14Point7 · Wideband controllers

14Point7 Spartan 3

$139 USD without sensor; $191.50 with LSU 4.9 (maker store)

The 14Point7 Spartan 3 v2 is a compact wideband controller, priced from $139, for Bosch LSU 4.9 and LSU ADV sensors, with two programmable analog outputs, CAN bus and USB. It mounts in the engine bay, needs about five wires, and 14Point7 states 0.01 lambda accuracy without free-air calibration. The cheaper Spartan 3 Lite v2 drops CAN.12

λ
Illustration, not the product.

Key facts

SensorsBosch LSU 4.9, LSU ADV, clone LSU 4.9Sourced1
Outputs2 programmable analog + CAN + USBSourced1
Lambda range0.6-3.48.82-50 AFR gasolineSourced1
Response time10msmaker figureSourced · medium1
Price$139 (no sensor) / $191.50with LSU 4.914Point7 store prices seen November 2026.Sourced1

Suits

  • Budget builds feeding wideband to an aftermarket ECU
  • MegaSquirt, Link, Haltech or MaxxECU users wanting CAN lambda
  • Engines that want the LSU ADV sensor

What it is and where it fits

The 14Point7 Spartan 3 v2 is a bare wideband controller: it runs the oxygen sensor and outputs the reading, with no built-in display. It feeds an ECU, a data logger or a separate gauge such as 14Point7's own AFR gauge.13

It suits builds that want CAN wideband data at low cost. 14Point7 lists CAN support for MegaSquirt 3, Adaptronic, Link, Haltech, HP Tuners, YourDyno and MaxxECU.1

The Spartan 3 Lite v2 is the analog-only version, with a linear output and a simulated narrowband output but no CAN bus.2

Hardware and I/O

The v2 has two programmable analog outputs.

The first defaults to a 0-5 V linear signal for 10-20 AFR; the second defaults to heater status and can be switched to a simulated narrowband signal for a factory ECU.1

It works with the Bosch LSU 4.9, the LSU ADV and clone LSU 4.9 sensors. 14Point7 says the ADV gives 20 times the resolution of the 4.9; range runs from 0.6 to 3.4 lambda, or 0 to 21% O2.1

The unit is water, dust and dirt resistant for engine-bay mounting, rated -40 to +105 °C, with an 8 ft (2.4 m) cable. Separate heater and electronics grounds reduce noise in the reading.1

Software and configuration

Settings change over the USB serial link using a serial terminal, including which sensor is fitted.

A unit bought without a sensor ships set for the LSU 4.9.1

An output sequencer sends two precise test voltages on the main analog output. Comparing what the ECU reads against those levels lets the user build a two-point calibration of the ECU input.1

Smart heat-up modes can wait for exhaust gas to warm the sensor to 350 °C (662 °F) before the heater starts, or start heating on engine RPM over CAN with a MegaSquirt 3. A lean-burn mode covers lean-running engines.1

Connectivity and expansion

CAN output carries lambda or %O2 in formats for the ECUs and tools 14Point7 lists, with more planned through firmware updates.

The USB link also works with the Torque OBD app on Android to display AFR.1

Installation notes

Most installs need five wires for the Spartan 3 v2 and four for the Lite.

A waterproof fuse holder and two 5 A fuses come in the box.12

Bosch rates the LSU 4.9 for exhaust gas below 930 °C (1,706 °F) in normal running and lists 40 to 60 N·m (30 to 44 lbf·ft) tightening torque. 14Point7 sells weld-in sensor bungs separately.43

Generations and variants

The current models are the Spartan 3 v2, listed from June 2024, and the Spartan 3 Lite v2, listed from October 2023.

OEM board versions of both sell in bulk for integrators.Medium3

The older Spartan 2 survives as an OEM board. Lite v2 prices are $82.50 without a sensor and $135 with an LSU 4.9.32

Specifications

From the maker's published data and independent sources.

Controller (Spartan 3 v2)

SpecValueSource
Analog output 1High-performance programmable; default 0-5 V = 10-20 AFR linear1
Analog output 2Standard-performance programmable; default heater status, can be set to simulated narrowband1
CAN outputLambda or %O21
USBOn-board FTDI serial-to-USB converter1
Accuracy claim0.01 lambda with factory calibration, no free-air calibration neededMaker's claim; not independently verified.Medium1
ProcessorARM Cortex-M4; 0.1% tolerance parts in the measurement path1
GroundsSeparate heater ground and electronics ground1

Range, environment and package

SpecValueSource
Lambda range0.6 to 3.4 lambda (8.82 to 50 AFR gasoline); 0-21% O21
Operating temperature-40 to +105 °C (-40 to +221 °F)1
Cable length8 ft (2.4 m)1
SealingWater, dust and dirt resistant (no IP code published)1
In the boxController, USB converter, waterproof fuse holder, two 5 A fuses1
Warranty2 years on the controller; 3 months on the sensor1

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • Supports both LSU 4.9 and LSU ADV sensors.1
  • Two analog outputs plus CAN and USB on the v2.1
  • No free-air calibration needed, per the maker.Medium1
  • Output sequencer helps calibrate the ECU's analog input.1

Limits

  • No display; a gauge, ECU or logger must read it.1
  • Configuration is by serial terminal commands rather than a graphical tool.Medium1
  • No published IP code; described only as water, dust and dirt resistant.1
  • The Lite v2 has no CAN bus.2

Often compared with

ProductCategoryKey fact
ECUMaster Lambda to CANWideband controllersSensor: Bosch LSU 4.9
MoTeC LTC (Lambda to CAN)Wideband controllersSensor: 1 × Bosch LSU 4.9 (LTC)

Frequently asked

What is the difference between the Spartan 3 and Spartan 3 Lite?

The Spartan 3 v2 has two programmable analog outputs, CAN bus and USB. The Spartan 3 Lite v2 has a linear output and a simulated narrowband output but no CAN, and talks over UART. The Lite costs $82.50 without a sensor against $139 for the Spartan 3 v2.12

Does the Spartan 3 need free-air calibration?

14Point7 states it does not. The controller relies on extensive factory calibration and 0.1% tolerance parts, and the maker claims 0.01 lambda accuracy without free-air calibration. That figure is the maker's own and has not been independently verified here.Medium1

Which ECUs can read the Spartan 3 over CAN?

14Point7 lists MegaSquirt 3, Adaptronic, Link, Haltech, HP Tuners, YourDyno and MaxxECU, with more planned through firmware updates. The CAN output carries lambda or %O2. Other ECUs can use the analog output instead.1

Does the Spartan 3 work with the LSU ADV?

Yes. The Spartan 3 v2 supports the Bosch LSU 4.9, the LSU ADV and clone LSU 4.9 sensors. A kit with an LSU ADV costs $239. Units ordered with a sensor ship set for it; otherwise they ship set for the LSU 4.9 and can be changed over USB.1

What is the Spartan 3 analog output scale?

By default the high-performance analog output is linear, 0 to 5 V for 10 to 20 AFR. The scale is programmable. The second output defaults to heater status and can be set to a simulated narrowband signal for a factory ECU.1

Can the Spartan 3 mount in the engine bay?

Yes. 14Point7 describes the Spartan 3 v2 as durable and water-resistant for engine-bay installation, with an operating range of -40 to +105 °C. No IP code is published, so keep it away from direct exhaust heat and standing water.1

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Spartan 3 v2 product page · 14Point7 · vendor-doc · retrieved 2026-11-04
  2. Spartan 3 Lite v2 product page · 14Point7 · vendor-doc · retrieved 2026-11-04
  3. Product catalogue (store listing) · 14Point7 · vendor-doc · retrieved 2026-11-04
  4. Lambda Sensor LSU 4.9 data sheet 69034379 · Bosch Motorsport · vendor-doc · retrieved 2026-11-04

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.