Emtron · Standalone ECUs

Emtron KV8

Wideband controllersData loggers≈ A$4,400 (Emtron Australia)

The Emtron KV8 is an Australian motorsport ECU with 8 injector channels (peak-and-hold or saturated), 8 ignition outputs, 16 auxiliary outputs, 16 analog and 14 digital inputs, two onboard Bosch LSU 4.9 wideband controllers, dual drive-by-wire, 2 CAN buses and Ethernet, in a 730 g billet case. Emtron Australia lists it at about A$4,400.1

Illustration, not the product.

Key facts

Injector / ignition outputs8/ 8Sourced1
Auxiliary outputs168 low/high side + 8 half-bridgeSourced1
Inputs16 analog + 14 digital + 2 crank/sync + 2 knockSourced1
Wideband2 onboard Bosch LSU 4.9Sourced1
Logging32 MB, 1,200+ channels, 1-500 HzSourced1
Size / weight134 × 162 × 27mm, 730 gSourced1

Suits

  • Eight-cylinder or smaller race engines needing two widebands and two throttles
  • Builders who want selectable injector drive and detailed knock filtering
  • Installs with little mounting depth, given the 27 mm case

What it is and where it fits

The Emtron KV8 is an eight-channel motorsport ECU from Emtron.

It handles up to eight cylinders with one injector and one coil each, and adds two wideband controllers, dual drive-by-wire and an onboard accelerometer.1

Its specification targets builders who want fine control of injector drive, knock filtering and auxiliary outputs, with a 27 mm thin case for tight mounting spaces.Medium1

Hardware and I/O

Each injector channel runs peak-and-hold for injectors under 5 Ω (8 A peak, 4 A hold) or saturated drive above 5 Ω.

Unused injector channels work as auxiliary outputs at up to 5 kHz.1

Sixteen auxiliary outputs split into 8 low- or high-side drivers and 8 half-bridges. Aux 9-12 can pair into H-bridges for two electronic throttles, and aux 13-16 carry 15 A continuous each.1

Inputs total 16 analog, 14 digital and 2 crank/sync channels. Knock sensing uses a Bosch digital knock chip with a programmable filter, and a barometric sensor and accelerometer sit on the board.1

Software and configuration

Tuning runs over 100 Mbps Ethernet.

A built-in four-channel oscilloscope sampling at 100,000 samples per second helps diagnose crank, cam and other signals without separate test gear.1

Variable cam position inputs run on digital inputs 1-4, and knock filtering is configurable by center frequency, bandwidth, window and gain.1

Connectivity and expansion

Two CAN 2.0B buses run at 1 Mbps.

Third-party dashes list Emtron support, including ECUMaster's ADU range.12

Onboard logging stores 32 MB across more than 1,200 channels at 1-500 Hz. Longer sessions at high rates may suit a logging dash as well.Medium1

Installation notes

Emtron uses 120-way Superseal connectors with gold-plated 1 mm pins rated to 15 A each, depending on wire gauge.

Reverse battery protection relies on an external fuse, so fuse the supply as Emtron specifies.1

Recommended operating temperature is -30 to 85 °C. Ignition outputs drive at 35 or 70 mA, so use coils with built-in igniters or an external ignition module.1

Generations and variants

Emtron's product page covers the KV8 under part 1122-082 and does not describe earlier hardware revisions.

Compare it with the rest of Emtron's range on the maker's site before choosing.Medium1

Specifications

From the maker's published data and independent sources.

Outputs

SpecValueSource
Injector channels8; peak and hold below 5 Ω (8 A peak, 4 A hold) or saturated above 5 Ω1
Ignition outputs8 low-side, 35 or 70 mA drive (for igniters or smart coils)1
Aux 1-8Low or high side; 4 A or 2.5 A continuous low side, 4 A high side; to 15 kHz1
Aux 9-16Half-bridge; 9-12 at 5 A (H-bridge for drive-by-wire), 13-16 at 15 A1
Sensor supplies2 × 5.0 V at 0.4 A, 1 × 8.0 V at 0.6 A1

Inputs

SpecValueSource
Analog inputs16, 12-bit, 0-5 V; 6 usable as 2-wire thermistor inputs1
Digital inputs14 (DI 1-8 frequency to 30 kHz; VVT position on DI 1-4)1
Crank / sync inputs2; magnetic, Hall/optical or logic; up to ±80 V1
Knock inputs2 differential, Bosch digital knock IC with programmable filter1
Lambda2 onboard Bosch LSU 4.9 controllers, 0.58-10.0 λ1
Onboard sensorsBarometric (40-115 kPa) and 3-axis accelerometer1

Processing, communication and logging

SpecValueSource
ProcessorsDual 100 MHz, 500 MB RAM1
Logging32 MB, 1,200+ channels, 1-500 Hz1
Oscilloscope4 channels at 100,000 samples per second1
PC link100 Mbps Ethernet1
CAN2 × CAN 2.0B at 1 Mbps1

Physical

SpecValueSource
Enclosure6061 CNC billet aluminum1
Dimensions134 × 162 × 27 mm (5.3 × 6.4 × 1.1 in)1
Weight730 g (1.6 lb)1
Connectors120-way Superseal, gold-plated 1 mm pins, up to 15 A per pin1
Supply / temperature6-22 V DC (shuts down at 24 V); -30 to 85 °C recommended1
IP ratingNot published on the product pageEmtron lists the billet case but no IP code.UnverifiedLow1

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • Injector drive switches between peak-and-hold and saturated per channel.1
  • Two onboard Bosch LSU 4.9 wideband controllers.1
  • Sixteen aux outputs, including four 15 A half-bridges.1
  • Built-in four-channel oscilloscope at 100,000 samples per second.1

Limits

  • 32 MB of logging memory, small next to 512 MB to 1 GB on some rivals.13
  • Reverse battery protection depends on an external fuse.1
  • Ignition outputs are low-current logic drives that need igniters.1
  • No IP rating published on the product page.Medium1

Often compared with

ProductCategoryKey fact
MoTeC M150Standalone ECUsInjector outputs: 12 peak and hold + 6 low-side
Syvecs S7-PlusStandalone ECUsInjection / PWM outputs: 16 low-side, 10 A max each
Haltech Nexus R5 VCUStandalone ECUsInjector / ignition outputs: 18 / 12
Link G5 Voodoo Neo 6Standalone ECUsInjection / ignition drives: 12 / 8
ECUMaster EMU PRO-8Standalone ECUsOutputs / inputs: 31 / 24
MaxxECU RACEStandalone ECUsInjector / ignition outputs: 8 peak and hold (8 A) / 8

Frequently asked

How many cylinders can the Emtron KV8 run?

The KV8 has 8 injector channels and 8 ignition outputs, so it runs up to eight cylinders with one injector and one coil each. Unused injector and ignition channels can switch auxiliary loads, which suits four- and six-cylinder engines with many actuators.1

Does the Emtron KV8 have built-in wideband?

Yes, two channels. Emtron lists two onboard Bosch LSU 4.9 wideband controllers measuring 0.58 to 10.0 lambda, with Nernst cell temperature measurement. That allows closed-loop control per bank on a V engine without external lambda modules. Each sensor still needs its own heater wiring run.1

How much logging does the Emtron KV8 have?

Emtron lists 32 MB of logging memory, more than 1,200 loggable channels and rates from 1 to 500 Hz. That is less memory than some newer ECUs, so heavy high-rate logging over long sessions may need careful channel selection or a logging dash.1

Can the Emtron KV8 run peak-and-hold injectors?

Yes. Each injector channel runs peak-and-hold for injectors under 5 Ω, at 8 A peak and 4 A hold, or saturated drive for injectors above 5 Ω. Both modes have a 70 V flyback clamp, so low-impedance race injectors need no external driver box.1

How does the Emtron KV8 connect to a laptop?

The KV8 uses a 100 Mbps Ethernet link for its tuning software, according to Emtron. Two CAN 2.0B buses at 1 Mbps handle dashes and expansion devices. Build an Ethernet connection into the harness at a convenient point for tuning and log downloads.1

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. KV8 product page and specifications (SKU 1122-082) · Emtron Australia · vendor-doc · retrieved 2026-11-04
  2. ADU product page (ECU compatibility list) · ECUMaster · vendor-doc · retrieved 2026-11-04
  3. HT-195000 Nexus R5 VCU product page · Haltech · vendor-doc · retrieved 2026-11-04

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.