Key facts
- 8 in the spec list
- 6 in the description
Suits
- Four- and six-cylinder turbo builds wanting wideband and drive-by-wire in one wire-in box
- Motorsport cars needing launch, traction and gear-shift control
- Builders with an existing Link loom or third-party G4X harness
What it is and where it fits
The Link G4X FuryX is the wire-in G4X model with an onboard wideband controller.
Link's G4X wire-in range also includes the AtomX, MonsoonX, StormX and XtremeX.Medium1
Link describes it with the full motorsport feature set: traction control, launch control, anti-lag, gear-shift control and cruise control. The X suffix marks the G4X generation, which the retailer says communicates faster than the older G4+ models.1
Hardware and I/O
Eight injection drivers allow sequential fuel on up to eight cylinders.
The retailer lists 8 ignition drivers in its spec table but 6 in its description; check the exact count with a dealer before planning an eight-coil install.Medium1
Ten auxiliary outputs handle pumps, fans, solenoids and the electronic throttle, and unused fuel or ignition drivers can be repurposed as extra aux outputs. Inputs total 11 analog, 4 temperature, up to 10 digital, 2 trigger and 2 knock.1
The die-cast aluminum case measures 185 × 130 × 40 mm (7.3 × 5.1 × 1.6 in) without looms and weighs 680 g. Link supplies a mounting bracket.21
Software and configuration
Tuning uses Link's PCLink software over USB.
The FuryX offers 30 general-purpose tables, up from 20 on the StormX, plus an advanced closed-loop lambda strategy with dual-bank control.1
Electronic throttle control is fully programmable, including a throttle blip on downshifts and an anti-lag mode.1
Connectivity and expansion
Two independent CAN buses connect dashes, keypads and expansion modules, though the second bus uses two of the digital inputs.
One RS232 port and 512 MB of onboard logging complete the communications.1
Haltech lists Link ECUs among those its iC-7 dash reads plug-and-play over CAN, which shows the kind of third-party dash support available.Medium4
Installation notes
The ECU ships without wiring.
Buyers add Link's A and B looms or pin kits, or a third-party terminated harness, which adds to the box price.1
Mount the case on the supplied bracket, keep the wideband sensor lead away from ignition wiring and fuse every high-current load. The second CAN bus costs two digital inputs, so plan input use early.Medium21
Generations and variants
The X models are the G4X generation, which succeeded G4+ and communicates faster, according to the retailer.
Link's newer G5 Voodoo family adds onboard GPS, Wi-Fi and Ethernet, and the Voodoo Neo 6 lists 1 GB of logging, double the FuryX.Medium13
Specifications
From the maker's published data and independent sources.
Outputs
Inputs
Communication and logging
Strengths and limits
Facts, each cited. Not a score.
Strengths
Often compared with
| Product | Category | Key fact |
|---|---|---|
| Link G5 Voodoo Neo 6 | Standalone ECUs | Injection / ignition drives: 12 / 8 |
| Haltech Elite 2500 | Standalone ECUs | Injector / ignition outputs: 8 / 8 |
| ECUMaster EMU PRO-8 | Standalone ECUs | Outputs / inputs: 31 / 24 |
| MaxxECU RACE | Standalone ECUs | Injector / ignition outputs: 8 peak and hold (8 A) / 8 |
| MoTeC M130 | Standalone ECUs | Injector / ignition outputs: 8 / 8 |
| Emtron KV8 | Standalone ECUs | Injector / ignition outputs: 8 / 8 |
Frequently asked
Does the Link FuryX have a built-in wideband?
Yes. The FuryX has an onboard digital wideband lambda controller and an advanced closed-loop lambda strategy with dual-bank control. A second bank's sensor needs an extra controller, typically on CAN. The onboard channel removes one external box and its wiring on most four- and six-cylinder builds.Medium1
How many cylinders can the Link FuryX run?
With 8 injection drivers, the FuryX runs up to eight cylinders sequentially on fuel. Ignition is listed as 8 drivers in the retailer's spec table but 6 in its description, so confirm the count before planning coil-on-plug on a V8. Wasted spark reduces the drivers needed.Medium1
Does the Link FuryX have drive-by-wire?
Yes. The retailer lists fully programmable electronic throttle control, including a throttle blip on downshifts and an anti-lag mode. Cruise control is also listed. Confirm that your throttle body and pedal sensor are supported in PCLink before buying, and plan output allocation alongside fans and pumps.Medium1
How much logging does the Link FuryX have?
The FuryX has 512 MB of onboard data logging, according to a US retailer. Logs download over USB into PCLink. For comparison, Link's newer G5 Voodoo Neo 6 lists 1 GB of logging, along with onboard GPS and Wi-Fi. Laptop logging is also possible while connected.13
What looms does the Link FuryX need?
The FuryX needs an A loom and a B loom, or A and B pin kits for a custom harness. Both are sold separately from the ECU. Third-party makers also sell terminated harnesses for some engines. Budget for the looms when comparing prices with ECUs sold as kits.1
Related terms
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- Link G4X FuryX ECU [122-4000] listing · Wiring Specialties · reference · retrieved 2026-11-04
- G4X FuryX product page (dimensions, case, bracket) · Link Engine Management · vendor-doc · retrieved 2026-10-22
- G5 Voodoo Neo 6 product page · Link Engine Management · vendor-doc · retrieved 2026-10-24
- HT-067010 Haltech iC-7 Digital Dash Kit product page (ECU compatibility list) · Haltech · vendor-doc · retrieved 2026-11-04
A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.

