Holley · Standalone ECUs

Holley Terminator X

Wideband controllersTransmission controllers≈ US$914 (Terminator X ECU only), ≈ US$1,300 (X MAX ECU only), ≈ US$1,600 (550-903 LS kit) at Summit Racing

The Holley Terminator X is an engine-specific EFI system for LS, LT, Coyote and Gen V Hemi swaps that drives 8 high-impedance injectors and 8 coils, with a built-in Bosch LSU 4.9 wideband controller, 1 bar MAP sensor, 2 knock channels and 4 programmable inputs and outputs. The X MAX version adds drive-by-wire and 4L60E/4L80E/4R70W transmission control. Kits include a 3.5 in handheld.Medium123

Illustration, not the product.

Key facts

Injectors / coils8 high-impedance / 8Sourced12
Programmable I/O4 inputs + 4 outputsSourced12
Wideband1 channel, Bosch LSU 4.9 onlySourced12
Drive-by-wireX MAX only1 channelSourced12
Transmission controlX MAX only: 4L60-E, 4L80-E, 4R70WSourced2
Price (ECU only)≈ US$914 (X) / ≈ US$1,300X MAXSourced · medium12

Suits

  • LS, LT, Coyote and Gen V Hemi swaps in street cars and hot rods
  • Owners who want a handheld setup wizard instead of a laptop
  • Swaps keeping a 4L60-E, 4L80-E or 4R70W automatic (X MAX)

What it is and where it fits

The Holley Terminator X is an EFI system sold mainly as engine-specific kits, aimed at V8 swaps and hot rods rather than race cars with complex I/O. Summit lists dozens of kits and service ECUs under the Terminator X and Terminator X MAX names.Medium43

Kits such as the 550-903 for LS1 and LS6 engines include the ECU, a 3.5 in touchscreen handheld and a wideband sensor, so a basic install needs no laptop. The base version runs a cable throttle; the X MAX adds drive-by-wire and automatic transmission control.32

Hardware and I/O

Both versions drive 8 high-impedance injectors and 8 coils, with 2 knock channels, an integrated 1 bar MAP sensor and one Bosch LSU 4.9 wideband channel. Low-impedance injectors and LSU 4.2 sensors are not supported.123

Four programmable inputs and four outputs handle extra pressure sensors, a trans-brake or nitrous trigger, fans, boost solenoids and idle valves. Fuel and oil pressure inputs come pre-terminated.12

Software and configuration

Setup runs through the handheld's wizard or Holley's free EFI tuning software on a laptop.

The handheld wizard includes OEM injector data, which shortens first start-up on stock injectors.23

Functions include boost control by time, gear, rpm or speed, one nitrous stage, engine protection and flex fuel with a separately bought sensor. Traction control, launch control, VVT and multi-fuel are not supported.123

Connectivity and expansion

One CAN network connects Holley displays and accessories.

Summit also lists a replacement Terminator X Bluetooth module, which points to phone connectivity on some kits.Medium14

Data logging is built in. Summit lists the X and X MAX service ECUs as compatible with all Terminator X harnesses, so a failed unit can be replaced without rewiring.Medium12

Installation notes

Each kit matches a trigger and sensor set.

The 550-903, for example, suits LS1 and LS6 engines with a 24x crank, 1x cam, 1 bar MAP and EV1 injector connectors, and it will not operate displacement-on-demand hardware.3

Boosted engines need an external MAP sensor because the internal unit reads only 1 bar. Fuel system work carries fire risk: depressurize the system, use fuel-rated hose and fittings, and keep a fire extinguisher nearby.Medium1

Generations and variants

Terminator X (ECU 554-152, about US$914) runs a cable throttle without transmission control.

Terminator X MAX (ECU 554-153, about US$1,300) adds one drive-by-wire channel and control of the 4L60-E, 4L80-E and 4R70W automatics.12

Holley also sells Terminator X Stealth 4150 throttle-body systems that mount on a carburetor flange.Medium4

Specifications

From the maker's published data and independent sources.

Engine control

SpecValueSource
Injector drivers8, high-impedance only (no low-impedance support)31
Coil outputs812
Knock control2 channels12
MAP sensorIntegrated 1 bar; can be disabled for an external sensor on boosted engines12
Wideband1 channel, Bosch LSU 4.9 (not LSU 4.2)12

I/O and functions

SpecValueSource
Programmable inputs4 (12 V, ground, 5 V, frequency); fuel and oil pressure pre-terminated12
Programmable outputs4 (ground, PWM) for fans, boost, nitrous, idle valve12
Boost / nitrousBoost control by time, gear, rpm or speed; 1 nitrous stage23
Not supportedTraction control, launch control, VVT, multi-fuel12
CAN1 network12

X MAX additions

SpecValueSource
Drive-by-wire1 channel; GM LS/LT, Ford Coyote and Mopar Gen V throttle bodies2
Transmission controlGM 4L60-E, 4L80-E and Ford 4R70W2
Diagnostic LEDs8 multi-colour2

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • Engine-specific kits include a handheld controller with a setup wizard.32
  • Built-in LSU 4.9 wideband controller.1
  • X MAX controls common GM and Ford automatics without a separate TCU.2
  • ECU-only service units cost about US$914 (X) and US$1,300 (X MAX).Medium12

Limits

  • High-impedance injectors only.31
  • No traction control, launch control or VVT.12
  • Internal MAP sensor reads 1 bar; boost needs an external sensor.12
  • Only four programmable inputs and outputs.1

Often compared with

ProductCategoryKey fact
FuelTech FT600Standalone ECUsInjector outputs: 16 (up to 4 high-impedance injectors each)
Haltech Elite 2500Standalone ECUsInjector / ignition outputs: 8 / 8
Haltech Nexus R5 VCUStandalone ECUsInjector / ignition outputs: 18 / 12
ECUMaster EMU BlackStandalone ECUsInjectors: Up to 8 high-impedance sequential (6 dedicated outputs + aux)

Frequently asked

What is the difference between Terminator X and Terminator X MAX?

The X MAX adds one drive-by-wire channel for GM LS/LT, Ford Coyote and Mopar Gen V throttle bodies, and transmission control for the 4L60-E, 4L80-E and 4R70W. The base Terminator X runs a cable throttle with no transmission control. Both share injector, coil, wideband and I/O counts.12

Does Holley Terminator X support drive-by-wire?

Only the X MAX version. Summit lists the base Terminator X ECU as not drive-by-wire capable, while the X MAX ECU has one channel for GM LS and LT, Ford Coyote and Mopar Gen V throttle bodies. Engines with electronic throttles need X MAX hardware or a cable throttle conversion.12

Can Terminator X control a 4L60E?

The Terminator X MAX can. Summit lists transmission control for the GM 4L60-E and 4L80-E and the Ford 4R70W on the X MAX ECU. The base Terminator X does not include transmission control, though its programmable inputs can read a trans-brake switch.21

Does the Terminator X have a wideband?

Yes. Both versions have one wideband channel for a Bosch LSU 4.9 sensor and will not work with LSU 4.2 sensors. Some kits include the sensor, such as the 550-903 LS kit, while the ECU-only service units do not. Mount the sensor upstream of the catalytic converter.123

Can the Terminator X run boost?

Yes, with an external MAP sensor. The internal sensor reads only 1 bar, so boosted engines disable it and use an external sensor. Boost control by time, gear, rpm or speed is built in, with safeties. Launch control and traction control are not supported.12

Can Terminator X run low-impedance injectors?

No. Summit's listing for the 550-903 kit states it will not control low-impedance injectors, and the ECU listings describe high-impedance drivers. Large race injectors that are low impedance need a different ECU or an external peak-and-hold driver. Check the injector data sheet before ordering.31

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. Holley Terminator X Engine Control Module 554-152 · Summit Racing Equipment · reference · retrieved 2026-11-04
  2. Holley Terminator X MAX Engine Control Module 554-153 · Summit Racing Equipment · reference · retrieved 2026-11-04
  3. Holley Terminator X Engine Management System 550-903 (LS1/LS6) · Summit Racing Equipment · reference · retrieved 2026-11-04

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.