FuelTech · Standalone ECUs

FuelTech FT600

Dash displaysData loggersTraction controlBoost controllers≈ US$2,299 (FuelTech US, ECU without harness; shown against a US$2,999 comparison price)

The FuelTech FT600 is a standalone ECU with a built-in 4.3 in touchscreen, 16 injector outputs, 16 ignition-capable outputs, 20 configurable inputs, a 7 bar internal MAP sensor and an internal 256-channel logger, in an IP67 case. It leans toward drag racing, with traction, 2-step and 3-step, burnout and wheelie control. Wideband needs an external conditioner.1

Illustration, not the product.

Key facts

Injector outputs16up to 4 high-impedance injectors eachSourced1
Ignition outputs
  • 8 open-collector + 8 push-pull
  • Sequential to 12 cylinders
Sourced1
Inputs20 configurable + 2 strain gaugeSourced1
Screen4.3 in colour touchscreenSourced1
MAP sensorInternal 7 barto 6 bar ≈ 87 psi boostSourced12
Price≈ US$2,299 without harnessSourced · medium1

Suits

  • Drag cars needing 3-step, burnout, line lock and nitrous staging
  • High-boost builds that fit within the 7 bar internal MAP sensor
  • Builds that want an ECU-mounted screen instead of a separate dash

What it is and where it fits

The FuelTech FT600 is a standalone ECU with its own touchscreen, so the ECU doubles as a basic dash.

It sits between the FT550 and the FT700 in FuelTech's range.Medium123

The feature set leans toward drag racing: burnout mode, 2-step and 3-step, line lock, time-based limiters, wheelie control and up to 6 nitrous stages. Traction control, boost control and engine protection round it out.1

Hardware and I/O

Sixteen open-collector injector outputs each drive up to four high-impedance injectors.

Low-impedance injectors need FuelTech's external peak-and-hold unit, which raises the count to 32 injectors.1

Ignition uses 8 open-collector outputs with a 5 V source plus 8 push-pull or half-bridge outputs, for sequential spark on up to 12 cylinders. Thirty-two general outputs drive pumps, fans and valves.1

Twenty configurable inputs, two strain-gauge inputs for a shifter load cell and an internal 7 bar MAP sensor cover most drag builds. An accelerometer, gyroscope and inclinometer are built in.1

Software and configuration

Tuning uses FuelTech's FTManager software with live map editing, and logs open in FTDatalogger.

Basic changes can be made on the ECU's touchscreen.1

FuelTech notes that firmware 5.10 and later can also control electric vehicles.1

Connectivity and expansion

Two CAN ports run FuelTech's FTCAN 2.0 and 1.0 protocols to its wideband conditioners, displays and expansion modules.

FuelTech lists partial OEM CAN support for C6 and C7 Corvette, fifth-generation Camaro and 2009 CTS-V.1

The internal logger records up to 256 channels at 1-200 Hz per channel, about 2 hours 50 minutes at 24 channels and 25 Hz.1

Installation notes

FuelTech sells the FT600 without a harness, with a connector kit, with a 10 ft or 20 ft (3 or 6 m) unterminated harness, or with a complete PRO600 harness. The box includes a mounting kit, protective cover and mini-USB cable.1

Closed-loop lambda needs an external FuelTech wideband conditioner on CAN. Because the screen faces the driver, plan the ECU's location as you would a dash.Medium1

Generations and variants

The FT550 shares the 7 bar MAP sensor, logger and CAN layout with 12 injector outputs, 24 general outputs and 14 inputs, at about US$1,299. The FT600 adds 4 injector outputs, 8 general outputs, 6 inputs and onboard motion sensors.21

Specifications

From the maker's published data and independent sources.

Outputs

SpecValueSource
Injector outputs16 open-collector for high-impedance injectors, up to 4 per output; up to 32 injectors with external peak-and-hold units1
Sequential injectionUp to 24 outputs1
Ignition outputs8 open-collector with 5 V source + 8 push-pull/half-bridge1
Sequential ignitionUp to 12 cylinders1
General-purpose outputs32 total1

Inputs and sensors

SpecValueSource
Configurable inputs20 digital/analog1
Strain gauge inputs2 high-gain (e.g. shifter load cell)1
TriggerDifferential RPM and cam sync inputs1
MAP sensorInternal 7 bar (1 bar vacuum to 6 bar boost)1
Motion sensorsAccelerometer, gyroscope, inclinometer1
WidebandExternal conditioner required (no onboard controller listed)1

Display, communication and logging

SpecValueSource
Screen4.3 in colour anti-glare touchscreen, up to 4 dash screens1
CAN2 ports, FTCAN 2.0 and 1.01
LoggingUp to 256 channels, 1-200 Hz per channel; about 2 h 50 min at 24 channels and 25 Hz1
OEM CANPartial: C6/C7 Corvette, 5th-gen Camaro, 2009 CTS-V1

Physical

SpecValueSource
Dimensions5.86 × 3.7 × 2.42 in (149 × 94 × 61 mm), ECU only1
Weight20.74 oz (588 g), ECU only1
Ingress ratingIP671
Warranty1 year1

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • Built-in touchscreen acts as a basic dash.1
  • Internal 7 bar MAP sensor reads up to 6 bar (≈ 87 psi) of boost.1
  • Drag-racing functions are built in, including 3-step, burnout, line lock and wheelie control.1
  • IP67 rating.1

Limits

  • No onboard wideband; closed-loop lambda needs an external conditioner.1
  • Injector outputs suit high-impedance injectors only without the external peak-and-hold unit.1
  • Logging tops out at 200 Hz per channel.1

Often compared with

ProductCategoryKey fact
Holley Terminator XStandalone ECUsInjectors / coils: 8 high-impedance / 8
Haltech Nexus R5 VCUStandalone ECUsInjector / ignition outputs: 18 / 12
MaxxECU RACEStandalone ECUsInjector / ignition outputs: 8 peak and hold (8 A) / 8
Haltech Elite 2500Standalone ECUsInjector / ignition outputs: 8 / 8

Frequently asked

Does the FuelTech FT600 have a built-in wideband?

No. FuelTech lists closed-loop O2 control through an external wideband conditioner, such as its WB-O2 Nano or WBO2 Datalogger, connected over CAN. Budget for at least one conditioner and sensor when comparing the FT600 with ECUs that include wideband control onboard.1

How many injectors can the FuelTech FT600 run?

Sixteen injector outputs each drive up to four high-impedance injectors, and full sequential injection covers up to 24 outputs. With FuelTech's external peak-and-hold unit, the system handles up to 32 injectors, including low-impedance types. Sequential ignition covers up to 12 cylinders.1

What is the difference between FT550 and FT600?

The FT600 has 16 injector outputs, 32 general outputs and 20 inputs, plus a built-in speed sensor, gyroscope and accelerometer. The FT550 has 12 injector outputs, 24 general outputs and 14 inputs. FuelTech lists the FT550 at about US$1,299 and the FT600 at about US$2,299.12

What MAP sensor does the FT600 have?

The FT600 has an internal 7 bar MAP sensor that reads from 1 bar of vacuum to 6 bar (about 87 psi) of boost. FuelTech also lists presets for external GM 1, 2 and 3 bar sensors for installs that need the sensor elsewhere. A 7 bar sensor trades some resolution at low load for range.1

Is the FuelTech FT600 waterproof?

FuelTech rates the FT600 IP67 and describes it as suitable for marine and off-road use. IP67 means dust-tight and protected against temporary immersion. Keep connectors fully seated and sealed, because the rating assumes a complete installation. Fit the supplied protective cover when the unit is exposed.1

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. FT600 EFI System product page · FuelTech · vendor-doc · retrieved 2026-11-04
  2. FT550 EFI System product page · FuelTech · vendor-doc · retrieved 2026-11-04
  3. FuelTech home page (ECU range: FT450, FT550, FT600, FT700) · FuelTech · vendor-doc · retrieved 2026-11-04

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.