Blink Marine · CAN keypads

Blink Marine PKP-2400-SI

≈ €218 (Blink online shop, configured keypad)

The Blink Marine PKP-2400-SI is a compact eight-key CAN bus keypad used in race cars to switch PDM and ECU functions without a panel of hard-wired switches. It speaks CANopen and J1939, has RGB-lit keys with interchangeable 15 mm icon inserts, is sealed to IP67 and IP69K and runs on 12 or 24 V through a four-wire connector.12

Illustration, not the product.

Key facts

Keys8, in two rows of fourSourced12
ProtocolsCANopen (DS401) and J1939Sourced2
SealingIP67 and IP69KSourced1
Supply12-24V nominal8-32 VSourced1
Weight170 g without inserts6.0 ozSourced1
Price≈ €218Blink online shop price seen November 2026; tax and icon choice may change it.Sourced · medium4

Suits

  • Race cars switching PDM channels from the dash or steering column
  • Builds that need a sealed keypad outside the cockpit
  • Mixed systems where the PDM or ECU supports CANopen keypads

What it is and where it fits

The PKP-2400-SI is an eight-key member of Blink Marine's PKP-SI keypad series.

It replaces a row of toggle switches with one sealed keypad that sends each key press over the CAN bus.1

In a race car it usually drives a power distribution module or ECU: ignition, fuel pump, fans, lights, wipers or map selection. Blink states its keypads can be fitted in the dashboard so the driver controls any PDM function or channel.3

Blink names ECUMaster, Link, Life Racing, MaxxECU, Haltech, AiM, Plex, AEM and ProEFI among the systems its keypads work with, through the standard CANopen and J1939 protocols.3

Hardware and I/O

Eight keys sit in two rows of four.

Each key has an RGB LED that backlights the icon and lights an indicator ring, so the keypad can show state as well as take input.21

The face measures about 124 × 70 mm (4.9 × 2.8 in) and the keypad weighs 170 g without inserts. It mounts on two #10-32 studs, tightened to no more than 1.0 N·m.Medium21

The keypad is sealed to IP67 and IP69K, resists UV and runs from -40 to +70 °C. Blink states it can mount inside or outside the cockpit, and a molded rear gasket keeps water out of the mounting holes.12

Software and configuration

Key behavior is set by the receiving device rather than inside the keypad.

Momentary, toggle and scroll functions, LED colors and states are configured in the PDM or ECU software that reads the keypad.Medium23

The keypad sends event messages on each press and release, periodic status of every key and a heartbeat that shows it is alive. The rates of the periodic messages are adjustable.2

Under J1939 the keypad can claim an address on its own. Blink notes this lets a spare keypad replace a failed one in the field without a laptop.2

Connectivity and expansion

A single Deutsch DT04-4P connector carries power, ground, CAN high and CAN low.

Blink also offers specific connectors and cables on request.12

Several keypads can share one bus with different addresses. The symmetrical layout and key spacing let keypads sit side by side as one larger panel.2

Installation notes

The CAN bus needs correct termination at both ends.

Check whether the receiving PDM or ECU expects CANopen or J1939 and which node address and bit rate it uses before wiring.Medium2

Icons are 15 mm inserts that swap without tools. Blink's online configurator lets buyers choose icons and order a finished keypad, and custom icons can be made.13

Generations and variants

The PKP-SI series spans several key counts; the PKP-2300-SI and PKP-2600-SI sit beside the 2400 in Blink's range.

Blink also sells PowerKey Pro, Racepad and Keybox lines aimed at motorsport.Medium31

The datasheet referenced here is revision 2, published in 2026.2

Specifications

From the maker's published data and independent sources.

Electrical and communication

SpecValueSource
Supply voltage12-24 V DC nominal, 8-32 V range1
Standby currentUnder 50 mA1
ProtocolsCANopen to device profile 401d; SAE J1939 with address claim21
MessagesEvent status, periodic status and periodic heartbeat, with adjustable rates2
Reverse polarityProtected2
MTBF238,506 hours (MIL-HDBK-217, ground mobile)1

Mechanical and environmental

SpecValueSource
ConnectorDeutsch DT04-4P, four wires (CAN low, CAN high, ground, supply)12
Key insertsInterchangeable 15 mm laser-etched inserts, LED backlit, multicolor indicator rings21
Switch life3 million operations1
OutlineAbout 124.0 × 70.3 mm (4.88 × 2.77 in) faceMedium2
MountingTwo #10-32 studs, 1.0 N·m (9 lbf·in) maximum torque21
Operating temperature-40 to +70 °C (-40 to +158 °F)1
SealingIP67 (1 m immersion for 1 hour) and IP69K (hot high-pressure spray)1
MaterialsSilicone rubber keypad with polyurethane hard coat; UV tested to UVB 400 hours1

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • Sealed to IP67 and IP69K, so it can mount outside the cockpit.1
  • Standard CANopen and J1939 protocols let it talk to many ECUs and PDMs.32
  • Runs on 8-32 V with reverse-polarity protection and a 3 million-operation switch life.12

Limits

  • Does nothing on its own; a PDM, ECU or dash must read it and define each key's function.Medium3
  • Eight keys only; larger layouts need another model or a second keypad.1
  • The receiving device must support CANopen or J1939 keypad messages.2

Often compared with

ProductCategoryKey fact
ECUMaster CAN KeyboardCAN keypadsKey layouts: 4, 6, 8, 10, 12 keys; 15-position with 2 encoders
Haltech CAN KeypadCAN keypadsLayouts: 8 buttons (2 × 4) or 15 buttons (3 × 5)

Frequently asked

What is the Blink Marine PKP-2400-SI?

It is an eight-key CAN bus keypad from Blink Marine's PKP-SI series. Each key has an RGB-lit, replaceable 15 mm icon insert, and presses go out over CAN using CANopen or J1939. Race cars use it to switch PDM and ECU functions in place of hard-wired switches.12

What protocols does the PKP-2400-SI use?

It uses CANopen, compliant with device profile 401d, and SAE J1939 with address claim. It sends event messages on each press and release, periodic status of every key and a heartbeat. The receiving PDM or ECU must support one of these protocols for the keypad.21

Is the Blink Marine keypad waterproof?

Yes. Blink rates the PKP-2400-SI to IP67, meaning dust-tight and sealed for 1 m immersion for an hour, and IP69K for hot high-pressure spray. A molded rear gasket seals the mounting holes. Blink says it can be installed inside or outside the cockpit.12

Which ECUs and PDMs work with Blink keypads?

Blink lists ECUMaster, Link, Life Racing, MaxxECU, Haltech, AiM, Plex, AEM and ProEFI among compatible systems, through the standard CANopen and J1939 protocols. Check that your specific device supports the keypad model and protocol before buying.3

How do you change the icons on a Blink keypad?

Each key takes a 15 mm laser-etched insert that pulls out and swaps without tools. Blink offers thousands of stock icons and can make custom ones. Its online configurator lets you choose icons and order a finished keypad.21

What voltage does the PKP-2400-SI run on?

Blink rates it for 12 or 24 V nominal, with an 8 to 32 V operating range and reverse-polarity protection. Standby current is under 50 mA. Power and CAN share one four-pin Deutsch DT04-4P connector.12

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.