Haltech · Power distribution modules

Haltech PD16 PDM

≈ $1,099 USD list (Haltech US store)

The Haltech PD16 is a 16-output power distribution module that works only as part of a Haltech Elite or Nexus engine management system. It provides ten 8 A high-side outputs, two half-bridge outputs, four 25 A high-current outputs and eight inputs, joins the Haltech CAN network and is programmed in the same software as the ECU.12

+12V
Illustration, not the product.

Key facts

Outputs1610 high-side, 2 half-bridge, 4 × 25 ASourced1
Inputs8 + dedicated ignition switch inputSourced1
Main power120 A SurLok connectorSourced1
CompatibilityHaltech Elite and Nexus ECUs onlySourced1
List price (US)≈ $1,099Haltech US store regular price, November 2026; sale prices and regional prices vary.Sourced1

Suits

  • Cars already running a Haltech Elite or Nexus ECU
  • Drag and street-strip builds replacing relays and a fuse board
  • Builds that need two half-bridge outputs for cutouts or wastegates

What it is and where it fits

The Haltech PD16 is a power distribution module built as an extension of a Haltech ECU.

Haltech states that it works only with Elite and Nexus ECUs and does not function as a standalone PDM.1

Dragzine described the PD16 as new in April 2022. Haltech developed it from the power distribution built into the Nexus R5 vehicle control unit and made it backward compatible with the Elite range.Medium2

It suits drag, street and track cars already running a Haltech ECU that want relays and fuses replaced without learning a separate PDM tool.Medium21

Hardware and I/O

Ten 8 A high-side outputs drive lights, small pumps and fans.

Four 25 A outputs take the heavy loads, such as fuel pumps, cooling fans and electric water pumps.12

Two half-bridge outputs can drive a motor in both directions. That covers push-pull devices such as exhaust cutouts, electronic wastegates and dump valves.21

There are eight programmable inputs, a dedicated ignition switch input, a 5 V sensor supply and sensor ground. Main battery power enters through a 120 A SurLok connector.1

Software and configuration

The PD16 is programmed in the same Haltech software used for the ECU, so outputs can be triggered directly from engine data.

Dragzine gives the example of a cooling fan wired straight from the PD16 to ground and switched on ECU data.Medium2

If a wiring short occurs, the PD16 can tell the ECU, switch off that circuit and raise a warning on a Haltech iC-7 dash.Medium2

Connectivity and expansion

The PD16 joins the Haltech CAN network through a plug-and-play CAN connection to an Elite or Nexus ECU.

A USB-C port on the unit connects the laptop.12

Because it depends on the Haltech ECU, it cannot be added to a car running another brand of ECU. Cars on other systems need a standalone PDM instead.1

Installation notes

Haltech sells a 5 m (16 ft) flying lead harness, HT-188000, for building the loom, and a clamp kit for mounting the unit on a 1.25 in (31.75 mm) roll-cage tube. Retailers also sell the PD16 with a plug and pin set, at $1,175 from one US dealer.14

A PDM still needs wiring and setup. Dragzine notes that it is not a plug-and-play item, though simpler than many wiring jobs.Medium2

Generations and variants

The PD16 is sold as one hardware version, part HT-198000.

Haltech's Nexus R5 vehicle control unit builds power distribution into the ECU itself, which is the alternative for new builds.Medium12

Specifications

From the maker's published data and independent sources.

Outputs

SpecValueSource
High-side outputs10, rated 8 A each12
Half-bridge outputs2, for push-pull devices such as exhaust cutouts and electronic wastegates12
High-current outputs4, rated 25 A each12
Ignition switch supplyPower provided for the ignition switch1
Total currentNot published as a single figure; main feed uses a 120 A SurLok connectorHaltech's product page gives the 120 A connector rating but no total continuous output figure.UnverifiedMedium1

Inputs and communications

SpecValueSource
Inputs8 programmable inputs plus a dedicated ignition switch input1
Sensor supply5 V sensor supply and sensor ground1
NetworkHaltech CAN bus network, plug-in connection to Elite or Nexus12
PC connectionUSB-C (cable and dust cap included)1

In the box and accessories

SpecValueSource
IncludedPD16, red 120 A SurLok connector, USB-C cable, USB-C dust cap, quick start guide, M5 mounting hardware1
Flying lead harnessHT-188000, 5 m (16 ft), ≈ $315 USD list1
Tube mount kitHT-039080 for 31.75 mm (1.25 in) tube, ≈ $125 USD list1
Part numberHT-1980001

Strengths and limits

Facts, each cited. Not a score.

Strengths

  • Configured in the same software as the Haltech ECU, so outputs use engine data with no separate CAN setup.Medium2
  • Two half-bridge outputs drive bidirectional devices such as exhaust cutouts and electronic wastegates.21
  • USB-C port and tool-free SurLok main power connector.1

Limits

  • Works only with Haltech Elite and Nexus ECUs; it is not a standalone PDM.1
  • Eight inputs, fewer than many standalone PDMs.1
  • Haltech publishes no total continuous current, size or weight on the product page.Medium1

Often compared with

ProductCategoryKey fact
Haltech Nexus R5 VCUStandalone ECUsInjector / ignition outputs: 18 / 12
ECUMaster PMU-16Power distribution modulesOutputs: 16 (10 × 25 A + 6 × 15 A)
MoTeC PDM15Power distribution modulesOutputs: 15 (8 × 20 A + 7 × 8 A)
AiM PDM32Power distribution modulesOutputs: 32 (28 high-side + 4 × 35 A configurable)
Haltech CAN KeypadCAN keypadsLayouts: 8 buttons (2 × 4) or 15 buttons (3 × 5)

Frequently asked

Does the Haltech PD16 work without a Haltech ECU?

No. Haltech states the PD16 is compatible with Haltech Elite and Nexus ECUs only and does not function as a standalone PDM. It joins the Haltech CAN network and is configured through the ECU's software. Cars running another ECU brand need a standalone PDM instead.1

How many outputs does the Haltech PD16 have?

The PD16 has 16 outputs: ten high-side outputs rated 8 A, two half-bridge outputs and four high-current outputs rated 25 A. It also has eight programmable inputs plus a dedicated ignition switch input, a 5 V sensor supply and a sensor ground.12

What software programs the Haltech PD16?

The PD16 is set up in the same Haltech software as the Elite or Nexus ECU it connects to. Haltech's design goal, reported by Dragzine, was to manage the ECU and PDM from one program. A USB-C cable connects the laptop.Medium21

What is a half-bridge output on the PD16?

A half-bridge output can switch its pin to either supply or ground. Two of them drive a small motor in both directions. On the PD16 they suit push-pull devices such as exhaust cutouts, electronic wastegates and dump valves, which need driving open and closed.Medium2

How is the Haltech PD16 powered?

Main battery power enters through a 120 A SurLok connector, and the red mating connector comes in the box. The PD16 also provides power for the ignition switch and reads it on a dedicated input. Size the battery cable and its protection for the full load.1

How much does the Haltech PD16 cost?

Haltech's US store listed the PD16 at $1,099 regular price in November 2026, with a sale price below that. A UK retailer listed it at £1,035 including VAT. The 5 m flying lead harness is about $315 extra, and kits with a plug and pin set cost more.134

Related terms

Sources

Numbered as cited above. Hover or tap a citation chip to preview it.

  1. HT-198000 PD16 PDM product page · Haltech · vendor-doc · retrieved 2026-11-04
  2. What Is A PDM And How Is Haltech's PD16 So Different? · Dragzine · press · retrieved 2026-11-04
  3. Haltech PD16 PDM Power Distribution Module listing · EXO Racing · reference · retrieved 2026-11-04
  4. Haltech PD16 Power Distribution Module (PDM+) Plug & Pin Set listing · Hybrid Racing · reference · retrieved 2026-11-04

A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.