution or brightness. | UnverifiedLow13 |
| Controls | Face-mounted buttons | 13 |
I/O and logging
Connectivity and physical
| Spec | Value | Source |
|---|---|---|
| ECU link | CAN; plug-and-play with Haltech, Link, MaxxECU, Microtech, MoTeC M1 and M400/M600/M800, Syvecs | 13 |
| Main connector | 34-pin harness with spare input pins | 13 |
| Ingress rating | IP64 (dust-tight, splash-proof) | 12 |
| Dimensions / weight | Not published on the product pageA retailer snippet gives a 217 × 122 mm case, not confirmed against a Haltech document. | UnverifiedLow1 |
Strengths and limits
Facts, each cited. Not a score.
Strengths
Often compared with
| Product | Category | Key fact |
|---|---|---|
| ECUMaster ADU 7 | Dash displays | Screen: 7 in TFT, 800 × 480, anti-glare |
| MoTeC C125 | Dash displays | Screen: 5 in TFT, 800 × 480, anti-reflective |
| AiM MXS 1.2 Strada | Dash displays | Screen: 5 in TFT, 800 × 480 (1.3 Strada) |
| AiM MXG 1.2 Strada | Dash displays | Screen: 7 in TFT, 800 × 480 (1.3 Strada) |
Frequently asked
Does the Haltech iC-7 work with other ECUs?
Yes. Haltech lists plug-and-play CAN support for Link, MaxxECU, Microtech, MoTeC M1 and M400/M600/M800, and Syvecs ECUs, alongside all current Haltech ECUs. An OBD-II version reads factory ECUs. I/O sharing, where the ECU uses the dash's inputs, works only with Haltech Elite and Nexus ECUs.13
Can the Haltech iC-7 work without an ECU?
Yes, through the stand-alone Classic kit (HT-067014). Haltech sells it for carbureted, mechanically injected or ECU-less vehicles, with a coolant sensor and two 0-150 psi pressure sensors. The dash reads them on its own analog inputs and takes rpm from its tach input.2
How many inputs does the Haltech iC-7 have?
Haltech lists 9 analog voltage inputs, 3 digital pulsed inputs and 1 tachometer input, plus 4 digital pulsed outputs. Those are in addition to every channel it receives from the ECU over CAN. The 34-pin harness has spare pins for wiring extra sensors.13
Does the Haltech iC-7 log data?
Yes. The iC-7 has 512 MB of onboard datalogging memory, according to Haltech. It can record ECU channels received over CAN and its own sensor inputs, which gives a logging path even when the ECU's own memory is small or the laptop is not connected.1
Related terms
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- HT-067010 Haltech iC-7 Digital Dash Kit product page · Haltech · vendor-doc · retrieved 2026-11-04
- HT-067014 Haltech iC-7 Stand-Alone Classic Kit product page · Haltech · vendor-doc · retrieved 2026-11-04
- Haltech iC-7 Colour Display Dash 7" (HT-067010) listing · Exo Racing (UK) · reference · retrieved 2026-11-04
A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.

