Key facts
Suits
- Full race builds wired from scratch around one power and data hub
- Teams already using AiM dashes, SmartyCam and RaceStudio
- Cars that want output currents logged next to sensor and GPS data
What it is and where it fits
The AiM PDM32 merges a power distribution module and a data logger in one case.
It replaces fuses and relays with protected solid-state outputs and logs sensors, ECU data, GPS and the state of every output.12
AiM intends the car's wiring to be built around it, with new chassis wiring and connectors rather than reuse of the old loom. That makes it a fit for full race builds rather than a bolt-in upgrade.Medium2
Kits add a 6 in or 10 in AiM TFT display linked by cable. Display versions come with race icons or road icons, the latter showing street-car warning lights such as check engine and oil pressure.Medium23
Hardware and I/O
The 28 high-side outputs come in three sizes: four rated up to 20 A (one with a series diode), twelve up to 15 A and twelve up to 10 A. Total output is capped at 120 A.1
Four further outputs handle up to 35 A and can be set as high-side, low-side, half-bridge or PWM up to 500 Hz. In half-bridge mode an output can switch to supply or ground, which lets a pair drive a motor both ways.Medium1
The 14 inputs record at up to 500 Hz: eight analog (0-5 V or 0-12 V) or digital, four digital and two speed inputs. Two analog video inputs feed a camera to the display.1
The anodized aluminum case is sealed to IP65 and measures 234.5 × 94.6 × 49.5 mm (9.2 × 3.7 × 1.9 in), weighing 761 g. Main power enters through an Amphenol SurLok connector.1
Software and configuration
AiM's RaceStudio software configures outputs, inputs, logging and the display layout.
Inrush current, the number of fault retries and the time between retries are set per output.Medium2
Multicolor LEDs on the case show each output's status, including open circuit, short circuit, high temperature, over-current and voltage faults.21
Connectivity and expansion
Three CAN connections and one LIN bus link the ECU, keypads and AiM expansion modules.
AiM lists the GPS09c, channel expansion, TC Hub, lambda controller, SmartyCam 3, steering wheel and memory module as compatible.1
The 4 GB memory logs analog and digital inputs, ECU channels, GPS, camera and the current and status of every output. Data downloads over a USB port on a Binder connector.12
Installation notes
Signals run through two 35-pin AMP connectors.
The display connects through a Rosenberger connector, with a 2 m cable in the kit BimmerWorld lists.12
The PDM32 runs on 9 to 15 V, so it suits 12 V cars, not 24 V systems. Kits ship with different GPS cable lengths, so measure the antenna route before ordering.12
Generations and variants
AiM sells the PDM32 as a module only, or in kits with a 6 in or 10 in display, race or road icons and different GPS cable lengths.
A smaller sibling, the PDM08, has 8 outputs and works with the same TFT displays.Medium32
The technical sheet referenced here is version 1.17. Check AiM's current sheet for any change in output ratings before wiring.1
Specifications
From the maker's published data and independent sources.
Power outputs
| Spec | Value | Source |
|---|---|---|
| 20 A high-side | 1 with series diode plus 3 more, each up to 20 A | 1 |
| 15 A high-side | 12, each up to 15 A | 1 |
| 10 A high-side | 12, each up to 10 A | 1 |
| Configurable outputs | 4, up to 35 A; high-side, half-bridge, low-side or PWM up to 500 Hz | 1 |
| Protection | Over- and under-voltage, short circuit, over-current, over-temperature | 1 |
| Total current | 120 A max | 1 |
Inputs, logging and communications
| Spec | Value | Source |
|---|---|---|
| Inputs | 14, each recorded at up to 500 Hz: 8 analog (0-5 V or 0-12 V) or digital, 4 digital, 2 speed | 1 |
| CAN | 3 connections | 1 |
| LIN | 1 | 1 |
| Internal memory | 4 GB | 1 |
| Camera inputs | 2 analog video inputs | 1 |
| Display link | 1 AiM stream output for a remote display | 1 |
| Inertial sensor | Internal 9-axis inertial platform | Medium2 |
| External modules | GPS09c, channel expansion, TC Hub, lambda controller, SmartyCam 3, steering wheel, memory module, keypads | 1 |
Physical and electrical
| Spec | Value | Source |
|---|---|---|
| Supply voltage | 9-15 V | 1 |
| Connectors | 2 × 35-pin AMP, 2 × Binder (USB, video), 1 × Amphenol SurLok power, 1 × Rosenberger display link | 12 |
| Status LEDs | 32 RGB output LEDs plus PDM ON and status LEDs | 1 |
| Body | Anodized aluminum, IP65 | 1 |
| Dimensions | 234.5 × 94.6 × 49.5 mm (9.23 × 3.72 × 1.95 in) | 12 |
| Weight | 761 g (1.68 lb) | 1 |
Strengths and limits
Facts, each cited. Not a score.
Strengths
Often compared with
| Product | Category | Key fact |
|---|---|---|
| MoTeC PDM30 | Power distribution modules | Outputs: 30 (8 × 20 A + 22 × 8 A) |
| MoTeC PDM15 | Power distribution modules | Outputs: 15 (8 × 20 A + 7 × 8 A) |
| ECUMaster PMU-16 | Power distribution modules | Outputs: 16 (10 × 25 A + 6 × 15 A) |
| Haltech PD16 PDM | Power distribution modules | Outputs: 16 (10 high-side, 2 half-bridge, 4 × 25 A) |
| AiM MXS 1.2 Strada | Dash displays | Screen: 5 in TFT, 800 × 480 (1.3 Strada) |
Frequently asked
What is the AiM PDM32?
It is a power distribution module with a built-in data logger. It has 32 protected outputs with 120 A total, 14 inputs, three CAN buses, a LIN bus, two camera inputs and 4 GB of memory. AiM sells it alone or in kits with a 6 in or 10 in display and GPS.12
Does the AiM PDM32 log data?
Yes. It has 4 GB of internal memory and records its inputs at up to 500 Hz each. It logs analog and digital inputs, ECU channels, GPS values, camera and the current and status of every power output, so electrical faults line up with the rest of the data.12
How many outputs does the AiM PDM32 have?
It has 32. Twenty-eight are high-side outputs: four up to 20 A, twelve up to 15 A and twelve up to 10 A. Four more handle up to 35 A and can be set as high-side, low-side, half-bridge or PWM. AiM lists 120 A as the total.1
What display works with the AiM PDM32?
AiM pairs the PDM32 with its own 6 in or 10 in TFT displays, connected through a Rosenberger cable to the PDM's display output. Displays come with race icons or road icons; the road version shows street-car warning lights such as check engine and oil pressure. The module can also run without a display.Medium21
What software configures the AiM PDM32?
AiM RaceStudio configures the PDM32, including outputs, inputs, logging and the display pages. Per output, users can set inrush current, the number of fault retries and the time between retries. The same software family handles analysis of the logged data.Medium2
Related terms
Sources
Numbered as cited above. Hover or tap a citation chip to preview it.
- AiM PDM32 Power Distribution Module technical sheet, version 1.17 · AiM Sportline · vendor-doc · retrieved 2026-11-04
- AiM PDM32 Power Module and Logger with 6" Road/Race Display · BimmerWorld · reference · retrieved 2026-11-04
- AiM Power Distribution Module PDM32, module only · AimShop · reference · retrieved 2026-11-04
A technical overview from published sources; we have not tested this product. Product names are the property of their owners and identify the product only; GAINS is not affiliated with, or endorsed by, the maker.

