MoTeC · Standalone ECUs

MoTeC M130

Data loggers≈ €2,421 hardware only, ≈ €3,585 with GPR package (Polish dealer, incl. 23% VAT); ≈ A$3,000 + GST for the ASBK-spec kit

The MoTeC M130 is the smallest port-injection ECU in MoTeC's M1 range: 8 injector and 8 ignition outputs, 6 half-bridges, one CAN bus and Ethernet on a 60-pin, roughly 300 g package. It suits four- to eight-cylinder race cars and superbikes, and Australia's ASBK approved it as a Superbike-class ECU from 2022. Firmware packages such as GPR are bought separately.134

Illustration, not the product.

Key facts

Injector / ignition outputs8/ 8Sourced1
Aux outputs2 low-side + 6 half-bridgeSourced1
Inputs8 analog voltage, 4 temperature, 2 knock, 7 universal digitalSourced1
Connector pins60one 34-way + one 26-waySourced12
Size / weight107 × 127 × 39 mm, ≈ 300 g≈ 0.66 lbSourced · medium1

Suits

  • Superbikes and motorcycles, including ASBK Superbike entries
  • Four- to six-cylinder race cars where weight and space matter
  • Teams already using MoTeC dashes and analysis software

What it is and where it fits

The MoTeC M130 is the entry point to MoTeC's M1 ECU family.

It handles port-injected engines up to eight cylinders with one injector and one coil per cylinder, in a case about a third lighter than the M150.1

Its size makes it popular on motorcycles and compact race cars. Motorcycling Australia approved the M130 with ASBK-specific firmware as an alternative to manufacturer kit ECUs in the Superbike class from 2022.3

Hardware and I/O

MoTeC lists 8 low-impedance peak-and-hold injector outputs, 8 ignition outputs, 2 low-side and 6 half-bridge auxiliary outputs.

Unused injector and ignition channels can serve as extra low-side outputs.1

Inputs are 8 analog voltage, 4 temperature, 2 knock and 7 universal digital channels. That is enough for a typical four- or six-cylinder engine with drive-by-wire, but large sensor counts need CAN expanders.Medium1

The case measures 107 × 127 × 39 mm (4.2 × 5.0 × 1.5 in) and weighs about 300 g. Two plastic connectors give 60 pins in total.Medium12

Software and configuration

Like every M1 unit, the M130 runs a firmware package that defines its functions.

Dealers sell the ECU as hardware only and list General Purpose packages such as GPR separately for the M130, M150, M170 and M190.41

Series can lock the firmware. In ASBK trim, rider-adjustable traction control has 8 modes and engine braking has 3, while GPS-based mapping is blocked and the rev limit is capped at the manufacturer kit ECU's figure.3

Connectivity and expansion

The M130 has one CAN bus and no RS232 or LIN port, against three CAN buses on the M150.

All dashes, keypads, lambda modules and expanders share that single bus.1

Laptop tuning and log downloads run over Ethernet. Wideband lambda comes from MoTeC LTC lambda-to-CAN modules, which the ASBK package lists as part of a typical superbike kit.13

Installation notes

The ASBK information sheet lists the supporting parts for a superbike install: dash, IGN4 ignition driver, harness, CAN handlebar switches, LTC lambda module and suspension potentiometers. That list is a fair guide to the real system cost.3

Passive coils need an ignition amplifier such as MoTeC's IGN4. Plan harness length and connector access early, because the two connectors exit one end of a compact case.Medium31

Generations and variants

The M130 shares its 60-pin format with no direct-injection sibling; DI starts at the 120-pin M141 and M142.

Larger port-injection options are the M150, M170 and M190.1

Some dealers sell a bundled M130 and GPR part, listed as 13130AB. The same hardware also runs series-specific firmware, such as the locked ASBK superbike package.Medium43

Specifications

From the maker's published data and independent sources.

Outputs

SpecValueSource
Injector outputs8 low-impedance peak and hold1
Ignition outputs81
Auxiliary outputs2 low-side, 6 half-bridge1
Injector typePort injection1

Inputs

SpecValueSource
Analog voltage inputs81
Analog temperature inputs41
Knock inputs21
Universal digital inputs71

Communication and logging

SpecValueSource
CAN / RS232 / LIN1 / 0 / 01
PC connectionEthernet1
Maximum logging memory120 MBFrom MoTeC's early M1 brochure only; the M150 figure rose in later datasheets, so check the current M130 datasheet.UnverifiedLow1

Physical

SpecValueSource
ConnectorsPlastic, 34-way connector A + 26-way connector BMedium21
Dimensions107 × 127 × 39 mm (4.2 × 5.0 × 1.5 in)Medium1
Weight≈ 300 gMedium1

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • About 300 g and 107 × 127 × 39 mm, the lightest M1 unit in MoTeC's table.Medium1
  • Approved by Motorcycling Australia for ASBK Superbike use from 2022, with locked series firmware.3
  • Six half-bridge outputs cover drive-by-wire and other motor-driven actuators.1

Limits

  • Only one CAN bus, so every expansion device shares it.1
  • Limited to 8 injectors and 8 coils; staged fuel on an eight-cylinder needs a bigger unit.1
  • Hardware price excludes the firmware package, which costs about €1,163 at one dealer.Medium4

Often compared with

ProductCategoryKey fact
MoTeC M150Standalone ECUsInjector outputs: 12 peak and hold + 6 low-side
Link G4X FuryXStandalone ECUsInjection drivers: 8
ECUMaster EMU PRO-8Standalone ECUsOutputs / inputs: 31 / 24
Syvecs S7-PlusStandalone ECUsInjection / PWM outputs: 16 low-side, 10 A max each
Emtron KV8Standalone ECUsInjector / ignition outputs: 8 / 8
MaxxECU RACEStandalone ECUsInjector / ignition outputs: 8 peak and hold (8 A) / 8

Frequently asked

How many cylinders can a MoTeC M130 run?

MoTeC lists 8 injector and 8 ignition outputs, so the M130 runs up to eight cylinders with one injector and one coil each. Unused channels can become low-side outputs. Engines that need staged injectors or more than eight cylinders usually step up to the M150.1

Does the MoTeC M130 come with firmware?

No. Dealers sell the M130 as hardware only, and a firmware package such as GPR is bought separately, at about €1,163 from one Polish dealer. Some dealers offer a bundled M130 and GPR part, and race series can supply locked firmware of their own.43

Is the MoTeC M130 used in superbike racing?

Yes. Motorcycling Australia approved the M130 with ASBK-specific firmware for the Superbike class from 2022, as an option to manufacturer kit ECUs. The locked firmware offers traction, wheelie, launch and engine-brake control but blocks GPS-based mapping, according to the series information sheet.3

What is the difference between the M130 and M150?

The M130 has 60 pins, 8 injector and 8 ignition outputs, 6 half-bridges and one CAN bus, and weighs about 300 g. The M150 has 120 pins, 12 injector and 12 ignition outputs, 10 half-bridges, three CAN buses and weighs about 445 g.15

How much does a MoTeC M130 cost?

Prices vary by region and package. One Polish dealer lists the hardware at about €2,421 and the M130 with GPR at about €3,585, including VAT. The ASBK sheet quotes about A$3,000 plus GST for its series kit, before dash, harness and sensors.Medium43

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. M1 Series ECUs brochure with model specification table · MoTeC (hosted by a dealer) · vendor-doc · retrieved 2026-11-04
  2. M130 product page (connector description) · MoTeC · vendor-doc · retrieved 2026-11-04
  3. MA Approved ECU MoTeC M130 ECU 2022 Information · Motorcycling Australia / ASBK · standard · retrieved 2026-11-04
  4. MoTeC 13130AB M130 stand-alone ECU with GPR package · Tomson (PL) · reference · retrieved 2026-11-04
  5. M150 ECU datasheet, part 13150 (published 1 May 2015) · MoTeC (hosted by a dealer) · vendor-doc · retrieved 2026-11-04

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.