Haltech · Standalone ECUs

Haltech Nexus R5 VCU

Power distribution modulesWideband controllersData loggersTransmission controllers≈ US$4,415 list, ≈ US$3,970 special (Haltech, excl. tax)

The Haltech Nexus R5 is a vehicle control unit that combines a standalone ECU with 18 injector and 12 ignition outputs, a 16-output power distribution module, two onboard wideband controllers and a 512 MB data logger in one box. It suits high-output builds that would otherwise need a separate PDM, wideband and logger, and it can also run several automatic transmissions.13

Illustration, not the product.

Key facts

Injector / ignition outputs18/ 12Sourced12
Power outputs4 × 25 A + 12 × 8 A continuousSourced12
Analog inputs23 × 0-5VSourced12
Onboard wideband2channelsNTK and Bosch LSU 4.9Sourced12
Logging300 channels at up to 1 kHz, 512 MBSourced1
List price≈ US$4,415≈ US$3,970 specialSourced · medium1

Suits

  • High-output V8 and swap builds that would otherwise add a PDM, two wideband controllers and a logger
  • Drag cars running a supported automatic with trans-brake
  • Builds with twin electronic throttles or more than 8 injectors

What it is and where it fits

The Haltech Nexus R5 is the company's flagship vehicle control unit (VCU).

It merges an engine ECU, a power distribution module, two wideband controllers and a data logger into one housing.13

Street Machine chose one for a high-power VS Commodore ute build and noted the payoff: fewer separate boxes, relays, adaptors and wiring runs. The R5 targets builds where those extra modules would otherwise add cost and clutter.Medium3

Hardware and I/O

Eighteen peak-and-hold injector drivers allow staged fuel on a V8 or sequential fuel on large engines.

Twelve ignition outputs drive smart coils or an external igniter, and spare channels can switch as low-side outputs.1

The power side has 4 push-pull outputs rated 25 A continuous and 12 high-side outputs rated 8 A continuous. These replace relays for fuel pumps, fans and water pumps, with PWM for speed control.12

Inputs include 23 analog channels, 10 synchronized pulsed inputs and 2 knock channels. There is no internal MAP sensor, so the build needs an external sensor plumbed to the manifold.1

Software and configuration

Configuration uses Haltech's NSP software.

Fuel and ignition tables reach 32 × 32 with an 8-deep fourth axis, and long-term learning trims fuel up to a 4D table.1

Feature support covers dual drive-by-wire, up to 4 variable cams, launch, anti-lag, traction control, 6-stage nitrous and torque management. Haltech also lists automatic transmission control for the Ford AODE/4R70W, GM 4L60E and 4L80E and Toyota A340E, plus Lenco and Liberty gearboxes.1

Connectivity and expansion

Three CAN buses with switchable termination feed dashes, keypads and expansion modules.

Onboard Wi-Fi links the unit to Haltech's phone app, and a USB-C port handles laptop tuning.1

The 512 MB logger records up to 300 channels at up to 1 kHz. A built-in G-sensor adds acceleration channels without a separate module.1

Installation notes

Because the R5 switches 25 A loads itself, its supply and ground wiring must be sized for the total current.

Fuse the main feed close to the battery and route high-current wires away from sensor signals.Medium1

Haltech and dealers sell universal wire-in and engine-specific terminated harnesses. In the Street Machine build, the team made a steel bracket to mount the R5 under the dash and mocked up an LS terminated harness before final routing.Medium32

Generations and variants

The R5 sits above Haltech's smaller Nexus models and the older Elite ECUs.

Compared with the Elite 2500, it adds onboard wideband, PDM outputs, Wi-Fi, a third CAN bus and far larger logging memory.14

Specifications

From the maker's published data and independent sources.

Outputs

SpecValueSource
Injector drivers18 peak and hold (also usable as low-side outputs)12
Ignition outputs12 low-current (also usable as low-side outputs)1
High-current outputs4 × 25 A continuous, push-pull, PWM to 5 kHz12
High-side outputs12 × 8 A continuous, PWM to 200 Hz12
Digital pulsed outputs8 low-side, PWM capable1
Half-bridge outputs4 × 8 A push-pull / H-bridge (e.g. two electronic throttles)1

Inputs

SpecValueSource
Analog voltage inputs23 × 0-5 V, switchable 5 V pull-up12
Engine position2 differential (trigger and home), adjustable thresholds1
Synchronized pulsed inputs10 (cam, frequency or 0-5 V)12
Knock inputs21
MAP sensorExternal (not built in)1
Inertial sensorBuilt-in G-sensor1

Communication and logging

SpecValueSource
CAN3 buses, switchable termination12
PC linkUSB 2.0 over USB-C; can power up over the cable1
Wi-FiOnboard, antenna included; works with Haltech's phone app1
LoggingUp to 300 channels at up to 1 kHz (1 ms), 512 MB1

Physical

SpecValueSource
ConnectorsSurLok-style red and black connectors (pin counts not published on the product page)Medium12
Dimensions and weightNot published on the product pageOne retailer lists only shipping-box size and weight, not the unit.UnverifiedLow2

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • Sixteen switched power outputs (4 × 25 A, 12 × 8 A) can replace a separate PDM and most relays.1
  • Two onboard wideband controllers accept NTK or Bosch LSU 4.9 sensors, so no external lambda modules are needed for two banks.12
  • Logs up to 300 channels at 1 kHz into 512 MB of onboard memory.1
  • Runs several common automatic transmissions without a separate controller.1

Limits

  • No internal MAP sensor; an external sensor is required.1
  • List price of about US$4,415 is more than double the Elite 2500's US$1,959.Medium14
  • Ignition outputs are low-current logic drives, so passive coils need an external igniter (inferred from the output type).Medium1
  • Unit dimensions and weight are not published on the product page.Medium12

Often compared with

ProductCategoryKey fact
Haltech Elite 2500Standalone ECUsInjector / ignition outputs: 8 / 8
Link G5 Voodoo Neo 6Standalone ECUsInjection / ignition drives: 12 / 8
MoTeC M150Standalone ECUsInjector outputs: 12 peak and hold + 6 low-side
Emtron KV8Standalone ECUsInjector / ignition outputs: 8 / 8
Syvecs S7-PlusStandalone ECUsInjection / PWM outputs: 16 low-side, 10 A max each
MaxxECU RACEStandalone ECUsInjector / ignition outputs: 8 peak and hold (8 A) / 8
FuelTech FT600Standalone ECUsInjector outputs: 16 (up to 4 high-impedance injectors each)
Haltech PD16 PDMPower distribution modulesOutputs: 16 (10 high-side, 2 half-bridge, 4 × 25 A)

Frequently asked

What is the Haltech Nexus R5?

The Nexus R5 is Haltech's flagship vehicle control unit. It combines an engine ECU with 18 injector and 12 ignition outputs, a power distribution module with 16 switched outputs, two wideband controllers and a 512 MB logger. The aim is to replace several separate boxes with one unit and one harness.13

Does the Nexus R5 have a built-in PDM?

Yes. Haltech lists an onboard PDM with 4 push-pull outputs rated 25 A continuous and 12 high-side outputs rated 8 A continuous. That covers fuel pumps, fans and water pumps directly. Very large load counts may still need a separate PDM on the CAN bus.12

Does the Nexus R5 have a built-in wideband controller?

Yes, two. The R5 has two onboard wideband controllers that support NTK and Bosch LSU 4.9 sensors. That allows closed-loop lambda control on each bank of a V engine without separate CAN wideband modules, which saves wiring and mounting space.12

Can the Nexus R5 control an automatic transmission?

Yes, for listed gearboxes. Haltech names the Ford AODE and 4R70W, GM 4L60E and 4L80E, and Toyota A340E, plus Lenco and Liberty drag transmissions. Other electronic automatics need a separate transmission controller or confirmation from Haltech before purchase. Check the gear count and solenoid type of your exact gearbox first.1

Does the Nexus R5 have a MAP sensor inside?

No. Haltech lists the MAP sensor as external on the R5, unlike the Elite 2500's internal 4 bar sensor. Choose a sensor range that covers your peak boost with margin and mount it with a short, dry vacuum line from the plenum.14

How is the Nexus R5 different from the Elite 2500?

The R5 adds 10 injector outputs, 4 ignition outputs, onboard wideband, PDM outputs, Wi-Fi, a third CAN bus and a G-sensor. Logging rises from 40 channels at 200 Hz to 300 channels at 1 kHz. The trade-off is a list price more than twice as high.14

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. HT-195000 Nexus R5 VCU product page · Haltech · vendor-doc · retrieved 2026-11-04
  2. Haltech Nexus R5 VCU (HT-195000) listing · Possum Bourne Motorsport (NZ) · reference · retrieved 2026-11-04
  3. Video: Installing a Haltech Nexus R5 (16 February 2024) · Street Machine · press · retrieved 2026-11-04
  4. HT-151300 Elite 2500 ECU product page · Haltech · vendor-doc · retrieved 2026-11-04

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.