MaxxECU · Standalone ECUs

MaxxECU RACE

Wideband controllersData loggers≈ $1,590 unit only, ≈ $1,863 standard kit, ≈ $2,008 premium kit (MaxxECU, excl. VAT)

The MaxxECU RACE is a standalone ECU with 8 peak-and-hold injector outputs, 8 ignition outputs, a built-in Bosch LSU 4.2/4.9 wideband controller, a 3 bar boost-capable MAP sensor, 8 EGT inputs and 8 MB of logging at up to 1,000 Hz. It runs up to 8 cylinders sequentially and suits turbo street and race builds; a waterproof H2O version is also sold.1

Illustration, not the product.

Key facts

Injector / ignition outputs8 peak and hold (8 A) / 8Sourced1
Built-in wideband1 channel, Bosch LSU 4.2 / 4.9Sourced1
EGT inputs8× type K/NSourced1
Logging8 MB internal at up to 1,000 HzSourced12
Size / weight155 × 195 × 40mm, 880 gSourced1
Price≈ $1,590 unit onlyexcl. VATSourced · medium1

Suits

  • Four- and six-cylinder turbo builds wanting wideband, MAP and EGT inputs onboard
  • V8s with one wideband and per-cylinder EGT
  • Wet-mount installs using the H2O version

What it is and where it fits

The MaxxECU RACE sits below the larger PRO in MaxxECU's line, which also includes MINI and STREET models.

It runs 1-12 cylinder two- and four-stroke engines, sequentially up to 8 cylinders or up to 12 in wasted spark.12

The feature list targets turbo builds

Anti-lag, launch, rolling launch, shift cut, traction control, flex fuel, VVT and EGT-based protection. Sequential gearbox control and CAN-based transmission control are also listed.1

Hardware and I/O

Eight peak-and-hold injector outputs rated 8 A each can drive one or two injectors per output, high or low impedance.

Ignition outputs send a 5 V signal, so passive coils need an igniter module.1

A built-in Bosch LSU wideband controller and a MAP sensor good for 3 bar (43.5 psi) of boost save two external boxes. Eight thermocouple EGT inputs on a separate harness allow per-cylinder exhaust temperature on a V8.1

The page's highlights and detailed spec disagree on some counts: 8 versus 6 extra analog inputs and 2 versus 4 throttle motor outputs. This page uses the detailed figures and flags both.Medium1

Software and configuration

Tuning uses MaxxECU's MTune software over USB.

A built-in trigger oscilloscope and trigger logger help diagnose crank and cam signals during setup.1

MaxxECU quotes 0.1° ignition resolution and 0.001 ms injector resolution, with fuel and ignition recalculated 2,000 times per second. Analog inputs sample at up to 1,000 Hz.1

Connectivity and expansion

The CAN bus carries transmission control, expansion modules, OEM vehicle CAN and OBD-II.

Built-in Bluetooth links to MaxxECU's MDash phone app.1

Internal logging is 8 MB at up to 1,000 Hz, the same figure the larger PRO lists. Laptop logging runs at 20 Hz, so high-rate data should come from the internal log.12

Installation notes

MaxxECU sells the RACE as a bare unit or in kits with harnesses and Molex connectors.

The page notes that harness 2 is needed for all functions on the standard kit, and EGT inputs use a separate harness.1

Supply voltage is 8-22 V. Use the H2O version when the ECU must live in a wet location, since the standard unit is not described as waterproof.Medium1

Generations and variants

The RACE comes in standard and H2O (waterproof) versions.

MaxxECU also sells a newer GEN2 RACE, offered in plug-in kits with Bosch LSU 5.2 sensors for Audi ME7.x and BMW M54 engines; its full I/O is not on that page.Medium13

The PRO model steps up to 16 injector outputs, 12 ignition outputs, dual wideband and dual CAN in a 1,137 g case.2

Specifications

From the maker's published data and independent sources.

Outputs

SpecValueSource
Injector outputs8 peak and hold, 8 A, 1-2 high- or low-impedance injectors each1
Ignition outputs8 × 5 V logic (for modules, CDI or smart coils)1
Low-side outputs9 (8 × 2 A, 1 × 5 A)1
+12 V outputs2 × 2 A1
Motor outputs4 × 2 A (also used for electronic throttle)The detailed spec lists 4 motor outputs; the page's highlights mention 2 extra outputs for E-Throttle.Sources differMedium1

Inputs

SpecValueSource
Dedicated sensor inputsIAT, CLT, TPS, wideband1
Extra analog inputs6 × 0-5 VThe detailed spec lists 6; the highlights list 8 extra analog inputs.Sources differMedium1
Extra temperature inputs2 (usable as switches)1
Trigger inputs2, VR or digital, automatic level detection1
Extra digital/VR inputs41
Knock inputs21
EGT inputs8 × type K/N, up to 1,200 °C (2,200 °F), separate harness, 50 Hz1
MAP sensorBuilt in, up to 3 bar (43.5 psi) boost1

Communication, processing and physical

SpecValueSource
CAN1 bus listed (transmission, expansion, OEM CAN, OBD-II)Medium1
PC / phone linkUSB (MTune software); Bluetooth for the MDash app1
ProcessorARM Cortex-M3 at 120 MHz plus 3 helper processors; fuel and ignition updated 2,000 times per second1
Supply voltage8-22 V1
Dimensions / weight155 × 195 × 40 mm (6.1 × 7.7 × 1.6 in) incl. mounts; 880 g1
Ingress ratingH2O version described as waterproof; no IP code publishedMaxxECU gives no IP code for either version on the product page.UnverifiedLow1

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • Built-in wideband controller and 3 bar MAP sensor.1
  • Eight EGT inputs for per-cylinder exhaust temperature on up to eight cylinders.1
  • Peak-and-hold injector drivers handle low-impedance injectors without resistor packs.1
  • Bluetooth link to a phone app without extra hardware.1

Limits

  • One wideband channel; dual-bank closed loop needs the PRO or an external controller.12
  • Internal logging memory is 8 MB.1
  • Ignition outputs are 5 V logic, so passive coils need an igniter.1
  • Product page gives conflicting counts for analog inputs and throttle outputs.1

Often compared with

ProductCategoryKey fact
Link G4X FuryXStandalone ECUsInjection drivers: 8
ECUMaster EMU BlackStandalone ECUsInjectors: Up to 8 high-impedance sequential (6 dedicated outputs + aux)
ECUMaster EMU PRO-8Standalone ECUsOutputs / inputs: 31 / 24
Haltech Elite 2500Standalone ECUsInjector / ignition outputs: 8 / 8
FuelTech FT600Standalone ECUsInjector outputs: 16 (up to 4 high-impedance injectors each)

Frequently asked

Does the MaxxECU RACE have a built-in wideband controller?

Yes. The RACE has one built-in wideband controller that accepts Bosch LSU 4.2 and LSU 4.9 sensors. Premium kits include an LSU 4.2. For a second wideband channel on a V engine, MaxxECU's PRO has dual wideband, or an external controller can feed the CAN bus.12

How many cylinders can the MaxxECU RACE run sequentially?

Up to 8 cylinders fully sequential, using its 8 injector and 8 ignition outputs. MaxxECU lists support for engines up to 12 cylinders using wasted spark, and each 8 A injector output can drive one or two injectors for batch or paired operation.1

What is the MaxxECU RACE H2O?

It is the waterproof version of the RACE, sold at a small premium: about $1,728 unit only against about $1,590 for the standard unit, excluding VAT. MaxxECU does not publish an IP code, so confirm the rating if the ECU will see direct spray.1

What is the difference between the MaxxECU RACE and PRO?

The PRO has 16 injector outputs, 12 ignition outputs, about 30 general outputs, dual wideband, dual CAN and 12 EGT inputs, and weighs 1,137 g. The RACE has 8 injector and 8 ignition outputs, one wideband, 8 EGT inputs and weighs 880 g. Both log 8 MB at up to 1,000 Hz.12

What software does MaxxECU use?

MaxxECU ECUs are tuned with the company's MTune software over USB. The RACE also has built-in Bluetooth for the MDash app, which shows live data on a phone. MTune includes a trigger oscilloscope for checking crank and cam signals during setup.1

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. MaxxECU RACE product page · MaxxECU · vendor-doc · retrieved 2026-11-04
  2. MaxxECU PRO product page · MaxxECU · vendor-doc · retrieved 2026-11-04
  3. MaxxECU GEN2 RACE product page · MaxxECU · vendor-doc · retrieved 2026-11-04

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.